Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM(for Type C) › from 2016.03
RM3250E _58 Vehicle Interior _038070 SUPPLEMENTAL RESTRAINT SYSTEMS _0265842 AIRBAG SYSTEM(for Type C) C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(for Type C)  B1650/32  Occupant Classification System Malfunction  


DESCRIPTION

The occupant classification system circuit consists of the airbag sensor assembly and occupant detection ECU.

If the airbag sensor assembly receives signals from the occupant detection ECU, it determines whether the instrument panel passenger airbag, front seat airbag LH*1/RH*2 and front seat outer belt assembly should be operated.

DTC B1650/32 is stored when a malfunction is detected in the occupant classification system circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1650/32 Occupant Classification System Malfunction
One of the following conditions is met:
·

An occupant classification system malfunction.

·

The airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the occupant classification system circuit for 2 seconds.

·

An airbag sensor assembly malfunction.


·

Floor wire

·

Front seat wire LH*1

·

Front seat wire RH*2

·

Occupant detection ECU

·

Airbag sensor assembly



·

*1: for RHD

·

*2: for LHD


WIRING DIAGRAM

C238367E41
0.583,3.104 2.323,3.333 1.74,0.229 10 false Occupant Detection ECU 0.583,2.938 1.063,3.177 0.479,0.24 10 false T10 3.417,0.906 3.802,1.125 0.385,0.219 10 false NT2 3.5,0.698 3.74,0.927 0.24,0.229 10 false 1 3.5,1.875 3.708,2.094 0.208,0.219 10 false 4 5.198,0.802 5.448,1.042 0.25,0.24 10 false 9 5.135,1.958 5.458,2.219 0.323,0.26 10 false 17 5.354,2.948 5.771,3.302 0.417,0.354 10 false N40 5.365,3.115 7.104,3.365 1.74,0.25 10 false Airbag Sensor Assembly 1.406,0.885 2.083,1.198 0.677,0.313 10 false FSR+ 1.427,2.063 2,2.396 0.573,0.333 10 false FSR- 5.385,0.906 5.833,1.323 0.448,0.417 10 false FSL+ 5.385,2.083 5.802,2.479 0.417,0.396 10 false FSL- 1.854,0.802 2.115,1.052 0.26,0.25 10 false 8 1.865,1.969 2.094,2.229 0.229,0.26 10 false 4 3.417,2.073 3.802,2.292 0.385,0.219 10 false NT2 0.052,0.052 1.344,0.292 1.292,0.24 12 false for RHD:

C238367E42
0.583,3.104 2.323,3.333 1.74,0.229 10 false Occupant Detection ECU 0.583,2.938 1.063,3.177 0.479,0.24 10 false S10 3.417,0.906 3.802,1.125 0.385,0.219 10 false NS2 3.5,0.698 3.74,0.927 0.24,0.229 10 false 1 3.5,1.875 3.708,2.094 0.208,0.219 10 false 4 5.125,0.802 5.458,1.031 0.333,0.229 10 false 16 5.135,1.958 5.448,2.198 0.313,0.24 10 false 24 5.354,2.948 5.771,3.302 0.417,0.354 10 false N41 5.365,3.115 7.083,3.396 1.719,0.281 10 false Airbag Sensor Assembly 1.406,0.885 2.083,1.198 0.677,0.313 10 false FSR+ 1.427,2.063 2,2.396 0.573,0.333 10 false FSR- 5.385,0.906 5.833,1.323 0.448,0.417 10 false FSR+ 5.385,2.083 5.802,2.479 0.417,0.396 10 false FSR- 1.854,0.802 2.115,1.052 0.26,0.25 10 false 8 1.865,1.969 2.094,2.229 0.229,0.26 10 false 4 3.417,2.073 3.802,2.292 0.385,0.219 10 false NS2 0.042,0.052 1.115,0.25 1.073,0.198 12 false for LHD:

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After replacing the airbag sensor assembly, refer to initialization.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch on (IG), and wait for at least 60 seconds.


b.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Clear DTCs
50002 59
HINT:
·

First clear the DTCs stored in the occupant detection ECU, and then clear the DTCs stored in the airbag sensor assembly.

