Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM33J0E _58 Vehicle Interior _038499 METER / GAUGE / DISPLAY _0189806 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B1507  Open in Turn Signal Circuit  B1508  Short in Turn Signal / Hazard Flasher Circuit  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area
B1507 Open in Turn Signal Circuit Open in turn signal light circuit.
·

Harness or connector

·

Side turn signal light assembly*1

·

Outer rear view mirror assembly*1

·

Rear combination light socket and wire sub-assembly*2

·

Combination meter assembly


B1508 Short in Turn Signal / Hazard Flasher Circuit Short in turn signal light circuit or hazard warning light circuit.
·

Harness or connector

·

Side turn signal light assembly*1

·

Outer rear view mirror assembly*1

·

Rear combination light socket and wire sub-assembly*2

·

Combination meter assembly



*1: w/ Outer Rear View Mirror Type Side Turn Signal Light

*2: w/ Deck


WIRING DIAGRAM

E326582E01
0.74,1.604 3.323,1.875 2.583,0.271 10 false Side Turn Signal Light Assembly LH 0.188,0.271 4.385,0.729 4.198,0.458 12 false w/ Outer Rear View Mirror Type Side Turn Signal Light: 2.188,3.531 4.771,3.802 2.583,0.271 10 false A32 0.188,2.438 4.385,2.896 4.198,0.458 12 false w/ Front Fender Type Side Turn Signal Light: 3.385,1.583 4.875,1.958 1.49,0.375 10 false Outer Rear View Mirror Assembly LH 4.698,1.26 5.271,1.635 0.573,0.375 10 false K3 4.719,0.854 5.292,1.229 0.573,0.375 10 false K3 4.719,0.646 5.292,1.021 0.573,0.375 10 false 10 6.25,0.792 6.823,1.167 0.573,0.375 10 false LL 6.052,0.75 6.625,1.125 0.573,0.375 10 false 8 4.24,0.76 4.813,1.135 0.573,0.375 10 false TRNL 3.292,0.844 3.865,1.219 0.573,0.375 10 false A 3.302,1.24 3.875,1.615 0.573,0.375 10 false A 3.323,1.073 3.896,1.448 0.573,0.375 10 false 2 3.323,0.656 3.896,1.031 0.573,0.375 10 false 1 4.677,3.094 5.25,3.469 0.573,0.375 10 false 2 4.688,2.844 5.26,3.219 0.573,0.375 10 false 1 4.75,1.063 5.323,1.438 0.573,0.375 10 false 6 4.281,1.167 4.854,1.542 0.573,0.375 10 false GND 2.323,4.958 4.906,5.229 2.583,0.271 10 false A30 2.333,5.135 4.917,5.406 2.583,0.271 10 false Headlight Assembly LH 4.677,4.25 5.25,4.625 0.573,0.375 10 false 2 4.677,4.51 5.25,4.885 0.573,0.375 10 false 1 4.469,4.51 5.042,4.885 0.573,0.375 10 false E 4.458,4.271 5.031,4.646 0.573,0.375 10 false B 2.208,6.375 4.792,6.646 2.583,0.271 10 false O2 2.24,6.531 4.823,6.802 2.583,0.271 10 false Rear Combination Light Assembly LH 4.479,5.688 5.052,6.063 0.573,0.375 10 false B 4.479,5.938 5.052,6.313 0.573,0.375 10 false E 4.698,5.677 5.271,6.052 0.573,0.375 10 false 1 4.688,5.917 5.26,6.292 0.573,0.375 10 false 3 5.927,7.698 6.896,8.115 0.969,0.417 10 false G11 5.938,7.854 7.125,8.219 1.188,0.365 10 false Combination Meter Assembly 2.188,3.688 4.771,3.958 2.583,0.271 10 false Side Turn Signal Light Assembly LH 4.469,7.271 5.042,7.646 0.573,0.375 10 false B 4.708,7.271 5.281,7.646 0.573,0.375 10 false 1 4.708,7.521 5.281,7.896 0.573,0.375 10 false 3 4.458,7.531 5.031,7.906 0.573,0.375 10 false E 3.26,7.281 3.833,7.656 0.573,0.375 10 false 1 3.271,7.542 3.844,7.917 0.573,0.375 10 false 2 1.635,7.99 3.104,8.354 1.469,0.365 10 false Rear Combination Light Assembly LH 3.229,7.958 5.813,8.229 2.583,0.271 10 false O2 3.24,8.125 5.177,8.49 1.938,0.365 10 false Rear Combination Light Socket and Wire Sub-assembly LH 0.219,5.542 2.802,5.813 2.583,0.271 12 false w/o Deck: 0.219,7.115 2.802,7.385 2.583,0.271 12 false w/ Deck:

