Home › Vehicle Exterior › BODY WELD POINT › NAME PLATE › 2015.06–2015.11
BM33J0E _01 Vehicle Exterior _041756 BODY WELD POINT _0201877 NAME PLATE F

BODY WELD POINT  NAME PLATE  ATTACHMENT POSITION  


1.

Heat the double-sided tape remaining on the body with an infrared lamp or equivalent.

HINT:

Heat the tape to 40 to 60°C for approximately 1 to 2 minutes.


2.

Wipe off the remaining double-sided tape using a clean cloth or equivalent.

NOTICE:

If a name plate is installed without thoroughly removing the remaining double-sided tape from the body, the name plate will not adhere properly. Make sure to thoroughly wipe off the double-sided tape.


3.

After cleaning the installation area of the body with degreasing agent, attach the name plate to the position shown in the illustration.

HINT:

The working environment should be 20°C when installing the name plate. If the working environment is below 20°C, heat the installation area of the body to 20 to 30°C and then install the name plate.



B414806C01
4,4.083 4.667,4.083 false 5,5.583 5.667,5.583 false 3.698,6.917 4.365,6.917 false 2.333,2.729 2,2.729 2,2.729 2,1.813 true 4.333,2.417 3.75,2.417 3.75,2.417 3.75,1.333 true 4.031,1.333 4.615,1.333 true 0.073,0.104 0.385,0.26 0.313,0.156 10 false *A 4.729,3.99 5.5,4.365 0.771,0.375 10 false (1) ●*1 2.396,2.635 3.313,3.333 0.917,0.698 10 false (1) 5.729,5.49 6.5,5.865 0.771,0.375 10 false (2) ●*2 4.427,6.823 5.198,7.198 0.771,0.375 10 false (3) ●*3 4.385,2.313 4.865,2.76 0.479,0.448 10 false (2) 4.667,1.24 5.021,1.583 0.354,0.344 10 false (3)
*A for A Deck - -
*1 NO. 2 TAIL GATE MARK *2 REAR NAME PLATE
*3 TAIL GATE MARK - -
● Non-reusable part - -


B399442C01
2.521,2.698 1.99,2.698 1.99,2.698 1.99,1.615 true 4.396,2.229 3.865,2.229 3.865,2.229 3.865,1.146 true 4.021,4.021 4.771,4.021 false 4.927,5.573 5.677,5.573 false 2.583,2.625 3.042,2.823 0.458,0.198 10 false (1) 4.448,2.156 4.906,2.354 0.458,0.198 10 false (2) 0.094,0.083 0.406,0.281 0.313,0.198 10 false *A 4.823,3.927 5.896,4.125 1.073,0.198 10 false (1) ●*1 5.729,5.5 6.802,5.698 1.073,0.198 10 false (2) ●*2
*A for J Deck - -
*1 NO. 2 TAIL GATE MARK *2 REAR NAME PLATE
● Non-reusable part - -


B410832C02
4.958,4.688 5.563,4.688 false 2.875,2.292 2.479,2.292 2.479,2.292 2.479,1.781 false 5.604,4.604 6.635,4.917 1.031,0.313 10 false (1) ●*1 2.917,2.208 3.323,2.542 0.406,0.333 10 false (1) 0.094,0.104 0.406,0.302 0.313,0.198 10 false *A
*A for A Deck - -
*1 NO. 3 TAIL GATE MARK - -
● Non-reusable part - -


B410833C02
2.75,2.208 2.479,2.208 2.479,2.208 2.479,1.729 false 4.958,4.708 5.5,4.708 false 5.542,4.625 6.615,4.823 1.073,0.198 10 false (1) ●*1 2.802,2.125 3.26,2.438 0.458,0.313 10 false (1) 0.094,0.083 0.406,0.281 0.313,0.198 10 false *A
*A for J Deck - -
*1 NO. 3 TAIL GATE MARK - -
● Non-reusable part - -


B399443C01
2.698,3.115 2.208,3.115 2.208,3.115 2.208,1.813 true 5.177,4.99 5.708,4.99 false 2.74,3.031 3.198,3.229 0.458,0.198 10 false (1) 5.771,4.906 6.844,5.104 1.073,0.198 10 false (1) ●*1
*1 FRONT DOOR NAME PLATE - -
● Non-reusable part - -


NO. 2 TAIL GATE MARK


B399447C02
0.094,0.417 0.365,0.646 0.271,0.229 10 true *A 0.135,2.854 0.365,3.073 0.229,0.219 10 true *B 0.979,0.781 1.156,0.979 0.177,0.198 10 true A 2.521,0.917 2.688,1.135 0.167,0.219 10 true B 1,3.563 1.167,3.74 0.167,0.177 10 true C 2.479,3.49 2.656,3.708 0.177,0.219 10 true D 0.104,0.083 0.375,0.313 0.271,0.229 10 true *a
*A for A Deck
*B for J Deck
*a Reference Values


Standard:
Area Specified Condition
A 24.8 mm (0.976 in.)
B 165.7 mm (6.52 in.)
C 24.5 mm (0.965 in.)
D 213.3 mm (8.398 in.)



