Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM(for Type C) › from 2016.03
RM3250E _58 Vehicle Interior _038070 SUPPLEMENTAL RESTRAINT SYSTEMS _0265842 AIRBAG SYSTEM(for Type C) C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(for Type C)  B162C/85  Side Airbag Sensor Assembly No.2 Initialization Error (RH)  B163C/86  Side Airbag Sensor Assembly No.2 Initialization Error (LH)  


DESCRIPTION

The circuit for the side collision sensor LH or RH is composed of the airbag sensor assembly, front floor side airbag sensor LH or RH.

The front floor side airbag sensor LH or RH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbag should be deployed.

DTC B162A/2A or B163A/3A is stored when a malfunction is detected in the circuit for the side collision sensor LH or RH.

DTC No. Detection Item DTC Detection Condition Trouble Area
B162C/85 Side Airbag Sensor Assembly No.2 Initialization Error (RH) One of the following conditions is met:
·

The airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the circuit for the side collision sensor RH for 2 seconds.

·

A front floor side airbag sensor RH malfunction.

·

An airbag sensor assembly malfunction.


·

Front floor side airbag sensor RH

·

Floor wire

·

Airbag sensor assembly


B163C/86 Side Airbag Sensor Assembly No.2 Initialization Error (LH) One of the following conditions is met:
·

The airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the circuit for the side collision sensor LH for 2 seconds.

·

A front floor side airbag sensor LH malfunction.

·

An airbag sensor assembly malfunction.


·

Front floor side airbag sensor LH

·

Floor wire

·

Airbag sensor assembly



WIRING DIAGRAM

for RH Side:
C354997E01
1.229,0.917 1.844,1.115 0.615,0.198 10 false BFR+ 1.26,2.073 1.875,2.271 0.615,0.198 10 false BFR- 5.583,0.906 6.198,1.104 0.615,0.198 10 false BCR+ 5.594,2.073 6.208,2.271 0.615,0.198 10 false BCR- 5.417,2.792 5.875,2.99 0.458,0.198 10 false N41 0.385,2.802 0.844,3 0.458,0.198 10 false N38 1.688,0.802 2.01,1.031 0.323,0.229 10 false 2 1.688,1.969 1.99,2.188 0.302,0.219 10 false 1 5.323,0.792 5.646,1.021 0.323,0.229 10 false 20 5.313,1.969 5.635,2.198 0.323,0.229 10 false 19 0.385,2.969 2.719,3.24 2.333,0.271 10 false Front Floor Side Airbag Sensor RH 5.417,2.958 7.104,3.219 1.688,0.26 10 false Airbag Sensor Assembly

for LH Side:
C354997E02
1.229,0.917 1.844,1.115 0.615,0.198 10 false BFL+ 1.26,2.073 1.875,2.271 0.615,0.198 10 false BFL- 5.583,0.906 6.198,1.104 0.615,0.198 10 false BCL+ 5.594,2.073 6.208,2.271 0.615,0.198 10 false BCL- 5.417,2.792 5.875,2.99 0.458,0.198 10 false N40 0.385,2.802 0.844,3 0.458,0.198 10 false N39 1.688,0.802 2.01,1.031 0.323,0.229 10 false 2 1.688,1.969 1.99,2.188 0.302,0.219 10 false 1 5.323,0.792 5.646,1.021 0.323,0.229 10 false 21 5.313,1.969 5.635,2.198 0.323,0.229 10 false 22 0.385,2.969 2.719,3.24 2.333,0.271 10 false Front Floor Side Airbag Sensor LH 5.417,2.958 7.104,3.219 1.688,0.26 10 false Airbag Sensor Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After replacing the airbag sensor assembly, refer to initialization.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch to ON.


b.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type C)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type C)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B163A/3A is output
DTC B162A/2A is output
DTC B162A/2A and B163A/3A are not output


HINT:

Codes other than DTC B162A/2A and B163A/3A may be output at this time, but they are not related to this check.




DTC B163A/3A is output

2.CHECK CONNECTION OF CONNECTORS

DTC B162A/2A is output

6.CHECK CONNECTION OF CONNECTORS

DTC B162A/2A and B163A/3A are not output

2.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the airbag sensor assembly and front floor side airbag sensor LH.


Result:
Proceed to
The connectors are properly connected
The connectors are not properly connected



The connectors are properly connected

3.CHECK CONNECTORS

The connectors are not properly connected

CONNECT CONNECTORS PROPERLY

3.CHECK CONNECTORS
a.

