Home › Vehicle Exterior › BODY WELD POINT › FRAME SIDE RAIL PLATE
BM33J0E _01 Vehicle Exterior _041756 BODY WELD POINT _0194242 FRAME SIDE RAIL PLATE F

BODY WELD POINT  FRAME SIDE RAIL PLATE  ASSEMBLY REPLACEMENT  


K123732

K123934

HINT:
·

Use the same procedure for the RH and LH.

·

The procedure listed below is for the RH.



REMOVAL


Symbol Meaning
K108826

Cut with Disc Sander etc.

K123935C01
5.208,2.656 5.521,2.813 0.313,0.156 10 false *A 5.573,2.281 5.885,2.438 0.313,0.156 10 false *B 3.104,0.417 3.417,0.573 0.313,0.156 10 false *C 2.76,2.146 3.073,2.302 0.313,0.156 10 false *B 3.177,2.542 3.49,2.698 0.313,0.156 10 false *C 2.698,0.813 3.01,0.969 0.313,0.156 10 false *A 2.708,4.542 3.021,4.698 0.313,0.156 10 false *A 3.083,4.906 3.396,5.063 0.313,0.156 10 false *C
*A FRONT *B UPPER
*C LH - -



INSTALLATION


Symbol Meaning
K108830

Fillet Weld

a.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)


b.

Make sure that proper welding can be performed by setting up the welding conditions as necessary before performing work.


c.

To prevent heat deformation, weld the right and left side of each part before continuing to the next part.


d.

Make sure that the welding bead at A is overlapped.

K123936C01
2.906,1.583 3.25,1.333 3.25,1.333 3.417,1.333 false 1.75,2 2,2 2,2 2.167,1.74 false 1.667,4.844 1.917,4.844 1.917,4.844 2.094,5.073 false 2.708,4.542 3.021,4.698 0.313,0.156 10 false *A 3.083,4.906 3.396,5.063 0.313,0.156 10 false *C 5.188,2.656 5.5,2.813 0.313,0.156 10 false *A 5.604,2.271 5.917,2.427 0.313,0.156 10 false *B 3.146,2.552 3.458,2.708 0.313,0.156 10 false *C 3.49,1.25 3.802,1.406 0.313,0.156 10 false *1 2.708,0.802 3.021,0.958 0.313,0.156 10 false *A 2.771,2.156 3.083,2.313 0.313,0.156 10 false *B 3.083,0.417 3.396,0.573 0.313,0.156 10 false *C 2.865,4.354 3.177,4.51 0.313,0.156 10 false *a 1.521,4.76 1.833,4.917 0.313,0.156 10 false A 1.604,1.927 1.917,2.083 0.313,0.156 10 false A
*A FRONT *B UPPER
*C LH - -
*1 FRAME SIDE RAIL PLATE SUB-ASSEMBLY - -
*a 277 mm (10.91 in.) - -



e.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.