·

Use the GTS to clear the DTCs of the occupant detection ECU, otherwise the DTCs cannot be cleared.




c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Check for DTCs of the occupant detection ECU.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Occupant Detection > Trouble Codes
50001 59

Result:
Proceed to
DTC is not output
DTC is output



DTC is not output

2.CHECK DTC

DTC is output

2.CHECK DTC
a.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type C)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type C)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1650/32 is not output
DTC B1650/32 is output


HINT:

Codes other than DTC B1650/32 may be output at this time, but they are not related to this check.




DTC B1650/32 is not output

DTC B1650/32 is output

3.CHECK CONNECTION OF CONNECTORS
3.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the airbag sensor assembly and occupant detection ECU.


Result:
Proceed to
Connectors are properly connected
Connectors are not properly connected



Connectors are properly connected

4.CHECK CONNECTORS

Connectors are not properly connected

CONNECT CONNECTORS PROPERLY

4.CHECK CONNECTORS
a.
C350417C01
0.844,1.083 1.156,1.281 0.313,0.198 10 false *1 2.448,1.49 2.76,1.688 0.313,0.198 10 false *2 0.104,0.094 0.479,0.333 0.375,0.24 12 false *A
*A for RHD
*1 Occupant Detection ECU
*2 Airbag Sensor assembly


C354990C01
0.177,0.135 0.552,0.375 0.375,0.24 12 false *A 2.469,1.302 2.781,1.5 0.313,0.198 10 false *2 0.833,1.333 1.146,1.531 0.313,0.198 10 false *1
*A for LHD
*1 Occupant Detection ECU
*2 Airbag Sensor assembly


Disconnect the connectors from the airbag sensor assembly and occupant detection ECU.


b.

Check that the connectors (on the airbag sensor assembly side and occupant detection ECU side) are not damaged.


Result:
Proceed to
Connectors are not deformed or damaged (for RHD)
Connectors are not deformed or damaged (for LHD)
Connectors are deformed or damaged (for RHD)
Connectors are deformed or damaged (for LHD)



Connectors are not deformed or damaged (for RHD)

5.CHECK OCCUPANT DETECTION ECU CIRCUIT

Connectors are not deformed or damaged (for LHD)

8.CHECK OCCUPANT DETECTION ECU CIRCUIT

Connectors are deformed or damaged (for RHD)

REPLACE FRONT SEAT WIRE LH OR FLOOR WIRE

Connectors are deformed or damaged (for LHD)

REPLACE FRONT SEAT WIRE RH OR FLOOR WIRE

5.CHECK OCCUPANT DETECTION ECU CIRCUIT
a.
C350418C01
0.615,1.948 0.99,2.146 0.375,0.198 0.469,3.708 0.844,3.906 0.375,0.198 1.854,2.156 2.448,1.896 true 1.604,2.302 2.385,2.688 true 2.167,3.76 2.531,3.469 true 2.156,3.958 2.552,4.031 true 2.292,4.354 2.563,4.438 true 2.229,0.5 2.385,0.698 0.156,0.198 10 false A 1.927,0.698 2.083,0.896 0.156,0.198 10 false B 1.667,0.698 1.823,0.896 0.156,0.198 10 false C 1.542,0.698 1.698,0.896 0.156,0.198 10 false D 1.24,0.698 1.396,0.896 0.156,0.198 10 false E 0.938,0.49 1.094,0.688 0.156,0.198 10 false F 0.813,0.813 1.125,1.01 0.313,0.198 10 false *1 2.385,1.198 2.698,1.396 0.313,0.198 10 false *2 1.635,1.604 1.948,1.802 0.313,0.198 10 false *3 1.656,3.01 1.969,3.208 0.313,0.198 10 false *4 2.615,4.385 2.927,4.583 0.313,0.198 10 false *5 1.177,1.385 1.49,1.583 0.313,0.198 10 false *a 1.24,2.802 1.552,3 0.313,0.198 10 false *b 0.677,1.969 1.135,2.167 0.458,0.198 10 false T10 0.542,3.729 1,3.927 0.458,0.198 10 false N40 2.5,1.823 3.115,2.021 0.615,0.198 10 false FSR- 2.438,2.625 3.052,2.823 0.615,0.198 10 false FSR+ 2.583,3.385 3.198,3.583 0.615,0.198 10 false FSL+ 2.615,3.979 3.229,4.177 0.615,0.198 10 false FSL-
*1 Occupant Detection ECU
*2 Airbag Sensor Assembly
*3 Connector E
*4 Connector B
*5 Service Wire
*a Front view of wire harness connector
(to Occupant Detection ECU)
*b Rear view of wire harness connector
(to Airbag Sensor Assembly)


Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
T10-8 (FSR+) - Body ground Ignition switch ON Below 1 V
T10-4 (FSR-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 9 (FSL+) and 17 (FSL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T10-8 (FSR+) - T10-4 (FSR-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T10-8 (FSR+) - T10-4 (FSR-) Always 1 MΩ or higher
T10-8 (FSR+) - Body ground Always 1 MΩ or higher
T10-4 (FSR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK DTC

NG

7.CHECK FRONT SEAT WIRE LH
6.CHECK DTC
a.
C244238C02
0.979,1.146 1.292,1.302 0.313,0.156 10 false *1 2,1.51 2.313,1.667 0.313,0.156 10 false *2
*1 Occupant Detection ECU
*2 Airbag Sensor Assembly


Connect the connectors to the airbag sensor assembly and occupant detection ECU.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type C)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type C)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1650/32 is not output
DTC B1650/32 is output


HINT:

Codes other than DTC B1650/32 may be output at this time, but they are not related to this check.




DTC B1650/32 is output

DTC B1650/32 is not output

7.CHECK FRONT SEAT WIRE LH
a.
C350419C01
0.563,1.979 0.958,2.188 0.396,0.208 0.49,3.656 0.885,3.865 0.396,0.208 1.792,2.115 2.385,1.875 true 0.938,2.469 1.531,2.229 true 1.958,4.031 2.625,4.333 true 1.948,3.688 2.604,3.385 true 1.917,2.698 2.281,2.771 true 1.208,0.292 1.521,0.49 0.313,0.198 10 false *1 1.719,0.292 2.031,0.49 0.313,0.198 10 false *2 0.646,0.792 0.958,0.99 0.313,0.198 10 false *3 2.385,1.198 2.698,1.396 0.313,0.198 10 false *4 1.594,1.531 1.906,1.729 0.313,0.198 10 false *6 1.031,1.354 1.344,1.552 0.313,0.198 10 false *a 1.615,3.115 1.927,3.313 0.313,0.198 10 false *7 1.188,2.969 1.5,3.167 0.313,0.198 10 false *b 0.563,2.385 1.177,2.583 0.615,0.198 10 false FSR+ 2.656,3.281 3.271,3.479 0.615,0.198 10 false FSR+ 2.427,1.792 3.042,1.99 0.615,0.198 10 false FSR- 2.698,4.271 3.313,4.469 0.615,0.198 10 false FSR- 0.646,2 1.104,2.198 0.458,0.198 10 false T10 0.563,3.677 1.021,3.875 0.458,0.198 10 false NT2 2.208,0.49 2.365,0.688 0.156,0.198 10 false A 1.427,0.698 1.583,0.896 0.156,0.198 10 false D 1.896,0.698 2.052,0.896 0.156,0.198 10 false B 1.604,0.698 1.76,0.896 0.156,0.198 10 false C 1.115,0.708 1.271,0.906 0.156,0.198 10 false E 0.792,0.365 0.948,0.563 0.156,0.198 10 false F 2.313,2.698 2.625,2.896 0.313,0.198 10 false *5
*1 Front Seat Wire LH
*2 Floor Wire
*3 Occupant Detection ECU
*4 Airbag Sensor Assembly
*5 Service Wire
*6 Connector E
*7 Connector D
*a Front view of wire harness connector
(to Occupant Detection ECU)
*b Front view of wire harness connector
(to Floor Wire)


