| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B1500 | Fuel Sender Open Detected | Both conditions are met:
·
The voltage at the IG power supply terminal of the combination meter assembly is between 9.5 and 11.5 V. ·
Average input signal of fuel sender gauge is 4.85 V or more or 0.15 V or less. |
·
Fuel sender gauge assembly ·
Fuel suction with pump and gauge tube assembly*1 ·
Fuel tank vent tube assembly*2 ·
Harness or connector ·
Combination meter assembly |
*1: for 2TR-FE
*2: except 2TR-FE
Be careful of flames.
When replacing the combination meter assembly, make sure to replace it with a new one.
Using the GTS, read the Data List.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Fuel Input | Fuel input | Min.: 0, Max.: 127.5 | Current fuel level displayed | Unit: Liter |
| Tester Display |
|---|
| Fuel Input |
Fuel amount value displayed on the GTS is almost the same as the needle indication.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G9 combination meter assembly connector.
Disconnect the O6 fuel suction tube with pump and gauge assembly*1 or fuel tank vent tube assembly*2 connector.
*1: for 2TR-FE
*2: except 2TR-FE
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G9-25 (FR) - O6-3 (FR) | Always | Below 1 Ω |
| G9-24 (FV) - O6-1 (FV) | Always | Below 1 Ω |
| G9-26 (FE&B) - O6-2 (FE) | Always | Below 1 Ω |
| G9-25 (FR) or O6-3 (FR) - Body ground | Always | 10 kΩ or higher |
| G9-24 (FV) or O6-1 (FV) - Body ground | Always | 10 kΩ or higher |
| G9-26 (FE&B) or O6-2 (FE) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Combination Meter Assembly) |
Remove the combination meter assembly with its connectors still connected.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G9-24 (FV) - Body ground | Always | 4.5 to 5.2 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G9-26 (FE&B) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Combination Meter Assembly) |
Remove the combination meter assembly with its connectors still connected.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G9-25 (FR) - Body ground | Fuel quantity 73.5 liters (77.7 US qts, 64.7 Imp. qts) or more | 4.20 to 4.32 V |
| Fuel quantity 40 liters (42.3 US qts, 35.2 Imp. qts) | 2.21 to 2.51 V | |
| Fuel quantity 5.8 liters (6.1 US qts, 5.1 Imp. qts) or less | 0.63 to 0.75 V |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for 2TR-FE) | B |
| NG (except 2TR-FE) | C |
A
B
C
| *a | Upper Side |
| *b | Lower Side
(to Fuel Sender Gauge Assembly) |
| *c | Connector A |
| *d | Connector B |
Remove the fuel suction with pump and gauge tube assembly.
Click hereEngine / Hybrid System>2TR-FE FUEL>FUEL SENDER GAUGE ASSEMBLY>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-2 - B-2 | Always | Below 1 Ω |
| A-3 - B-1 | Always | Below 1 Ω |
| A-1 - B-3 | Always | Below 1 Ω |
| A-2 - B-1 | Always | 10 kΩ or higher |
| A-2 - B-3 | Always | 10 kΩ or higher |
| A-3 - B-3 | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Upper Side |
| *b | Lower Side
(to Fuel Sender Gauge Assembly) |
| *c | Connector A |
| *d | Connector B |
Remove the fuel tank vent tube assembly.
for 1GD-FTV: Click hereEngine / Hybrid System>1GD-FTV FUEL>FUEL SENDER GAUGE ASSEMBLY>REMOVAL
for 2GD-FTV: Click hereEngine / Hybrid System>2GD-FTV FUEL>FUEL SENDER GAUGE ASSEMBLY>REMOVAL
for 1KD-FTV: Click hereEngine / Hybrid System>1KD-FTV FUEL>FUEL SENDER GAUGE ASSEMBLY>REMOVAL
for 2KD-FTV: Click hereEngine / Hybrid System>2KD-FTV FUEL>FUEL SENDER GAUGE ASSEMBLY>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-2 - B-2 | Always | Below 1 Ω |
| A-3 - B-1 | Always | Below 1 Ω |
| A-1 - B-3 | Always | Below 1 Ω |
| A-2 - B-1 | Always | 10 kΩ or higher |
| A-2 - B-3 | Always | 10 kΩ or higher |
| A-3 - B-3 | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for 1GD-FTV: Click hereEngine / Hybrid System>1GD-FTV FUEL>FUEL SENDER GAUGE ASSEMBLY>REMOVAL
for 2GD-FTV: Click hereEngine / Hybrid System>2GD-FTV FUEL>FUEL SENDER GAUGE ASSEMBLY>REMOVAL
for 1KD-FTV: Click hereEngine / Hybrid System>1KD-FTV FUEL>FUEL SENDER GAUGE ASSEMBLY>REMOVAL
for 2KD-FTV: Click hereEngine / Hybrid System>2KD-FTV FUEL>FUEL SENDER GAUGE ASSEMBLY>REMOVAL
NG
for 1GD-FTV: Click hereEngine / Hybrid System>1GD-FTV FUEL>FUEL SENDER GAUGE ASSEMBLY>REMOVAL
for 2GD-FTV: Click hereEngine / Hybrid System>2GD-FTV FUEL>FUEL SENDER GAUGE ASSEMBLY>REMOVAL
for 1KD-FTV: Click hereEngine / Hybrid System>1KD-FTV FUEL>FUEL SENDER GAUGE ASSEMBLY>REMOVAL
for 2KD-FTV: Click hereEngine / Hybrid System>2KD-FTV FUEL>FUEL SENDER GAUGE ASSEMBLY>REMOVAL