Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM
RM33J0E _58 Vehicle Interior _040893 SEAT BELT _0189858 SEAT BELT WARNING SYSTEM D

SEAT BELT  SEAT BELT WARNING SYSTEM  OPERATION CHECK  


INSPECT DRIVER SEAT BELT WARNING SYSTEM


HINT:

The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat.


a.

Turn the ignition switch to ON.


b.

When the driver seat belt is not fastened, check that the seat belt warning light on the combination meter assembly blinks.


c.

Lift up the vehicle using a swing arm type lift.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS


d.

Start the engine.


e.

When the driver seat belt is not fastened and the vehicle is driven at approximately 20 km/h (12 mph) or more, check that the seat belt warning light on the combination meter assembly blinks at an interval of 1.2 second for 30 seconds.

After that, check that the seat belt warning light on the combination meter assembly blinks at an interval of 0.4 seconds.


f.

When the driver seat belt is fastened, check that the seat belt warning light on the combination meter assembly turns off.



INSPECT FRONT PASSENGER SEAT BELT WARNING SYSTEM


HINT:

The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat.


a.

Turn the ignition switch to ON.


b.

Place a weight of 20 kg (44.0 lb) on the front passenger seat.

NOTICE:

Place the weight on the seat cushion and do not allow it to come into contact with the seatback.



c.

Fasten the driver seat belt.


d.

When the front passenger seat belt is not fastened, check that the seat belt warning light on the combination meter assembly blinks.


e.

Lift up the vehicle using a swing arm type lift.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS


f.

Start the engine.


g.

When the front passenger seat is occupied, the front passenger seat belt is not fastened and the vehicle is driven at approximately 20 km/h (12 mph) or more, check that the seat belt warning light on the combination meter assembly blinks at an interval of 1.2 second for 30 seconds.

After that, check that the seat belt warning light on the combination meter assembly blinks at an interval of 0.4 seconds.


h.

When the front passenger seat belt is fastened, check that the seat belt warning light on the combination meter assembly turns off.



INSPECT REAR SEAT BELT WARNING SYSTEM (w/ Rear Seat Belt Warning)


B379201C02
0.625,1.74 0.875,1.74 0.875,1.74 1.125,1.24 true 2.792,1.76 2.542,1.76 2.542,1.76 2.271,1.24 true 1.708,1.76 1.708,1.26 true 0.063,0.073 0.375,0.271 0.313,0.198 10 false *1 0.458,1.646 0.771,1.844 0.313,0.198 10 false *a 1.635,1.781 1.948,1.979 0.313,0.198 10 false *b 2.833,1.656 3.146,1.854 0.313,0.198 10 false *c
*1 Rear Seat Belt Warning Light (Telltale Light Assembly)
*a LH
*b Center
*c RH


a.

Check the state of the rear seat belt warning light on the telltale light assembly under the following conditions:

i.

Turn the ignition switch to off.


ii.

Turn the ignition switch to ON.


iii.

Open and then close either rear door.


iv.

When a rear seat belt is not fastened, check that the rear seat belt warning light on the telltale light assembly is illuminated.


v.

After 34 seconds, check that the rear seat belt warning light on the telltale light assembly turns off.


vi.

When one of the rear seat belts is unfastened from being fastened, check that the rear seat belt warning light on the telltale light assembly illuminates.




INSPECT SEAT BELT WARNING BUZZER


HINT:

The seat belt warning buzzer can be customized. Make sure that this function is ON.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>CUSTOMIZE PARAMETERS


*: w/ Rear Seat Belt Warning


a.

Place a weight of 20 kg (44.0 lb) on the front passenger seat.

NOTICE:

Place the weight on the seat cushion and do not allow it to come into contact with the seatback.



b.

Lift up the vehicle using a swing arm type lift.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS


c.

Start the engine.


d.

Check that the seat belt warning buzzer in the combination meter assembly sounds at an interval of 1.2 second for 30 seconds.


e.

After the seat belt warning buzzer has been sounding for 30 seconds at an interval of 1.2 second, check that the seat belt warning buzzer in the combination meter assembly sounds at an interval of 0.4 seconds for 90 seconds.


f.

Check that the seat belt warning buzzer in the combination meter assembly stops 2 minutes after it started sounding at an interval of 1.2 second.


g.

After the buzzer has stopped, turn the ignition switch off and then start the engine again. Drive the vehicle at approximately 20 km/h (12 mph) or more while the driver, front passenger or a rear* seat belt is not fastened, and check that the buzzer sounds again.


h.

After the buzzer has stopped, fasten the driver and front passenger seat belts. Drive the vehicle at approximately 20 km/h (12 mph) or more and unfasten the driver, front passenger or a rear* seat belt, and check that the buzzer sounds again.


i.

After the buzzer has stopped, stop the vehicle, move the shift lever to R, and then move it to any other position except R. Drive the vehicle at approximately 20 km/h (12 mph) or more, and check that the buzzer sounds again.