E326583E01
6.229,0.823 6.542,1.021 0.313,0.198 10 false LR 5.969,0.75 6.281,0.948 0.313,0.198 10 false 13 0.167,0.24 4.313,0.667 4.146,0.427 12 false w/ Outer Rear View Mirror Type Side Turn Signal Light: 0.208,2.438 4.354,2.865 4.146,0.427 12 false w/ Front Fender Type Side Turn Signal Light: 0.74,1.573 4.885,2 4.146,0.427 10 false Side Turn Signal Light Assembly RH 3.281,1.25 3.781,1.51 0.5,0.26 10 false A 3.271,0.844 3.771,1.104 0.5,0.26 10 false A 3.323,0.646 3.823,0.906 0.5,0.26 10 false 1 3.333,1.073 3.833,1.333 0.5,0.26 10 false 2 4.76,1.083 5.26,1.344 0.5,0.26 10 false 6 4.719,0.667 5.219,0.927 0.5,0.26 10 false 10 4.688,0.844 5,1.042 0.313,0.198 10 false J3 4.708,1.26 5.021,1.458 0.313,0.198 10 false J3 4.198,0.781 4.688,0.979 0.49,0.198 10 false TRNR 4.26,1.146 4.75,1.344 0.49,0.198 10 false GND 3.49,1.583 4.896,1.938 1.406,0.354 10 false Outer Rear View Mirror Assembly RH 2.26,3.542 6.406,3.969 4.146,0.427 10 false A31 2.271,3.688 6.417,4.115 4.146,0.427 10 false Side Turn Signal Light Assembly RH 4.698,2.854 5.198,3.115 0.5,0.26 10 false 1 4.698,3.115 5.198,3.375 0.5,0.26 10 false 2 4.688,4.281 5.188,4.542 0.5,0.26 10 false 2 4.688,4.5 5.188,4.76 0.5,0.26 10 false 1 4.688,5.906 5.188,6.167 0.5,0.26 10 false 3 4.469,4.271 4.969,4.531 0.5,0.26 10 false B 4.479,5.688 4.979,5.948 0.5,0.26 10 false B 4.479,4.521 4.979,4.781 0.5,0.26 10 false E 2.375,4.948 4.292,5.208 1.917,0.26 10 false A29 2.365,5.094 4.281,5.354 1.917,0.26 10 false Headlight Assembly RH 4.677,5.667 5.177,5.927 0.5,0.26 10 false 1 2.198,6.344 4.115,6.604 1.917,0.26 10 false O1 2.208,6.49 4.854,6.813 2.646,0.323 10 false Rear Combination Light Assembly RH 5.885,7.823 7.083,8.198 1.198,0.375 10 false G11 5.885,7.979 7.083,8.354 1.198,0.375 10 false Combination Meter Assembly 4.448,7.24 4.948,7.5 0.5,0.26 10 false B 4.479,5.927 4.979,6.188 0.5,0.26 10 false E 4.469,7.469 4.969,7.729 0.5,0.26 10 false E 1.719,7.938 3.25,8.354 1.531,0.417 10 false Rear Combination Light Assembly RH 4.688,7.219 5.188,7.479 0.5,0.26 10 false 1 4.698,7.469 5.198,7.729 0.5,0.26 10 false 3 0.26,7.104 1.792,7.521 1.531,0.417 12 false w/ Deck: 0.219,5.5 1.75,5.917 1.531,0.417 12 false w/o Deck: 3.219,7.938 5.375,8.375 2.156,0.438 10 false O1 3.219,8.083 5.375,8.521 2.156,0.438 10 false Rear Combination Light Socket and Wire Sub-assembly RH

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the combination meter assembly, make sure to replace it with a new one.

