Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › from 2016.08
RM3250E _56 Audio / Visual / Telematics _038052 AUDIO / VIDEO _0182296 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Vehicle Speed Signal Circuit between Radio Receiver and Combination Meter  


DESCRIPTION

The radio and display receiver assembly receives a vehicle speed signal from the combination meter assembly to control the ASL function.

HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls its respective system based on this pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the diagram below will not operate normally.



WIRING DIAGRAM

E353848E02
5.135,7.219 6.833,7.604 1.698,0.385 10 false Radio and Display Receiver Assembly 5.354,4.333 6.958,4.615 1.604,0.281 10 false Telematics Transceiver*8 5.354,4.146 5.833,4.333 0.479,0.188 10 false G130 5.135,7.052 5.521,7.219 0.385,0.167 10 false G37 5.531,2.563 5.917,2.74 0.385,0.177 10 false G27 5.563,2.75 6.49,2.948 0.927,0.198 10 false Body ECU*7 5.229,1.292 7.156,1.51 1.927,0.219 10 false Combination Meter Assembly 5.219,1.135 5.531,1.302 0.313,0.167 10 false G9 0.844,1.188 1.24,1.365 0.396,0.177 10 false ECM 1.219,2.042 1.615,2.219 0.396,0.177 10 false SPD 1.208,0.552 1.604,0.729 0.396,0.177 10 false SPD 5.635,2.021 6.031,2.198 0.396,0.177 10 false SPD 5.615,3.583 6.094,3.771 0.479,0.188 10 false SPDP 5.635,6.698 6.031,6.875 0.396,0.177 10 false SPD 1.156,3.625 1.635,3.813 0.479,0.188 10 false SPD1 5.615,0.635 5.927,0.802 0.313,0.167 10 false +S 0.469,2.771 3.625,2.958 3.156,0.188 10 false Certification ECU (Smart Key ECU Assembly)*5 0.74,4.406 1.667,4.583 0.927,0.177 10 false TCM*4, *6 0.531,4.198 0.917,4.375 0.385,0.177 10 false G90 0.469,2.604 0.854,2.781 0.385,0.177 10 false G69 1.667,0.708 2.021,0.885 0.354,0.177 10 false G88 2.094,0.719 2.448,0.896 0.354,0.177 10 false G45 2.531,0.719 2.885,0.896 0.354,0.177 10 false G85 2.979,0.729 3.333,0.906 0.354,0.177 10 false G83 1.708,0.469 1.948,0.646 0.24,0.177 10 false 12 2.135,0.49 2.375,0.667 0.24,0.177 10 false 23 2.583,0.479 2.823,0.656 0.24,0.177 10 false 10 3.021,0.49 3.26,0.667 0.24,0.177 10 false 17 1.74,0.99 1.927,1.177 0.188,0.188 10 false *1 2.125,0.99 2.313,1.177 0.188,0.188 10 false *2 2.563,1 2.75,1.188 0.188,0.188 10 false *3 3.01,1.01 3.198,1.198 0.188,0.188 10 false *4 1.677,2.021 1.833,2.219 0.156,0.198 10 false 7 1.677,3.625 1.896,3.802 0.219,0.177 10 false 25 5.396,2.01 5.552,2.208 0.156,0.198 10 false 5 5.292,0.615 5.51,0.792 0.219,0.177 10 false 19 5.323,3.563 5.542,3.74 0.219,0.177 10 false 10 5.344,6.688 5.583,6.865 0.24,0.177 10 false 17 0.167,5.25 1.208,5.438 1.042,0.188 10 false *1: for 1GR-FE 1.438,5.25 3.083,5.438 1.646,0.188 10 false *2: for 1TR-FE, 2TR-FE 0.177,5.573 2,5.75 1.823,0.177 10 false *3: for 1GD-FTV, 2GD-FTV 2,5.563 3.76,5.75 1.76,0.188 10 false *4: for 1KD-FTV, 2KD-FTV 0.167,5.885 2.25,6.083 2.083,0.198 10 false *5: w/ Entry and Start System 0.167,6.25 2.25,6.5 2.083,0.25 10 false *6: for Automatic Transmission 0.167,6.563 3.635,6.75 3.469,0.188 10 false *7: w/ Speed-sensitive Automatic Door Lock Function 0.167,6.885 2.25,7.083 2.083,0.198 10 false *8: w/ Telematics Transceiver 5.375,5.156 5.615,5.333 0.24,0.177 10 false 2 5.646,5.156 6.042,5.333 0.396,0.177 10 false SPD 5.26,5.771 6.948,6.24 1.688,0.469 10 false Tire Pressure Warning ECU and Receiver*9 5.25,5.583 5.635,5.75 0.385,0.167 10 false N32 0.167,7.25 3.031,7.479 2.865,0.229 10 false *9: w/ Tire Pressure Warning System

CAUTION / NOTICE / HINT

NOTICE:

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.


PROCEDURE

1.CHECK COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
a.
E256135C35
1.479,0.438 1.896,0.656 0.417,0.219 0.656,1.802 0.865,1.333 true 0.167,0.198 0.479,0.396 0.313,0.198 10 false *a 1.594,0.479 1.906,0.677 0.313,0.198 10 false G9 0.469,1.833 0.781,2.031 0.313,0.198 10 false +S 2.792,3.594 3.188,3.865 0.396,0.271 10 false GND 1.083,3.896 1.479,4.167 0.396,0.271 10 false (A)
*a Component with harness connected
(Combination Meter Assembly)


Check the output waveform.

i.

Remove the combination meter assembly with the connector still connected.


ii.

Connect an oscilloscope to terminal G9-19 (+S) and body ground.


iii.

Turn the ignition switch to ON.


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal G9-19 (+S) - Body ground
Tool setting 5 V/DIV, 20 ms./DIV
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)

*1: for 1GR-FE

*2: for 1TR-FE, 2TR-FE

*3: for 1GD-FTV, 2GD-FTV

*4: for 1KD-FTV, 2KD-FTV

*5: w/ Entry and Start System

*6: w/ Speed-sensitive Automatic Door Lock Function

*7: for Automatic Transmission

*8: w/ Telematics Transceiver

*9: w/ Tire Pressure Warning System


a.

Disconnect the G37 radio and display receiver assembly connector.


b.

Disconnect the G9 combination meter assembly connector.


c.

Disconnect the G88*1, G45*2, G85*3 or G83*4 ECM connector.


d.

Disconnect the G69 certification ECU (smart key ECU assembly) connector.*5


e.

Disconnect the G27 body ECU connector.*6


f.

Disconnect the G90 TCM connector.*4, *7


g.

Disconnect the G130 telematics transceiver connector.*8


h.

Disconnect the N32 tire pressure warning ECU and receiver connector.*9


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G37-17 (SPD) - G9-19 (+S) Always Below 1 Ω
G37-17 (SPD) or G9-19 (+S) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR