Home › Engine / Hybrid System › 2TR-FBE ENGINE CONTROL › SFI SYSTEM › from 2016.07
NM33J0E _51 Engine / Hybrid System _053819 2TR-FBE ENGINE CONTROL _0261497 SFI SYSTEM CO CONTROL F

2TR-FBE ENGINE CONTROL  SFI SYSTEM  CONTROL  GLOW PLUG CONTROL  


FUNCTION


a.

The ECM estimates the ethanol concentration of the fuel in the fuel tank based on the signals it receives from the air fuel sensor. When the engine is started, the ECM activates the glow plug via the glow plug controller, based on the water temperature and ethanol concentration in the memory. As result, fuel of the optimum temperature is injected into the intake ports.



SYSTEM CONTROL


a.

The glow plug control carries out the following controls:

i.

When the ECM is activated by the courtesy switch (smart trigger system), it sends a signal to the glow plug controller. Based on this signal, the ECM decides whether the glow plug controller should heat the glow plug.


ii.

In accordance with the signals from the ECM, the glow plug controller applies current via the glow plug assembly to control the fuel temperature.


iii.

When the glow plug controller detects a malfunction in the glow circuit, it sends a diagnostic signal to the ECM.

W132602E02
5.125,2.49 5.323,2.49 5.323,2.49 5.427,1.792 true 2.01,0.583 2.688,1.792 0.677,1.208 10 false Glow Plug Controller 3.292,0.198 3.99,0.708 0.698,0.51 10 false Battery 3.031,1.125 4.229,1.865 1.198,0.74 10 false Current Application Request Signal 2.969,1.969 4.125,2.625 1.156,0.656 10 false Diagnostic Signal 4.281,2.406 5.135,2.75 0.854,0.344 10 false CAN (V Bus) 4.615,1.156 5.073,1.667 0.458,0.51 10 false ECM 5.667,0.198 7.156,0.573 1.49,0.375 10 false Courtesy Switch Signal 5.677,0.563 7.073,0.865 1.396,0.302 10 false Air Fuel Ratio Sensor 5.698,0.885 7.073,1.385 1.375,0.5 10 false Engine Coolant Temp. Sensor 5.646,1.615 6.833,2.146 1.188,0.531 10 false Combination Meter Assembly 5.646,2.229 7.01,2.604 1.365,0.375 10 false - Glow Indicator Light 0.177,2.271 1.677,2.781 1.5,0.51 10 false Glow Plug Assembly



b.

Smart Trigger System

i.

The smart trigger system is turned on by the main relay when the driver door is opened, operating the heater. As a result, it will complete heating before the driver turns the ignition switch to ON in the most case.

W132798E03
1.198,0.208 3.5,0.833 2.302,0.625 12 false with Smart Trigger System: 4.25,0.208 6.885,0.833 2.635,0.625 12 false without Smart Trigger System: 0.031,0.958 0.771,1.708 0.74,0.75 10 false Driver Side Door 0.99,0.917 1.5,1.271 0.51,0.354 10 false Open 0.948,1.302 1.458,1.656 0.51,0.354 10 false Closed 1.073,1.729 1.583,2.083 0.51,0.354 10 false On 1.073,2.083 1.583,2.438 0.51,0.354 10 false Off 1.083,2.417 1.594,2.771 0.51,0.354 10 false On 1.083,2.813 1.594,3.167 0.51,0.354 10 false Off 1.073,3.229 1.583,3.583 0.51,0.354 10 false On 1.073,3.563 1.583,3.917 0.51,0.354 10 false Off 0.833,4.01 1.781,4.313 0.948,0.302 10 false IG Switch On 1.052,4.333 1.563,4.688 0.51,0.354 10 false Off 0.021,1.75 0.906,2.219 0.885,0.469 10 false Main Relay 0.021,2.469 1.094,3.177 1.073,0.708 10 false Heating Flag at Engine Start 0.021,3.198 0.948,3.979 0.927,0.781 10 false Glow Indicator Light 0.042,4.073 0.927,4.542 0.885,0.469 10 false IG Switch 0.031,4.781 0.917,5.25 0.885,0.469 10 false Fuel Temperature 1.698,5.5 3.083,5.917 1.385,0.417 10 false Approx. 7 seconds 3.25,4.594 4.167,5.313 0.917,0.719 10 false Target Temperature 1.25,5.969 3.479,6.781 2.229,0.813 10 false The fuel is warm enough to start the engine at IG Switch on. 4.844,5.979 7.115,6.635 2.271,0.656 10 false The driver needs to wait until the fuel becomes warm at IG Switch on. 5.5,5.5 6.885,5.917 1.385,0.417 10 false Approx. 7 seconds 4.615,4.583 5.5,5.25 0.885,0.667 10 false Target Temperature 5.604,2.24 7.104,2.552 1.5,0.313 10 false Start Heating at IG On