REAR NAME PLATE


B399448C02
0.125,0.365 0.385,0.583 0.26,0.219 10 true *A 0.135,2.833 0.406,3.052 0.271,0.219 10 true *B 0.656,0.813 0.844,1.021 0.188,0.208 10 true A 0.667,3.531 0.833,3.729 0.167,0.198 10 true C 2.417,1.719 2.573,1.917 0.156,0.198 10 true B 2.396,4.469 2.552,4.667 0.156,0.198 10 true D 0.094,0.063 0.354,0.281 0.26,0.219 10 true *a
*A for A Deck
*B for J Deck
*a Reference Values


Standard:
Area Specified Condition
A 165.6 mm (6.52 in.)
B 26.5 mm (1.044 in.)
C 221.2 mm (8.709 in.)
D 26.4 mm (1.039 in.)



TAIL GATE MARK


B414807C01
0.094,0.073 0.406,0.271 0.313,0.198 10 true *a 1.25,0.615 1.406,0.813 0.156,0.198 10 true A 2.438,1.594 2.594,1.792 0.156,0.198 10 true B
*a Reference Values


Standard:
Area Specified Condition
A 210.2 mm (8.28 in.)
B 22.6 mm (0.89 in.)



NO. 3 TAIL GATE MARK


a.

for A Deck:

B410846C01
3.531,2.219 3.531,2.427 3.531,2.427 3.833,2.427 false 0.094,0.073 0.406,0.271 0.313,0.198 10 true *a 1.406,1.625 1.594,1.833 0.188,0.208 10 true A 1.99,1.031 2.177,1.24 0.188,0.208 10 true B 5.271,1.021 5.458,1.229 0.188,0.208 10 true C 3.885,2.365 4.125,2.583 0.24,0.219 10 true *b
*a Reference Values *b Application Sheet


Standard:
Area Specified Condition Area Specified Condition
A 236.8 mm (9.32 in.) B 269.9 mm (10.6 in.)
C 269.9 mm (10.6 in.) - -



b.

for J Deck:

B410847C01
3.375,2.135 3.375,2.354 3.375,2.354 3.625,2.354 true 0.073,0.063 0.385,0.26 0.313,0.198 10 false *a 1.417,1.5 1.594,1.677 0.177,0.177 10 true A 1.927,1.063 2.104,1.24 0.177,0.177 10 true B 5.344,1.052 5.521,1.229 0.177,0.177 10 true C 3.677,2.271 3.885,2.469 0.208,0.198 10 true *b
*a Reference Values *b Application Sheet


Standard:
Area Specified Condition Area Specified Condition
A 214.3 mm (8.44 in.) B 237.5 mm (9.35 in.)
C 237.5 mm (9.35 in.) - -




FRONT DOOR NAME PLATE


B399449C03
1.583,1.75 1.583,2.135 1.583,2.135 1.865,2.135 true 1.573,4.219 1.573,4.479 1.573,4.479 1.854,4.479 true 0.073,0.344 0.344,0.552 0.271,0.208 10 true *A 0.083,2.698 0.344,2.917 0.26,0.219 10 true *B 0.76,1.979 0.927,2.156 0.167,0.177 10 true A 2.813,1.583 2.979,1.76 0.167,0.177 10 true B 0.49,4.052 0.635,4.25 0.146,0.198 10 true C 2.583,4.438 2.74,4.635 0.156,0.198 10 true D 1.927,2.042 2.188,2.26 0.26,0.219 10 true *b 1.885,4.385 2.146,4.604 0.26,0.219 10 true *b 0.063,0.042 0.323,0.26 0.26,0.219 10 true *a
*A for LH Side
*B for RH Side
*a Reference Values
*b Curve End


Standard:
Area Specified Condition
A 25.4 mm (1.0 in.)
B 13.8 mm (0.543 in.)
C 13.8 mm (0.543 in.)
D 26.7 mm (1.051 in.)