Home › Vehicle Exterior › BODY WELD POINT › DECK MOUNTING NO.3 BRACKET
BM33J0E _01 Vehicle Exterior _041756 BODY WELD POINT _0194253 DECK MOUNTING NO.3 BRACKET F

BODY WELD POINT  DECK MOUNTING NO.3 BRACKET  ASSEMBLY REPLACEMENT  


K123745

K123974

HINT:
·

Use the same procedure for the RH and LH.

·

The procedure listed below is for the RH.



REMOVAL


Symbol Meaning
K108826

Cut with Disc Sander etc.

K123975C01
2.24,2.74 2.552,2.896 0.313,0.156 10 false *A 2.24,0.583 2.552,0.74 0.313,0.156 10 false *A 1.854,2.344 2.167,2.5 0.313,0.156 10 false *B 1.854,0.198 2.167,0.354 0.313,0.156 10 false *C
*A FRONT *B UPPER
*C LH - -



INSTALLATION


Symbol Meaning
K108830

Fillet Weld

a.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)


b.

Make sure that proper welding can be performed by setting up the welding conditions as necessary before performing work.


c.

Before installing the upper body, confirm the alignment of the upper body and frame.


d.

To prevent heat deformation, weld the right and left side of each part before continuing to the next part.

K123976C01
4.333,2.25 4.083,2.25 4.083,2.25 3.906,1.958 false 2.417,4 3.271,3.51 false 4.75,4 3.875,3.5 false 2.167,4 2.417,4 2.417,4 3.26,3.625 false 5,4 4.75,4 4.75,4 3.885,3.635 false 2.24,2.729 2.552,2.885 0.313,0.156 10 false *A 1.865,2.344 2.177,2.5 0.313,0.156 10 false *B 3.771,0.167 4.083,0.323 0.313,0.156 10 false *e 4.938,3.406 5.25,3.563 0.313,0.156 10 false *f 2.24,0.583 2.552,0.74 0.313,0.156 10 false *A 1.854,0.198 2.167,0.354 0.313,0.156 10 false *C 4.385,2.177 4.719,2.396 0.333,0.219 10 false *1 2.74,2.031 3.052,2.188 0.313,0.156 10 false *a 4.219,1.865 4.531,2.021 0.313,0.156 10 false *b 2.802,2.844 3.115,3 0.313,0.156 10 false *c 3.531,4.51 3.844,4.667 0.313,0.156 10 false *d 2.74,0.24 3.052,0.396 0.313,0.156 10 false *e 4.563,3.313 4.875,3.469 0.313,0.156 10 false *f 5.042,3.917 5.333,4.188 0.292,0.271 10 false *g 3.24,0.177 3.552,0.333 0.313,0.156 10 false *e 2.313,3.281 2.625,3.438 0.313,0.156 10 false *f 1.99,3.385 2.302,3.542 0.313,0.156 10 false *f 1.99,3.906 2.281,4.177 0.292,0.271 10 false *g
*A FRONT *B UPPER
*C LH - -
*1 BODY SUPPORT BRACKET NO.5 - -
*a 24 mm (0.94 in.) *b 51 mm (2.01 in.)
*c 82 mm (3.23 in.) *d 108 mm (4.25 in.)
*e 5 +/- 5 mm (0.20 +/- 0.20 in.) *f 0 +/- 5 mm (0 +/- 0.20 in.)
*g Welding ID Mark - -



e.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.