FUNCTION OF MAIN COMPONENTS
| Component | Function | |
|---|---|---|
|
*1: Models with SD20BD or SD20CD type front differential *2: Models with manual transmission *3: Models with automatic transmission *4: Models without multi-information display *5: Models with VSC *6: Models with multi-information display |
||
| Transfer Shift Actuator Assembly | Transfer Shift Motor | Switches the transfer shift position in accordance with signals from the 4 wheel drive control ECU. |
| Limit Switch (TL1, TL2, TL3) | Detects the position of the transfer shift motor and transmits a signal to the 4 wheel drive control ECU. | |
| 4WD Detection Switch | Detects the H4 position of the transfer shift position and transmits a signal to the 4 wheel drive control ECU. | |
| L4 Detection Switch | Detects the L4 position of the transfer shift position and transmits a signal to the 4 wheel drive control ECU. | |
| A.D.D. Actuator (Differential Motor Actuator Assembly)*1 | A.D.D. Shift Motor | Connects or disconnects the differential side gear inter shaft sub-assembly and differential side gear shaft sub-assembly according to signals from the 4 wheel drive control ECU. |
| Limit Switch (DL1, DL2) | Detects the position of the A.D.D. shift motor and transmits a signal to the 4 wheel drive control ECU. | |
| A.D.D. Position Switch | Detects the A.D.D. shift position (lock or free) and transmits a signal to the 4 wheel drive control ECU. | |
| Front Differential | Oil Temperature Sensor | Detects the oil temperature in the front differential. |
| Transfer Position Switch | Switches the transfer modes (H2, H4 or L4) and transmits a signal to the 4 wheel drive control ECU. | |
| Clutch Start Switch Assembly*2 | Detects the clutch pedal operation. | |
| Park/Neutral Position Switch Assembly*3 | Detects the shift lever position (P, R, N or D) and transmits a signal to the ECM. | |
| 4 Wheel Drive Control ECU | ·
Controls the transfer shift motor in the transfer shift actuator assembly in accordance with signals from each switch. ·
Controls the A.D.D. shift motor in the A.D.D. actuator (differential motor actuator assembly) in accordance with signals from each switch.*1 ·
Requests the operation of the indicator light, multi-information display and multi buzzer to the combination meter assembly according to the system status. |
|
| Skid Control ECU | ·
Transmits a vehicle speed signal to the 4 wheel drive control ECU. ·
Sends the brake control system operation status to the 4 wheel drive control ECU. |
|
| ECM | ·
Transmits a shift lever position signal to the 4 wheel drive control ECU.*3 ·
Restricts the engine output according to requests from the 4 wheel drive control ECU when the front differential oil temperature is abnormal. |
|
| Combination Meter Assembly*4 | 4WD Indicator Light / Green | Illuminates or flashes to inform the driver of the 4WD control system condition. |
| 4WD Indicator Light / Amber | ·
Flashes to inform the driver when there is a malfunction in the 4WD control system. ·
Flashes to inform the driver when the front differential oil temperature is abnormal. |
|
| 4LO Indicator Light | Illuminates or flashes to inform the driver of the 4WD control system condition. | |
| VSC OFF Indicator Light*5 | Illuminates to inform the driver when the VSC function is not operating while the transfer shift position is L4. | |
| Multi Buzzer | Sounds when the front differential oil temperature is abnormal. | |
| Combination Meter Assembly*6 | 4WD Indicator Light | Illuminates or flashes to inform the driver of the 4WD control system condition. |
| 4LO Indicator Light | Illuminates or flashes to inform the driver of the 4WD control system condition. | |
| VSC OFF Indicator Light*5 | Illuminates to inform the driver when VSC function is not operating while the transfer shift position is L4. | |
| Multi-information Display | ·
Displays to inform the driver when there is a malfunction in the 4WD control system. ·
Displays to inform the driver when the front differential oil temperature is abnormal. |
|
| Master Warning Light | Illuminates when the warning message is displayed in the multi-information display. | |
| Multi Buzzer | Sounds when the front differential oil temperature is abnormal. | |
OPERATING CONDITION
The transfer mode switching pattern of the 4WD control system is as shown in the illustration below:
Switching to each mode is possible in the following conditions.
| Switching Pattern | Transfer Mode Switching | Operation Condition |
|---|---|---|
| A | H2 → H4 | Vehicle speed is 100 km/h (62 mph) or lower. |
| B | H4 → H2 | - |
| C | H4 → L4 | ·
Vehicle is stopped or the vehicle speed is 3 km/h (2 mph) or lower. ·
Accelerator pedal is not depressed. ·
Clutch pedal is depressed. |
| D | L4 → H4 | ·
Vehicle is stopped or the vehicle speed is 3 km/h (2 mph) or lower. ·
Accelerator pedal is not depressed. ·
Clutch pedal is depressed. |
| E | L4 → H2 | ·
Vehicle is stopped or the vehicle speed is 3 km/h (2 mph) or lower. ·
Accelerator pedal is not depressed. ·
Clutch pedal is depressed. |
| Switching Pattern | Transfer Mode Switching | Operation Condition |
|---|---|---|
| A | H2 → H4 | Vehicle speed is 100 km/h (62 mph) or lower. |
| B | H4 → H2 | - |
| C | H4 → L4 | ·
Vehicle is stopped. ·
Shift lever is in N. |
| D | L4 → H4 | ·
Vehicle is stopped. ·
Shift lever is in N. |
| E | L4 → H2 | ·
Vehicle is stopped. ·
Shift lever is in N. |
DIAGNOSIS
When the 4 wheel drive control ECU detects a malfunction, the 4 wheel drive control ECU records the malfunction and memorizes the information related to the fault.
The 4 wheel drive control ECU will also store the Diagnostic Trouble Codes (DTCs) of the malfunctions. The DTCs stored in the 4 wheel drive control ECU are output to the Global TechStream (GTS) via the DLC3.
For details, refer to the Repair Manual.