Use the following procedure to troubleshoot the audio and visual system.
*: Use the GTS.
| Proceed to |
|---|
| NEXT |
NEXT
When troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.
Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.
The following 5 items are important points for problem analysis:
| What | Vehicle model, system name |
| When | Date, time, occurrence frequency |
| Where | Road conditions |
| Under what conditions? | Driving conditions, weather conditions |
| How did it happen? | Problem symptoms |
| Proceed to |
|---|
| NEXT |
NEXT
Measure the battery voltage.
11 to 14 V
If the voltage is below 11 V, recharge or replace the battery before proceeding.
| Proceed to |
|---|
| NEXT |
NEXT
Check that condensation is not likely to occur in the cabin and that the temperature is not high or extremely low in the cabin.
Condensation is not likely being produced and the temperature is not high or extremely low.
A humid cabin and a rapid change in temperature may lead to condensation. Condensation in the cabin may cause a short circuit.
The audio and visual system may not operate normally when the temperature is -20°C (-4°F) or lower, or 65°C (149°F) or higher.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check if CAN communication system DTCs are output.
for LHD with Central Gateway ECU:
for LHD without Central Gateway ECU:
for RHD with Central Gateway ECU:
for RHD without Central Gateway ECU:
| Result | Proceed to |
|---|---|
| CAN DTCs are not output. | A |
| CAN DTCs are output. | B |
A
B
for LHD with Central Gateway ECU:
for LHD without Central Gateway ECU:
for RHD with Central Gateway ECU:
for RHD without Central Gateway ECU:
Check for DTCs and note any codes that are output.
Clear the DTCs.
Recheck for DTCs by simulating the operation indicated by the DTCs.
| Result | Proceed to |
|---|---|
| DTCs are output. | A |
| DTCs are not output. | B |
A
B
*1: w/ Rear View Monitor System (for Radio and Display Type)
*2: w/ Telematics Transceiver
Find the output code in Diagnostic Trouble Code Chart.
The audio and visual system outputs DTCs for the following system.
When DTCs other than those in Diagnostic Trouble Code Chart for the navigation system are output, refer to Diagnostic Trouble Code Chart for the relevant system.
Refer to Rear View Monitor System (for Radio and Display Type)*1.
Refer to Telematics System*2
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
| Result | Proceed to |
|---|---|
| DTCs for the audio and visual system are output. | A |
| DTCs for the rear view monitor system (for Radio and Display Type) are output.*1 | B |
| DTCs for the telematics system are output.*2 | C |
A
B
C
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Refer to Problem Symptoms Table.
| Result | Proceed to |
|---|---|
| Fault is not listed in Problem Symptoms Table. | A |
| Fault is listed in Problem Symptoms Table. | B |
If the symptoms do not recur and no DTCs are output, attempt to reproduce the symptoms.
A
B
Terminals of ECU.
Data List / Active Test
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
After clearing DTCs, recheck for DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT