Home › Suspension › FRONT SUSPENSION › FRONT LOWER SUSPENSION ARM(for 4WD and Pre-Runner) › 2015.06–2015.11
RM33J0E _53 Suspension _038474 FRONT SUSPENSION _0187665 FRONT LOWER SUSPENSION ARM(for 4WD and Pre-Runner) A

FRONT SUSPENSION  FRONT LOWER SUSPENSION ARM(for 4WD and Pre-Runner)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the front lower suspension arm removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced:
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Front wheel alignment adjustment
·

Clearing zero point calibration data

·

Yaw rate and acceleration sensor zero point calibration


·

DTCs are output

·

ABS warning light illumination

·

Slip indicator light illumination

·

VSC disable or malfunctioning


(Click here)


HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.REMOVE FRONT WHEEL

Hide 51410 2.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 51442 3.REMOVE NO. 2 ENGINE UNDER COVER

Hide 4866A 4.REMOVE FRONT LOWER ARM SHAFT BOOT PROTECTOR LH (w/ Drive Shaft Boot Protector)

a.
C322842

Remove the 2 bolts and front lower arm shaft boot protector LH.


Hide 5.DISCONNECT FRONT SHOCK ABSORBER WITH COIL SPRING

C322797

a.

Remove the nut and bolt.

HINT:

While fixing the nut in place, loosen and remove the bolt.



b.

Disconnect the front shock absorber with coil spring from the front lower No. 1 suspension arm sub-assembly LH.


Hide 48069 6.REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

C322841

a.

Remove the 2 bolts, and disconnect the front lower ball joint attachment LH from the steering knuckle.


b.
C322843C01
0.917,0.74 2.792,0.542 2.792,0.542 2.615,0.781 true 0.99,1.375 1.042,1.51 1.042,1.51 1.188,1.51 true 2.49,1.344 2.542,1.479 2.542,1.479 2.688,1.479 true 2.844,0.427 3.156,0.625 0.313,0.198 10 true *a 2.729,1.406 3.042,1.604 0.313,0.198 10 true *2 1.208,1.427 1.521,1.625 0.313,0.198 10 true *1
*1 No. 1 Camber Adjusting Cam
*2 No. 2 Camber Adjusting Cam
*a Matchmark


Place matchmarks on the No. 1 camber adjusting cam and vehicle frame, and No. 2 camber adjusting cam and vehicle frame.


c.

Remove the 2 nuts, No. 1 and No. 2 camber adjusting cams, No. 1 and No. 2 camber adjusting cam assemblies and front lower No. 1 suspension arm sub-assembly LH.


Hide 48626 7.REMOVE FRONT LOWER BALL JOINT ATTACHMENT LH

a.

Remove the cotter pin and nut.


b.
C322844N01
2.594,0.792 2.844,0.792 false 2.906,0.729 3.365,0.927 0.458,0.198 10 false SST

Using SST, remove the front lower ball joint attachment LH.

SST
09628-00011  


Hide 48654F 8.REMOVE FRONT NO. 1 LOWER ARM BUSH

a.
C322845

Using a hammer and chisel, strike and bend the entire flange of the bush as shown in the illustration.


b.
C322846N01
0.646,0.938 0.479,0.646 0.479,0.646 0.771,0.688 false 1.063,1.563 1.229,1.563 false 0.188,0.573 0.646,0.771 0.458,0.198 10 false SST 1.281,1.49 1.74,1.688 0.458,0.198 10 false SST

Using SST and a press, press out the front No. 1 lower arm bush.

SST
09632-36010  
09513-36040  
09950-00020  


Hide 48655E 9.REMOVE FRONT NO. 2 LOWER ARM BUSH

a.
C322845

Using a hammer and chisel, strike and bend the entire flange of the bush as shown in the illustration.


b.
C322847N01
0.625,0.938 0.417,0.656 0.417,0.656 0.771,0.688 false 1.052,1.552 1.302,1.552 false 0.125,0.583 0.583,0.781 0.458,0.198 10 false SST 1.354,1.479 1.813,1.677 0.458,0.198 10 false SST

Using SST and a press, press out the front No. 2 lower arm bush.

SST
09632-36010  
09513-36040  
09950-00020  


Hide 43340A 10.REMOVE FRONT LOWER BALL JOINT ASSEMBLY LH

a.
C237854C01
0.708,1.115 1.531,1.115 true 0.49,1 0.771,1.188 0.281,0.188 10 false *a
*a Protective tape


Using 2 screwdrivers and a hammer, remove the snap ring.

HINT:

Tape the screwdriver tip before use.



b.
C280975C01
2.302,2.208 2.094,2.208 2.094,2.208 1.906,1.427 true 0.969,0.99 1.552,0.99 false 0.49,0.052 0.802,0.25 0.313,0.198 10 false *a 3.115,0.177 3.427,0.375 0.313,0.198 10 false *b 2.354,2.146 2.813,2.344 0.458,0.198 10 false SST 0.656,0.917 1.115,1.115 0.458,0.198 10 false SST
*a Hold
*b Turn


Using SST, remove the front lower ball joint assembly LH.

SST
09950-40011  (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04031, 09957-04010, 09958-04011)
09710-22021  (09710-01081)


Hide 48304 11.REMOVE FRONT NO. 1 SPRING BUMPER SUB-ASSEMBLY

a.
C322876N01
2.5,1.438 2.26,1.438 2.26,1.438 2.188,1.24 false 2.563,1.365 3.021,1.563 0.458,0.198 10 false SST

Using SST, remove the front No. 1 spring bumper sub-assembly from the vehicle.

SST
09922-10010