Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2015.06–2015.11
RM33J0E _58 Vehicle Interior _038499 METER / GAUGE / DISPLAY _0189806 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B150A  Lost Communication with HMI-LAN  


DESCRIPTION

The combination meter assembly receives a text data signal from the radio and display receiver assembly via local bus communication.

Based on this signal, audio system information is displayed on the multi-information display.

This DTC is stored when the combination meter assembly cannot receive the signal.

DTC No. Detection Item DTC Detection Condition Trouble Area
B150A Lost Communication with HMI-LAN After the combination meter assembly receives a registration information signal, which is sent by the radio and display receiver assembly when the ignition switch is ACC, 1 or more times, the combination meter assembly cannot receive the signal for 30 seconds or more.
·

Harness or connector

·

Radio and display receiver assembly

·

Combination meter assembly



WIRING DIAGRAM

E295995E18
5.177,2.698 7.156,2.927 1.979,0.229 10 false G9 5.188,2.854 7.021,3.25 1.833,0.396 10 false Combination Meter Assembly 5.375,1.802 6.5,2.104 1.125,0.302 10 false LCL- 5.375,1.125 6.5,1.427 1.125,0.302 10 false LCL+ 5.094,1.688 6.313,1.99 1.219,0.302 10 false 37 5.073,1.021 6.292,1.323 1.219,0.302 10 false 38 1.125,3.396 2.885,3.708 1.76,0.313 10 false : CAN Communication Line 0.375,2.698 2.094,3.01 1.719,0.313 10 false G38 0.375,2.875 2.792,3.292 2.417,0.417 10 false Radio and Display Receiver Assembly 1.427,1.135 1.979,1.521 0.552,0.385 10 false CNH1 1.938,1 3.063,1.302 1.125,0.302 10 false 3 1.948,1.656 3.073,1.958 1.125,0.302 10 false 4 1.427,1.844 1.979,2.229 0.552,0.385 10 false CNL1

CAUTION / NOTICE / HINT

NOTICE:

When replacing the combination meter assembly, make sure to replace it with a new one.


PROCEDURE

1.CHECK FOR DTC (AUDIO AND VISUAL SYSTEM)
a.

Check for DTCs.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)

NG

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the G9 combination meter assembly connector.


b.

Disconnect the G38 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G9-38 (LCL+) - G38-3 (CNH1) Always Below 1 Ω
G9-37 (LCL-) - G38-4 (CNL1) Always Below 1 Ω
G9-38 (LCL+) or G38-3 (CNH1) - Body ground Always 10 kΩ or higher
G9-37 (LCL-) or G38-4 (CNL1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK COMBINATION METER ASSEMBLY
a.

Replace the combination meter assembly with a new one.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


b.

Turn the ignition switch ON and wait 30 seconds.

NOTICE:

A maximum of 30 seconds is required to send/receive the registration information between the combination meter assembly and navigation receiver assembly.



c.
E274321C03
1.865,0.708 1.865,0.396 false 1.771,0.229 2.083,0.427 0.313,0.198 10 false *b 0.313,0.229 0.625,0.427 0.313,0.198 10 false *a
*a Multi-information Display
*b Audio Tab


Operate the steering pad switch assembly and check that the audio tab illuminates.


d.

Check for DTCs.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR

Body Electrical > Combination Meter > Trouble Codes
50001 122
OK:

The audio tab illuminates and DTC B150A is not output.



Result:
Proceed to
OK
NG



OK

END (COMBINATION METER ASSEMBLY IS DEFECTIVE)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY