Home › Engine / Hybrid System › 2GD-FTV EMISSION CONTROL › EGR VALVE(w/o EGR Cooler) › from 2016.08
RM3250E _51 Engine / Hybrid System _038008 2GD-FTV EMISSION CONTROL _0290055 EGR VALVE(w/o EGR Cooler) A

2GD-FTV EMISSION CONTROL  EGR VALVE(w/o EGR Cooler)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the EGR valve removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Replacement of diesel throttle body assembly Perform initialization - (Click here)
Replacement of electric EGR control valve assembly Perform initialization - (Click here)

CAUTION:
A343692

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


PROCEDURE

Hide 26100G 2.REMOVE DIESEL THROTTLE BODY ASSEMBLY

Hide 16278 3.REMOVE NO. 2 WATER BY-PASS PIPE

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A344435C01
0.063,1.958 0.26,2.125 0.198,0.167 10 true *1 0.021,0.688 0.219,0.854 0.198,0.167 10 true *2 2.938,0.698 3.135,0.865 0.198,0.167 10 true *3 2.302,2.5 2.5,2.667 0.198,0.167 10 true *4 3.188,0.781 3.385,0.948 0.198,0.167 10 true *3
*1 No. 13 Water By-pass Hose
*2 No. 15 Water By-pass Hose
*3 Heater Hose
*4 No. 16 Water By-pass Hose


Slide the clamp and disconnect the No. 2 water by-pass pipe from the No. 13 water by-pass hose.


b.

Slide the clamp and disconnect the No. 15 water by-pass hose from the water by-pass pipe.


c.

Slide the 2 clamps and disconnect the 2 heater hoses from the No. 2 water by-pass pipe.


d.

Slide the clamp and disconnect the No. 16 water by-pass hose from the EGR pipe stay.


e.

Remove the 4 bolts and No. 2 water by-pass pipe from the cylinder head cover sub-assembly, No. 3 water by-pass pipe sub-assembly and No. 2 engine cover bracket.


Hide 23265C 4.REMOVE GAS FILTER

a.
A369950

Disconnect the 2 vacuum hoses from the turbo pressure sensor and intake manifold.


b.

Remove the gas filter from the gas filter bracket.


Hide 89421C 5.REMOVE TURBO PRESSURE SENSOR

a.
A369951

Disconnect the connector from the turbo pressure sensor.


b.

Remove the bolt and turbo pressure sensor from the No. 3 water by-pass pipe sub-assembly.


Hide 44763C 6.REMOVE NO. 2 HOSE TO HOSE TUBE

a.
A343888

Slide the clamp to disconnect the union to connector tube hose from the No. 1 hose to hose tube.


b.

Slide the clamp to disconnect the union to check valve hose from the vacuum pump assembly.


c.

Remove the 2 bolts and No. 2 hose to hose tube from the cylinder head cover sub-assembly and hose bracket.


Hide 12632 7.REMOVE NO. 2 ENGINE COVER BRACKET

a.
A369953

Remove the 2 bolts and No. 2 engine cover bracket from the No. 3 water by-pass pipe sub-assembly and EGR valve adapter sub-assembly.


Hide 23300 8.DISCONNECT FUEL FILTER ASSEMBLY

a.
A339642N01
3.083,1 3.292,1.188 0.208,0.188 10 true 1 2.802,1.646 3.01,1.833 0.208,0.188 10 true 2

Disconnect the clamp and slide the lead wire as shown in the illustration to remove it.


b.
A344450

Disconnect the fuel filter assembly from the fuel filter support.


Hide 82121 9.DISCONNECT ENGINE WIRE

a.
A369955

Detach the 2 clamps and disconnect the 2 connectors from the turbocharger sub-assembly.


b.
A343891

Disconnect the connector from the camshaft position sensor.


c.

Disconnect the 4 connectors from the 4 injector assemblies.


d.

Disconnect the connector from the electric EGR control valve assembly.


e.

Disconnect the connector from the glow plug connector.


f.

Disconnect the connector from the sensor wire of common rail assembly.


g.

Detach the clamp and remove the bolt.


h.
A369957

Detach the clamp and disconnect the connector from the power steering oil pressure switch.


i.

Detach the clamp and remove the bolt.


Hide 25625 10.REMOVE EGR VALVE BRACKET

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A343894

Remove the bolt, nut and EGR valve bracket from the electric EGR control valve assembly and intake manifold.


Hide 25612 11.REMOVE NO. 2 EGR PIPE

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A369958

Remove the bolt, 4 nuts and No. 2 EGR pipe from the electric EGR control valve assembly and intake manifold.


b.

Remove the 2 gaskets.


Hide 25800 12.REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A343896

Detach the clamp and disconnect the connector from the common rail assembly.


b.
A343897

Slide the clamp and disconnect the No. 9 water by-pass hose from the electric EGR control valve assembly.


c.

Remove the 2 bolts and electric EGR control valve assembly from the EGR valve adapter sub-assembly.


d.

Remove the gasket.