·

Inspect the bulbs for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR

Body Electrical > Combination Meter > Clear DTCs
50002 122

b.

Recheck for DTCs and check that no DTCs are output.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR

Body Electrical > Combination Meter > Trouble Codes
50001 122
OK:

B1507 and B1508 are not output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK TURN SIGNAL LIGHT
2.CHECK TURN SIGNAL LIGHT
a.

Check the illumination of each turn signal light.


Result:
Result Proceed to
LH side turn signal light does not illuminate. A
RH side turn signal light does not illuminate. B



A

3.CHECK HARNESS AND CONNECTOR (LH SIDE CIRCUIT)

B

8.CHECK HARNESS AND CONNECTOR (RH SIDE CIRCUIT)
3.CHECK HARNESS AND CONNECTOR (LH SIDE CIRCUIT)

*1: w/ Outer Rear View Mirror Type Side Turn Signal Light

*2: w/ Front Fender Type Side Turn Signal Light

*3: w/o Deck

*4: w/ Deck


a.

Disconnect the G11 combination meter assembly connector.


b.

Disconnect the A30 headlight assembly LH connector.


c.

Disconnect the K3 outer rear view mirror assembly LH connector.*1


d.

Disconnect the A32 side turn signal light assembly LH connector.*2


e.

Disconnect the O2 rear combination light assembly LH*3 or rear combination light socket and wire sub-assembly LH*4 connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G11-8 (LL) - A30-2 (B) Always Below 1 Ω
G11-8 (LL) - K3-10 (TRNL)*1 Always Below 1 Ω
G11-8 (LL) - A32-1*2 Always Below 1 Ω
G11-8 (LL) - O2-1 (B) Always Below 1 Ω
A30-1 (E) - Body ground Always Below 1 Ω
K3-6 (GND) - Body ground*1 Always Below 1 Ω
A32-2 - Body ground*2 Always Below 1 Ω
O2-3 (E) - Body ground Always Below 1 Ω
G11-8 (LL) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (w/ Outer Rear View Mirror Type Side Turn Signal Light) A
OK (w/ Front Fender Type Side Turn Signal Light) B
NG C



A

4.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH

B

5.CHECK REAR COMBINATION LIGHT TYPE

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH
a.

Remove the outer rear view mirror assembly LH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL


b.

Inspect the outer rear view mirror assembly LH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK REAR COMBINATION LIGHT TYPE

NG

7.INSPECT SIDE TURN SIGNAL LIGHT ASSEMBLY LH
5.CHECK REAR COMBINATION LIGHT TYPE
a.

Check the rear combination light type.


Result:
Result Proceed to
w/ Deck A
w/o Deck B



A

6.INSPECT REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY LH

B

REPLACE COMBINATION METER ASSEMBLY

6.INSPECT REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY LH
a.
E326586E01
1.479,2.5 1.958,2.708 0.479,0.208 1.479,0.25 1.958,0.458 0.479,0.208 1.74,3.427 2.24,2.854 2.24,2.854 2.427,2.854 true 2.063,3.521 2.573,3.833 2.573,3.833 2.76,3.833 true 2.135,1.083 2.427,0.781 2.427,0.781 2.615,0.781 true 0.719,0.885 0.896,0.885 0.896,0.885 1.198,1.135 true 2.49,2.74 2.896,3.021 0.406,0.281 10 false 1 2.813,3.719 3.219,4 0.406,0.281 10 false 2 2.677,0.656 3.083,0.938 0.406,0.281 10 false B 0.573,0.771 0.979,1.052 0.406,0.281 10 false E 1.667,0.271 2.073,0.552 0.406,0.281 10 false A 1.667,2.51 2.073,2.792 0.406,0.281 10 false B

Remove the rear combination light socket and wire sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY>DISASSEMBLY


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-1 (B) - B-1 Always Below 1 Ω
A-3 (E) - B-2 Always Below 1 Ω
A-1 (B) or B-1 - Body ground Always 10 kΩ or higher
A-3 (E) or B-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY LH

7.INSPECT SIDE TURN SIGNAL LIGHT ASSEMBLY LH


Result:
Proceed to
OK
NG



OK

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH

NG

8.CHECK HARNESS AND CONNECTOR (RH SIDE CIRCUIT)

*1: w/ Outer Rear View Mirror Type Side Turn Signal Light

*2: w/ Front Fender Type Side Turn Signal Light

*3: w/o Deck

*4: w/ Deck


a.

Disconnect the G11 combination meter assembly connector.


b.

Disconnect the A29 headlight assembly RH connector.


c.

Disconnect the J3 outer rear view mirror assembly RH connector.*1


d.

Disconnect the A31 side turn signal light assembly RH connector.*2


e.

Disconnect the O1 rear combination light assembly RH*3 or rear combination light socket and wire sub-assembly RH*4 connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G11-13 (LR) - A29-2 (B) Always Below 1 Ω
G11-13 (LR) - J3-10 (TRNR)*1 Always Below 1 Ω
G11-13 (LR) - A31-1*2 Always Below 1 Ω
G11-13 (LR) - O1-1 (B) Always Below 1 Ω
A29-1 (E) - Body ground Always Below 1 Ω
J3-6 (GND) - Body ground*1 Always Below 1 Ω
A31-2 - Body ground*2 Always Below 1 Ω
O1-3 (E) - Body ground Always Below 1 Ω
G11-13 (LR) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (w/ Outer Rear View Mirror Type Side Turn Signal Light) A
OK (w/ Front Fender Type Side Turn Signal Light) B
NG C



A

9.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH

B

10.CHECK REAR COMBINATION LIGHT TYPE

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH
a.

Remove the outer rear view mirror assembly RH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL


b.

Inspect the outer rear view mirror assembly RH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>INSPECTION


Result:
Proceed to
OK
NG



OK

10.CHECK REAR COMBINATION LIGHT TYPE

NG

12.INSPECT SIDE TURN SIGNAL LIGHT ASSEMBLY RH
10.CHECK REAR COMBINATION LIGHT TYPE
a.

Check the rear combination light type.


Result:
Result Proceed to
w/ Deck A
w/o Deck B



A

11.INSPECT REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY RH

B

REPLACE COMBINATION METER ASSEMBLY

11.INSPECT REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY RH
a.
E326586E01
1.479,2.5 1.958,2.708 0.479,0.208 1.479,0.25 1.958,0.458 0.479,0.208 1.74,3.427 2.24,2.854 2.24,2.854 2.427,2.854 true 2.063,3.521 2.573,3.833 2.573,3.833 2.76,3.833 true 2.135,1.083 2.427,0.781 2.427,0.781 2.615,0.781 true 0.719,0.885 0.896,0.885 0.896,0.885 1.198,1.135 true 2.49,2.74 2.896,3.021 0.406,0.281 10 false 1 2.813,3.719 3.219,4 0.406,0.281 10 false 2 2.677,0.656 3.083,0.938 0.406,0.281 10 false B 0.573,0.771 0.979,1.052 0.406,0.281 10 false E 1.667,0.271 2.073,0.552 0.406,0.281 10 false A 1.667,2.51 2.073,2.792 0.406,0.281 10 false B

Remove the rear combination light socket and wire sub-assembly RH.

Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY>DISASSEMBLY


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-1 (B) - B-1 Always Below 1 Ω
A-3 (E) - B-2 Always Below 1 Ω
A-1 (B) or B-1 - Body ground Always 10 kΩ or higher
A-3 (E) or B-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY RH

12.INSPECT SIDE TURN SIGNAL LIGHT ASSEMBLY RH


Result:
Proceed to
OK
NG



OK

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH

NG