Home › Vehicle Interior › HEATING / AIR CONDITIONING › COMPRESSOR(for 1KD-FTV, 2KD-FTV) › from 2016.08
RM3250E _58 Vehicle Interior _038073 HEATING / AIR CONDITIONING _0185863 COMPRESSOR(for 1KD-FTV, 2KD-FTV) A

HEATING / AIR CONDITIONING  COMPRESSOR(for 1KD-FTV, 2KD-FTV)  REASSEMBLY  


PROCEDURE

Hide 88410 1.INSTALL MAGNET CLUTCH ASSEMBLY

a.
E320631C02
0.052,0.094 0.323,0.396 0.271,0.302 12 false *A 0.094,2.573 0.365,2.854 0.271,0.281 12 false *B
*A w/o Thermostat, for Type A
*B w/ Thermostat


Clamp the compressor assembly in a vise between aluminum plates.


b.

Install the magnet clutch stator with the parts aligned as shown in the illustration.


c.

Using a snap ring expander, install a new snap ring with the chamfered side facing outward.

E320632C02
0.052,0.052 0.333,0.25 0.281,0.198 12 false *A 3.708,0.052 3.927,0.281 0.219,0.229 12 false *B 0.948,0.354 1.26,0.51 0.313,0.156 10 false *a 0.521,0.375 0.833,0.531 0.313,0.156 10 false *b 1.292,0.375 1.604,0.531 0.313,0.156 10 false *c 4.115,0.396 4.427,0.552 0.313,0.156 10 false *b 4.51,0.375 4.823,0.531 0.313,0.156 10 false *a 4.896,0.385 5.208,0.542 0.313,0.156 10 false *c
*A w/o Thermostat, for Type A *B w/ Thermostat
*a Chamfered Side *b Inside
*c Outside - -


NOTICE:

When installing the snap ring, do not widen it excessively.



d.

Using a snap ring expander, install the magnet clutch rotor and a new snap ring with the chamfered side facing outward.

E320633C02
0.083,0.052 0.323,0.229 0.24,0.177 12 false *A 3.708,0.073 3.979,0.271 0.271,0.198 12 false *B 0.927,0.375 1.24,0.531 0.313,0.156 10 false *a 0.5,0.406 0.813,0.563 0.313,0.156 10 false *b 1.281,0.396 1.594,0.552 0.313,0.156 10 false *c 4.125,0.396 4.438,0.552 0.313,0.156 10 false *b 4.5,0.375 4.813,0.531 0.313,0.156 10 false *a 4.917,0.385 5.229,0.542 0.313,0.156 10 false *c
*A w/o Thermostat, for Type A *B w/ Thermostat
*a Chamfered Side *b Inside
*c Outside - -


NOTICE:
·

Do not damage the seal cover of the bearing when installing the snap ring.

·

When installing the snap ring, do not widen it excessively.




e.

Install the magnet clutch washer(s) and magnet clutch hub.

NOTICE:

Do not change the combination of the magnet clutch washer(s) used before disassembly.



f.
E320634C02
0.99,2.76 1.354,2.76 true 0.979,0.323 1.344,0.323 true 0.052,0.052 0.385,0.281 0.333,0.229 12 false *A 0.073,2.458 0.344,2.76 0.271,0.302 12 false *B 1.375,0.219 1.688,0.375 0.313,0.156 10 false *a 1.385,2.667 1.698,2.823 0.313,0.156 10 false *a
*A w/o Thermostat, for Type A
*B w/ Thermostat
*a SST


Using SST, hold the magnet clutch hub and install the bolt.

SST
09985-00040  

Torque:
13.2 N*m (135 kgf*cm, 10 ft.*lbf)

NOTICE:

Make sure that there is no foreign matter or oil on the compressor shaft, bolt and magnet clutch hub.



Hide 2.INSPECT MAGNET CLUTCH CLEARANCE

a.
E320635C02
0.052,0.073 0.292,0.313 0.24,0.24 12 false *A 0.094,2.5 0.323,2.729 0.229,0.229 12 false *B
*A w/o Thermostat, for Type A
*B w/ Thermostat


Set a dial indicator to the magnet clutch hub.


b.

Connect a battery positive lead to terminal 1 of the magnet clutch connector and a negative lead to the ground wire. Turn the magnet clutch on and off and measure the clearance.

Standard Clearance:
w/o Thermostat, for Type A:

0.35 to 0.60 mm (0.0138 to 0.0236 in.)

w/ Thermostat:

0.25 to 0.50 mm (0.0098 to 0.0197 in.)


If the measured value is not within the standard clearance, remove the magnet clutch hub and adjust the clearance using magnet clutch washers to obtain the standard clearance.

Magnet Clutch Washer Thickness:

0.1 mm (0.00394 in.)

0.3 mm (0.0118 in.)

0.5 mm (0.0197 in.)


NOTICE:

Adjustment should be performed with 3 or fewer magnet clutch washers.



c.

Remove the compressor assembly with magnet clutch from the vise.


Hide 88688N 3.INSTALL COOLER BRACKET

a.
E320626C03
0.052,0.052 0.354,0.271 0.302,0.219 12 false *A 0.083,2.396 0.292,2.625 0.208,0.229 12 false *B
*A w/o Thermostat, for Type A
*B w/ Thermostat


Install the cooler bracket with the screw.


b.

w/ Thermostat:

Attach the clamp.


c.

w/ Thermostat:

Connect the connector.