Home › Suspension › FRONT SUSPENSION › FRONT LOWER SUSPENSION ARM(for 2WD)
RM33J0E _53 Suspension _038474 FRONT SUSPENSION _0187664 FRONT LOWER SUSPENSION ARM(for 2WD) A

FRONT SUSPENSION  FRONT LOWER SUSPENSION ARM(for 2WD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the front lower suspension arm removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced:
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Front wheel alignment adjustment
·

Clearing zero point calibration data

·

Yaw rate and acceleration sensor zero point calibration


·

DTCs are output

·

ABS warning light illumination

·

Slip indicator light illumination

·

VSC disable or malfunctioning


(Click here)


HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.REMOVE FRONT WHEEL

Hide 89543 2.DISCONNECT FRONT SPEED SENSOR LH

a.
C326177

Remove the bolt and disconnect the front speed sensor LH.


Hide 3.DISCONNECT FRONT SHOCK ABSORBER WITH COIL SPRING

C322786

a.

Remove the nut and bolt.

HINT:

While fixing the nut in place, loosen and remove the bolt.



b.

Disconnect the front shock absorber with coil spring from the front lower No. 1 suspension arm sub-assembly LH.


Hide 48810 4.DISCONNECT FRONT STABILIZER LINK ASSEMBLY LH

a.
C322828

Remove the nut and disconnect the front stabilizer link assembly LH from the front lower No. 1 suspension arm sub-assembly LH.

HINT:

If the ball joint turns together with the nut, use a 6 mm hexagon wrench to hold the stud in place.



Hide 48304 5.REMOVE FRONT NO. 1 SPRING BUMPER SUB-ASSEMBLY

a.
C322829C01
0.802,1.49 1.135,1.49 false 0.479,1.417 0.938,1.615 0.458,0.198 10 false SST 2.646,1.313 2.927,1.51 0.281,0.198 10 true *a
*a Turn


Using SST, remove the front No. 1 spring bumper sub-assembly.

SST
09922-10010  

NOTICE:

Rotate SST in the direction shown in the illustration.



Hide 48069 6.REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

C322830

a.

Remove the 2 bolts, and disconnect the front lower ball joint attachment LH from the steering knuckle.


b.
C322831C01
0.906,0.76 2.917,0.531 2.917,0.531 2.667,0.771 true 0.469,0.656 0.656,0.656 0.656,0.656 0.708,0.854 true 2.5,1.25 2.417,1.49 2.417,1.49 2.229,1.49 true 3,0.427 3.313,0.625 0.313,0.198 10 true *a 0.135,0.583 0.448,0.781 0.313,0.198 10 true *1 2.021,1.427 2.25,1.625 0.229,0.198 10 true *2
*1 No. 1 Camber Adjusting Cam
*2 No. 2 Camber Adjusting Cam
*a Matchmark


Place matchmarks on the No. 1 camber adjusting cam and vehicle frame, and No. 2 camber adjusting cam and vehicle frame.


c.

Remove the 2 nuts, No. 1 and No. 2 camber adjusting cams, 2 camber adjusting cams and front lower No. 1 suspension arm sub-assembly LH.


Hide 48626 7.REMOVE FRONT LOWER BALL JOINT ATTACHMENT LH

a.

Remove the cotter pin and nut.


b.
C322832N01
2.688,0.854 2.938,0.854 false 2.969,0.771 3.427,0.969 0.458,0.198 10 false SST

Using SST, remove the front lower ball joint attachment LH.

SST
09628-00011  


Hide 48655E 8.REMOVE FRONT LOWER NO. 2 ARM BUSH LH

a.
C322833

Using a hammer and chisel, strike and bend the entire flange of the bush as shown in the illustration.


b.
C322834N01
0.792,0.958 0.667,0.656 0.667,0.656 0.917,0.719 false 1.229,1.75 1.396,1.75 true 1.458,1.667 1.917,1.865 0.458,0.198 10 false SST 0.375,0.583 0.833,0.781 0.458,0.198 10 false SST

Using SST and a press, press out the front lower No. 2 arm bush LH.

SST
09632-36010  
09950-00020  


Hide 48654F 9.REMOVE FRONT LOWER NO. 1 ARM BUSH LH

a.
C322835N01
0.771,2.344 0.51,2.063 0.51,2.063 0.844,2.125 true 0.458,1.417 0.708,1.417 false 0.198,1.958 0.656,2.156 0.458,0.198 10 false SST 0.156,1.333 0.615,1.531 0.458,0.198 10 false SST

Using SST and a press, press out the front lower No. 1 arm bush LH.

SST
09710-14013  (09710-00021)
09950-60010  (09951-00410)
09950-70010  (09951-07360)


Hide 43340A 10.REMOVE FRONT LOWER BALL JOINT ASSEMBLY LH

a.
C237854C01
0.708,1.115 1.531,1.115 true 0.49,1 0.771,1.188 0.281,0.188 10 false *a
*a Protective tape


Using 2 screwdrivers and a hammer, remove the snap ring.

HINT:

Tape the screwdriver tip before use.



b.
C280975C01
2.302,2.208 2.094,2.208 2.094,2.208 1.906,1.427 true 0.969,0.99 1.552,0.99 false 0.49,0.052 0.802,0.25 0.313,0.198 10 false *a 3.115,0.177 3.427,0.375 0.313,0.198 10 false *b 2.354,2.146 2.813,2.344 0.458,0.198 10 false SST 0.656,0.917 1.115,1.115 0.458,0.198 10 false SST
*a Hold
*b Turn


Using SST, remove the front lower ball joint assembly LH.

SST
09950-40011  (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04031, 09957-04010, 09958-04011)
09710-22021  (09710-01081)