Home › Engine / Hybrid System › 2TR-FE FUEL › FUEL PUMP(for Short Wheelbase) › from 2016.08
RM3250E _51 Engine / Hybrid System _038023 2TR-FE FUEL _0193803 FUEL PUMP(for Short Wheelbase) A

2TR-FE FUEL  FUEL PUMP(for Short Wheelbase)  INSTALLATION  


PROCEDURE

Hide 77020A 1.INSTALL FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

a.

Apply a light coat of gasoline or grease to a new fuel suction tube set gasket, and install it to the fuel tank assembly.


b.

Install the fuel suction with pump and gauge tube assembly to the fuel tank assembly.

NOTICE:

Be careful not to bend the arm of the fuel sender gauge.



c.
A346230C01
1.896,1.75 0.375,1.229 0.375,1.229 1.656,0.344 true 0.198,1.135 0.354,1.344 0.156,0.208 10 true *a
*a Protrusion
V100135

Hole


Align the protrusions of the fuel suction with pump and gauge tube assembly with the holes in the fuel tank assembly.


d.

While pressing down on the fuel suction with pump and gauge tube assembly, temporarily install the fuel pump gauge retainer.


e.
A391907C02
0.5,3.167 0.646,3.167 0.646,3.167 0.906,2.781 true 2.75,1.865 2.531,2.344 2.531,2.344 2.385,2.344 true 1,2.417 1.729,3.094 1.729,3.094 1.896,3.094 true 2.177,2.24 2.438,2.438 0.26,0.198 10 false *a 1.979,3.01 2.25,3.198 0.271,0.188 10 false *b 0.292,3.073 0.51,3.271 0.219,0.198 10 false *c
*a SST (Plate)
*b SST (Claw)
*c Insertion Point
V100135

SST (Bolt)


Set the 2 claws, 2 bolts and plate of SST on the fuel pump gauge retainer.

SST
09808-14031  (09808-01010, 09808-01020, 09808-01030, 09808-01090)
09808-01071  

HINT:

Securely insert the ends of SST into the insertion points in the fuel pump gauge retainer.



f.

While firmly pressing the claws of SST into the insertion points in the fuel pump gauge retainer, tighten the bolts of the claws.


g.
A387333C01
2.75,2.229 2.75,1.99 true 0.927,0.167 1.156,0.167 1.156,0.167 1.271,0.594 true 0.875,0.771 1.104,0.771 1.104,0.771 1.229,1.042 true 1.115,3.875 1.51,3.688 false 1.281,4.083 1.5,3.698 false 0.438,3.833 0.656,3.833 0.656,3.833 0.792,4.021 false 1.104,4.479 1.135,4.25 true 1.104,4.479 0.958,4.021 true 1.531,3.594 1.844,3.75 0.313,0.156 10 false *a 1.031,4.5 1.344,4.656 0.313,0.156 10 true *b 2.646,2.24 2.906,2.396 0.26,0.156 10 true *c 0.583,0.052 0.969,0.229 0.385,0.177 10 true SST 0.531,0.677 0.917,0.854 0.385,0.177 10 true SST 0.26,3.74 0.49,3.948 0.229,0.208 10 true *a
*a Alignment Mark
*b Groove
*c Insertion Point
V100135

Turn
V100136

Front of Vehicle


Attach the handle of SST.


h.

Check once more that the tip of SST is securely inserted into the insertion area of the fuel pump gauge retainer as shown in the illustration.


i.

Using SST, rotate the fuel pump gauge retainer so that the protrusions of the retainer are aligned with the grooves in the fuel tank assembly to install the fuel suction tube assembly with pump and gauge to the fuel tank assembly.

NOTICE:
·

Do not use any tools other than SST, such as a screwdriver, etc.

·

Do not use excessive force when pressing down on SST, as the fuel pump gauge retainer will place excessive force on the fuel suction tube assembly with pump and gauge and be difficult to install, and parts may be damaged.

·

Be sure to keep the handle level when turning it, as SST may slip off the retainer if the handle is turned at an angle with excessive force.

·

Do not use an impact wrench or turn the handle with excessive force, as parts may be damaged.

·

If SST slips off the fuel pump gauge retainer, loosen the bolts and reattach SST to the fuel pump gauge retainer.

·

Make sure that the fuel suction tube set gasket does not come off.




j.

Insert the fuel tank main tube sub-assembly and fuel tank return tube into the plugs of the fuel suction with pump and gauge tube assembly and fix them in place with the 2 tube joint clips.

NOTICE:
A346233C02
1.667,1.969 2.052,1.969 false 1.479,2.25 1.865,2.25 false 1.25,2.573 1.49,2.573 1.49,2.573 1.625,2.417 false 2.396,2.531 2.75,2.646 2.75,2.646 2.396,2.406 true 0.594,4.115 0.771,4.115 0.771,4.115 1.01,3.698 true 2.01,4.052 2.188,4.052 2.188,4.052 2.427,3.635 true 1.479,1.875 1.698,2.052 0.219,0.177 10 false *c 1.292,2.167 1.49,2.344 0.198,0.177 10 false *1 2.792,2.604 3.031,2.792 0.24,0.188 10 false *d 1.063,2.49 1.271,2.677 0.208,0.188 10 false *2 0.688,3.188 0.885,3.406 0.198,0.219 10 false *a 2.167,3.229 2.417,3.438 0.25,0.208 10 false *b 0.417,4.031 0.594,4.219 0.177,0.188 10 false *e 1.823,3.958 2,4.167 0.177,0.208 10 false *e
*1 Tube Joint Clip
*2 Fuel Suction Plate Sub-assembly
*a CORRECT
*b INCORRECT
*c Fuel Tube Joint
*d O-Ring
*e Collar


·

Check that there are no scratches or foreign objects on the connecting parts.

·

Check that the fuel tube joints are inserted securely.

·

Check that the tube joint clips are on the collars of the fuel tube joints.

·

After installing the tube joint clips, check that the fuel tube joints cannot be pulled off.

·

Be careful not to damage any clips.

If a clip is damaged, replace it.