Home › Vehicle Exterior › BODY WELD POINT › QUARTER LOCK PILLAR REINFORCEMENT(for Single Cab)
BM33J0E _01 Vehicle Exterior _041756 BODY WELD POINT _0194234 QUARTER LOCK PILLAR REINFORCEMENT(for Single Cab) F

BODY WELD POINT  QUARTER LOCK PILLAR REINFORCEMENT(for Single Cab)  CUT AND JOIN REPLACEMENT SECTIONS  


K123724

With the quarter panel cut and join replacement sections removed.


REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108820

Remove Weld Points
K108826

Cut with Disc Sander etc.
K108827

Cut and Join Location

K123838

K123839C01
1.76,0.458 2.073,0.615 0.313,0.156 10 false *a 4.531,1.438 4.844,1.594 0.313,0.156 10 false *b
*a 65 mm (2.56 in.) *b 120 mm (4.72 in.)


K123840


INSTALLATION


Symbol Meaning
K108820

Remove Weld Points
K108823

Plug Weld
K108825

Plug Weld
K108827

Cut and Join Location
K108830

Fillet Weld
K108831

Butt Weld

a.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.


b.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)


c.

If the entire supply part is not needed, remove the part of the supply part that is needed.

HINT:

Carefully cut the rocker panel outer so not to damage A.


K123841C01
2.542,1.729 2.667,1.25 2.667,1.25 2.833,1.25 false 2.5,2.5 2.333,2.5 2.333,2.5 2.135,1.906 false 4.75,2.417 4.583,2.417 4.583,2.417 4.385,2.094 false 5.417,3.333 5.583,3.333 5.583,3.333 5.802,3 false 2.854,1.167 3.167,1.323 0.313,0.156 10 false *1 4.792,2.333 5.104,2.49 0.313,0.156 10 false *2 5.26,3.25 5.573,3.406 0.313,0.156 10 false *3 1.656,1.25 1.969,1.406 0.313,0.156 10 false *a 3.604,0.896 3.917,1.052 0.313,0.156 10 false *b 2.552,2.417 2.865,2.573 0.313,0.156 10 false A
*1 ROCKER PANEL OUTER *2 QUARTER LOCK PILLAR REINFORCEMENT SUB-ASSEMBLY
*3 SIDE PANEL SUB-ASSEMBLY INNER - -
*a 65 mm (2.56 in.) *b 120 mm (4.72 in.)



d.

Before temporarily installing the new parts, weld the rocker panel outer, rocker extension outer, quarter lock pillar reinforcement sub-assembly and side panel sub-assembly inner with the standard number of welding points.

K123842C01
0.75,3.333 0.917,3.333 0.917,3.333 1.083,2.958 false 1.25,2.76 1.083,2.167 1.083,2.167 0.917,2.167 false 1.583,1.167 1.75,1.167 1.75,1.167 2.031,1.583 false 5.49,2.75 5.833,3.25 5.833,3.25 6,3.25 false 0.583,3.24 0.896,3.396 0.313,0.156 10 false *1 0.76,2.083 1.073,2.24 0.313,0.156 10 false *2 1.427,1.083 1.74,1.24 0.313,0.156 10 false *3 6.042,3.167 6.354,3.323 0.313,0.156 10 false *4 4.344,3.104 4.656,3.26 0.313,0.156 10 false *a
*1 ROCKER PANEL OUTER *2 ROCKER EXTENSION OUTER
*3 QUARTER LOCK PILLAR REINFORCEMENT SUB-ASSEMBLY *4 SIDE PANEL SUB-ASSEMBLY INNER
*a 10 mm (0.39 in.) - -


K123843

K123844C01
5.229,3.417 5.542,3.573 0.313,0.156 10 false *a
*a 15 mm (0.59 in.) - -



e.

After welding, apply the foamed sealing material to the corresponding parts. (See the painting/coating)


f.

After welding, apply body sealer to the corresponding parts. (See the painting/coating)


g.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.