Disconnect the connectors from the airbag sensor assembly and front floor side airbag sensor LH.


b.
C208244C30
0.354,1.333 0.667,1.49 0.313,0.156 10 *1 2.115,1.792 2.427,1.948 0.313,0.156 10 *2 1.521,1.052 1.833,1.208 0.313,0.156 10 *3
*1 Front Floor Side Airbag Sensor LH
*2 Airbag Sensor Assembly
*3 Floor Wire


Check that the connectors (on the airbag sensor assembly side and front floor side airbag sensor LH side) are not damaged.


Result:
Proceed to
The connectors are not deformed or damaged
The connectors are deformed or damaged



The connectors are not deformed or damaged

4.CHECK FRONT FLOOR SIDE AIRBAG SENSOR LH

The connectors are deformed or damaged

REPLACE FLOOR WIRE

4.CHECK FRONT FLOOR SIDE AIRBAG SENSOR LH
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

C354999C01
3.052,0.813 3.406,1.063 0.354,0.25 5.125,0.802 5.479,1.052 0.354,0.25 3.438,1.375 3.854,0.958 true 4.406,1.385 4.031,0.958 true 5.792,1.573 5.938,1.448 true 5.594,1.333 6.031,1.042 true 6.625,1.448 6.125,1.042 true 1.844,0.406 2,0.604 0.156,0.198 10 false A 1.458,0.615 1.615,0.813 0.156,0.198 10 false B 0.958,0.615 1.115,0.813 0.156,0.198 10 false C 0.583,0.396 0.74,0.594 0.156,0.198 10 false D 1.156,0.219 1.469,0.417 0.313,0.198 10 false *3 0.448,0.813 0.76,1.01 0.313,0.198 10 false *1 2,1.156 2.313,1.354 0.313,0.198 10 false *2 3.49,0.125 3.802,0.323 0.313,0.198 10 false *a 5.74,0.073 6.052,0.271 0.313,0.198 10 false *b 3.854,0.344 4.167,0.542 0.313,0.198 10 false *4 6.052,0.25 6.365,0.448 0.313,0.198 10 false *5 5.583,1.479 5.896,1.677 0.313,0.198 10 false *6 5.188,0.844 5.646,1.042 0.458,0.198 10 false N40 3.115,0.865 3.573,1.063 0.458,0.198 10 false N39 3.094,1.292 3.708,1.49 0.615,0.198 10 false BFL- 4.448,1.323 5.063,1.521 0.615,0.198 10 false BFL+ 6.667,1.385 7.104,1.635 0.438,0.25 10 false BCL+ 5.24,1.26 5.854,1.458 0.615,0.198 10 false BCL-
*1 Front Floor Side Airbag Sensor LH *2 Airbag Sensor Assembly
*3 Floor Wire *4 Connector C
*5 Connector B *6 Service Wire
*a Front view of wire harness connector
(to Front Floor Side Airbag Sensor LH)
*b Rear view of wire harness connector
(to Airbag Sensor Assembly)



b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N39-2 (BFL+) - Body ground Ignition switch ON Below 1 V
N39-1 (BFL-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 21 (BCL+) and 22 (BCL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N39-2 (BFL+) - N39-1 (BFL-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N39-2 (BFL+) - N39-1 (BFL-) Always 1 MΩ or higher
N39-2 (BFL+) - Body ground Always 1 MΩ or higher
N39-1 (BFL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK FRONT FLOOR SIDE AIRBAG SENSOR LH

NG

REPLACE FLOOR WIRE

5.CHECK FRONT FLOOR SIDE AIRBAG SENSOR LH
a.

Connect the connectors to the airbag sensor assembly.


b.
C146229C47
0.854,0.99 1.021,1.146 0.167,0.156 10 false *1 1.823,1.313 1.99,1.479 0.167,0.167 10 false *2
*1 Front Floor Side Airbag Sensor RH
*2 Airbag Sensor Assembly


Interchange the front floor side airbag sensor LH with RH and connect the connectors to them.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type C)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type C)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B162A/2A is output
DTC B163A/3A is output
DTC B162A/2A and B163A/3A are not output


HINT:

Codes other than DTC B162A/2A and B163A/3A and B1637/82 may be output at this time, but they are not related to this check.



i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


k.

Return the front floor side airbag sensor RH and LH to their original positions and connect the connectors to them.



DTC B162A/2A is output

REPLACE FRONT FLOOR SIDE AIRBAG SENSOR LH

DTC B163A/3A is output

DTC B162A/2A and B163A/3A are not output

6.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the airbag sensor assembly and front floor side airbag sensor RH.


Result:
Proceed to
The connectors are properly connected
The connectors are not properly connected



The connectors are properly connected

7.CHECK CONNECTORS

The connectors are not properly connected

CONNECT CONNECTORS PROPERLY

7.CHECK CONNECTORS
a.