Disconnect the front seat wire LH connector from the floor wire.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
NT2-1 (FRS+) - Body ground Ignition switch ON Below 1 V
NT2-4 (FRS-) - Body ground Ignition switch ON



e.

Turn the ignition switch off.


f.

Connect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Using a service wire, connect terminals 8 (FSR+) and 4 (FSR-) of connector E.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
NT2-1 (FRS+) - NT2-4 (FRS-) Always Below 1 Ω



i.

Disconnect the service wire from connector E.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
NT2-1 (FRS+) - NT2-4 (FRS-) Always 1 MΩ or higher
NT2-1 (FRS+) - Body ground Always
NT2-4 (FRS-) - Body ground Always



Result:
Proceed to
OK
NG



OK

REPLACE FRONT SEAT WIRE LH

NG

REPLACE FLOOR WIRE

8.CHECK OCCUPANT DETECTION ECU CIRCUIT
a.
C354991C01
0.583,2.135 0.938,2.354 0.354,0.219 0.552,3.677 0.906,3.896 0.354,0.219 2.531,3.448 1.365,3.75 true 1.385,3.99 2.344,4.448 true 1.177,4.365 0.833,4.458 true 2.479,1.854 1.844,2.135 true 2.438,2.688 1.604,2.302 true 1.938,0.927 2.094,1.125 0.156,0.198 10 false B 1.677,0.927 1.833,1.125 0.156,0.198 10 false C 1.552,0.927 1.708,1.125 0.156,0.198 10 false D 1.25,0.927 1.406,1.125 0.156,0.198 10 false E 0.948,0.719 1.104,0.917 0.156,0.198 10 false F 2.24,0.719 2.396,0.917 0.156,0.198 10 false A 2.406,1.021 2.719,1.219 0.313,0.198 10 false *2 0.74,1 1.052,1.198 0.313,0.198 10 false *1 1.698,1.594 2.01,1.792 0.313,0.198 10 false *3 1.656,3.01 1.969,3.208 0.313,0.198 10 false *4 0.646,4.396 0.958,4.594 0.313,0.198 10 false *5 1.302,1.406 1.615,1.604 0.313,0.198 10 false *a 1.229,2.844 1.542,3.042 0.313,0.198 10 false *b 2.594,3.375 3.208,3.573 0.615,0.198 10 false FSR+ 2.417,4.385 3.031,4.583 0.615,0.198 10 false FSR- 0.646,2.167 1.104,2.365 0.458,0.198 10 false S10 0.604,3.698 1.063,3.896 0.458,0.198 10 false N41 2.51,2.615 3.125,2.813 0.615,0.198 10 false FSR+ 2.531,1.771 3.146,1.969 0.615,0.198 10 false FSR-
*1 Occupant Detection ECU
*2 Airbag Sensor Assembly
*3 Connector E
*4 Connector B
*5 Service Wire
*a Front view of wire harness connector
(to Occupant Detection ECU)
*b Rear view of wire harness connector
(to Airbag Sensor Assembly)


Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
S10-8 (FSR+) - Body ground Ignition switch ON Below 1 V
S10-4 (FSR-) - Body ground



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 16 (FSR+) and 24 (FSR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S10-8 (FSR+) - S10-4 (FSR-) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S10-8 (FSR+) - S10-4 (FSR-) Always 1 MΩ or higher
S10-8 (FSR+) - Body ground
S10-4 (FSR-) - Body ground



Result:
Proceed to
OK
NG



OK

9.CHECK DTC

NG

10.CHECK FRONT SEAT WIRE RH
9.CHECK DTC
a.
C244238C02
0.979,1.146 1.292,1.302 0.313,0.156 10 false *1 2,1.51 2.313,1.667 0.313,0.156 10 false *2
*1 Occupant Detection ECU
*2 Airbag Sensor Assembly


Connect the connectors to the airbag sensor assembly and occupant detection ECU.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type C)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type C)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1650/32 is not output
DTC B1650/32 is output


HINT:

Codes other than DTC B1650/32 may be output at this time, but they are not related to this check.




DTC B1650/32 is output

DTC B1650/32 is not output

10.CHECK FRONT SEAT WIRE RH
a.
C350419C02
0.563,1.979 0.958,2.188 0.396,0.208 0.49,3.656 0.885,3.865 0.396,0.208 1.792,2.115 2.385,1.875 true 0.938,2.469 1.531,2.229 true 1.958,4.031 2.625,4.333 true 1.948,3.688 2.604,3.385 true 1.917,2.698 2.281,2.771 true 1.208,0.292 1.521,0.49 0.313,0.198 10 false *1 1.719,0.292 2.031,0.49 0.313,0.198 10 false *2 0.646,0.792 0.958,0.99 0.313,0.198 10 false *3 2.385,1.198 2.698,1.396 0.313,0.198 10 false *4 1.594,1.531 1.906,1.729 0.313,0.198 10 false *6 1.031,1.354 1.344,1.552 0.313,0.198 10 false *a 1.615,3.115 1.927,3.313 0.313,0.198 10 false *7 1.188,2.969 1.5,3.167 0.313,0.198 10 false *b 0.563,2.385 1.177,2.583 0.615,0.198 10 false FSR+ 2.656,3.281 3.271,3.479 0.615,0.198 10 false FSR+ 2.427,1.792 3.042,1.99 0.615,0.198 10 false FSR- 2.698,4.271 3.313,4.469 0.615,0.198 10 false FSR- 0.646,2 1.104,2.198 0.458,0.198 10 false S10 0.563,3.677 1.021,3.875 0.458,0.198 10 false NS2 2.208,0.49 2.365,0.688 0.156,0.198 10 false A 1.427,0.698 1.583,0.896 0.156,0.198 10 false D 1.896,0.698 2.052,0.896 0.156,0.198 10 false B 1.604,0.698 1.76,0.896 0.156,0.198 10 false C 1.115,0.708 1.271,0.906 0.156,0.198 10 false E 0.792,0.365 0.948,0.563 0.156,0.198 10 false F 2.313,2.698 2.625,2.896 0.313,0.198 10 false *5
*1 Front Seat Wire RH
*2 Floor Wire
*3 Occupant Detection ECU
*4 Airbag Sensor Assembly
*5 Service Wire
*6 Connector E
*7 Connector D
*a Front view of wire harness connector
(to Occupant Detection ECU)
*b Front view of wire harness connector
(to Floor Wire)


Disconnect the front seat wire RH connector from the floor wire.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
NS2-1 (FRS+) - Body ground Ignition switch ON Below 1 V
NS2-4 (FRS-) - Body ground Ignition switch ON



e.

Turn the ignition switch off.


f.

Connect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Using a service wire, connect terminals 8 (FSR+) and 4 (FSR-) of connector E.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
NS2-1 (FRS+) - NS2-4 (FRS-) Always Below 1 Ω



i.

Disconnect the service wire from connector E.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
NS2-1 (FRS+) - NS2-4 (FRS-) Always 1 MΩ or higher
NS2-1 (FRS+) - Body ground Always
NS2-4 (FRS-) - Body ground Always



Result:
Proceed to
OK
NG



OK

REPLACE FRONT SEAT WIRE RH

NG

REPLACE FLOOR WIRE