Disconnect the connectors from the airbag sensor assembly and front floor side airbag sensor RH.


b.
C354998C01
1.542,0.906 1.854,1.104 0.313,0.198 10 false *3 2.563,1.438 2.875,1.635 0.313,0.198 10 false *2 0.708,1.646 1.021,1.844 0.313,0.198 10 false *1
*1 Front Floor Side Airbag Sensor RH
*2 Airbag Sensor Assembly
*3 Floor Wire


Check that the connectors (on the airbag sensor assembly side and front floor side airbag sensor RH side) are not damaged.


Result:
Proceed to
The connectors are not deformed or damaged
The connectors are deformed or damaged



The connectors are not deformed or damaged

8.CHECK FRONT FLOOR SIDE AIRBAG SENSOR RH

The connectors are deformed or damaged

REPLACE FLOOR WIRE

8.CHECK FRONT FLOOR SIDE AIRBAG SENSOR RH
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

C355000C01
2.969,0.802 3.344,1.01 0.375,0.208 5.083,0.781 5.458,0.99 0.375,0.208 3.448,1.375 3.865,0.958 true 4.427,1.396 4.031,0.958 true 6.656,0.646 6.292,1.031 true 5.51,1.365 6.198,1.042 true 5.854,1.594 6.094,1.458 true 2.063,1.063 2.375,1.26 0.313,0.198 10 false *2 1.135,0.594 1.448,0.792 0.313,0.198 10 false *3 0.469,1.188 0.781,1.385 0.313,0.198 10 false *1 3.552,0.135 3.865,0.333 0.313,0.198 10 false *a 3.833,0.344 4.146,0.542 0.313,0.198 10 false *4 5.771,0.083 6.083,0.281 0.313,0.198 10 false *b 6.083,0.271 6.396,0.469 0.313,0.198 10 false *5 5.688,1.531 6,1.729 0.313,0.198 10 false *6 4.479,1.333 5.094,1.531 0.615,0.198 10 false BFR+ 3.083,1.281 3.698,1.479 0.615,0.198 10 false BFR- 5.115,1.292 5.729,1.49 0.615,0.198 10 false BCR+ 6.698,0.563 7.125,0.771 0.427,0.208 10 false BCR- 5.146,0.802 5.604,1 0.458,0.198 10 false N41 3.031,0.823 3.49,1.021 0.458,0.198 10 false N38 1.844,0.781 2,0.979 0.156,0.198 10 false A 1.458,1 1.615,1.198 0.156,0.198 10 false B 0.948,0.99 1.104,1.188 0.156,0.198 10 false C 0.583,0.771 0.74,0.969 0.156,0.198 10 false D
*1 Front Floor Side Airbag Sensor RH *2 Airbag Sensor Assembly
*3 Floor Wire *4 Connector C
*5 Connector B *6 Service Wire
*a Front view of wire harness connector
(to Front Floor Side Airbag Sensor RH)
*b Rear view of wire harness connector
(to Airbag Sensor Assembly)



b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N38-2 (BFR+) - Body ground Ignition switch ON Below 1 V
N38-1 (BFR-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 20 (BCR+) and 19 (BCR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N38-2 (BFR+) - N38-1 (BFR-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N38-2 (BFR+) - N38-1 (BFR-) Always 1 MΩ or higher
N38-2 (BFR+) - Body ground Always 1 MΩ or higher
N38-1 (BFR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK FRONT FLOOR SIDE AIRBAG SENSOR RH

NG

REPLACE FLOOR WIRE

9.CHECK FRONT FLOOR SIDE AIRBAG SENSOR RH
a.

Connect the connectors to the airbag sensor assembly.


b.
C171812C09
0.719,1.271 0.875,1.438 0.156,0.167 10 *1 1.844,1.125 2.031,1.292 0.188,0.167 10 *2
*1 Front Floor Side Airbag Sensor LH
*2 Airbag Sensor Assembly


Interchange the front floor side airbag sensor LH with RH and connect the connectors to them.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type C)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type C)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B163A/3A is output
DTC B162A/2A is output
DTC B162A/2A and B163A/3A are not output


HINT:

Codes other than DTC B162A/2A and B163A/3A may be output at this time, but they are not related to this check.



i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


k.

Return the front floor side airbag sensor LH and RH to their original positions and connect the connectors to them.



DTC B163A/3A is output

REPLACE FRONT FLOOR SIDE AIRBAG SENSOR RH

DTC B162A/2A is output

DTC B162A/2A and B163A/3A are not output