Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or any doors. If doors need to be opened in order to check connectors, open the doors and leave them open.
After turning the cable disconnected from negative (-) battery terminal, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
JUNCTION CONNECTOR
No. 1 CAN Junction Connector
| *a | Front view of wire harness connector
(to No. 1 CAN Junction Connector) |
*b | for Brake Actuator Assembly (Skid Control ECU) |
| *c | for Airbag Sensor Assembly | *d | for Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor) (w/ VSC) |
| *e | for DLC3 | *f | for Combination Meter Assembly |
| *g | for No. 2 CAN Junction Connector | - | - |
| No. 1 CAN Junction Connector | Wiring Color | Connect to |
|---|---|---|
|
*: w/ VSC |
||
| G67-1 (CANH) | B | Brake actuator assembly (skid control ECU) |
| G67-11 (CANL) | W | |
| G67-2 (CANH) | Y | Airbag sensor assembly |
| G67-12 (CANL) | W | |
| G67-3 (CANH) | BE | Spiral with sensor cable sub-assembly (steering angle sensor)* |
| G67-13 (CANL) | W | |
| G67-4 (CANH) | L | DLC3 |
| G67-14 (CANL) | W | |
| G67-5 (CANH) | SB | Combination meter assembly |
| G67-15 (CANL) | W | |
| G67-6 (CANH) | LG | No. 2 CAN junction connector |
| G67-16 (CANL) | W | |
No. 2 CAN Junction Connector
| *a | Front view of wire harness connector
(to No. 2 CAN Junction Connector) |
*b | for Certification ECU (Smart Key ECU Assembly) (w/ Smart Entry and Start System) |
| *c | for 4 Wheel Drive Control ECU (for 4WD) | *d | for ECM |
| *e | for No. 1 CAN Junction Connector | *f | for Radio and Display Receiver Assembly (w/ Audio and Visual System [for Radio and Display Type]) |
| *g | for Air Conditioning Amplifier Assembly (for Automatic Air Conditioning System) | - | - |
| No. 2 CAN Junction Connector | Wiring Color | Connect to |
|---|---|---|
|
*1: w/ Smart Entry and Start System *2: for 4WD *3: w/ Audio and Visual System (for Radio and Display Type) *4: for Automatic Air Conditioning System |
||
| G68-3 (CANH) | G | Certification ECU (smart key ECU assembly)*1 |
| G68-13 (CANL) | W | |
| G68-4 (CANH) | R | 4 wheel drive control ECU*2 |
| G68-14 (CANL) | W | |
| G68-5 (CANH) | B | ECM |
| G68-15 (CANL) | W | |
| G68-6 (CANH) | LG | No. 1 CAN junction connector |
| G68-16 (CANL) | W | |
| G68-7 (CANH) | V | Radio and display receiver assembly*3 |
| G68-17 (CANL) | W | |
| G68-10 (CANH) | GR | Air conditioning amplifier assembly*4 |
| G68-20 (CANL) | W | |
CHECK DLC3
| *a | Front view of DLC3 |
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
After turning the cable disconnected from negative (-) battery terminal, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click here
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click here
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G8-6 (CANH) - G8-14 (CANL) | L - W | HIGH-level CAN bus wire - LOW-level CAN bus wire | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| G8-6 (CANH) - G8-4 (CG) | L - W-B | HIGH-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G8-14 (CANL) - G8-4 (CG) | W - W-B | LOW-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G8-6 (CANH) - G8-16 (BAT) | L - G | HIGH-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G8-14 (CANL) - G8-16 (BAT) | W - G | LOW-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CHECK ECM (for 2TR-FE)
Disconnect the ECM connectors.
| *a | Front view of wire harness connector
(to ECM) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G45-13 (CANH) - G45-14 (CANL) | B - W | HIGH-level CAN bus wire - LOW-level CAN bus wire | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| G45-13 (CANH) - C52-3 (E1) | B - W-B | HIGH-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G45-14 (CANL) - C52-3 (E1) | W - W-B | LOW-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G45-13 (CANH) - G46-3 (BATT) | B - Y | HIGH-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G45-14 (CANL) - G46-3 (BATT) | W - Y | LOW-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CHECK ECM (for 1GD-FTV, 2GD-FTV)
Disconnect the ECM connectors.
| *a | Front view of wire harness connector
(to ECM) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G85-17 (CANH) - G85-28 (CANL) | B - W | HIGH-level CAN bus wire - LOW-level CAN bus wire | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| G85-17 (CANH) - C60-1 (E1) | B - W-B | HIGH-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G85-28 (CANL) - C60-1 (E1) | W - W-B | LOW-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G85-17 (CANH) - G86-1 (BATT) | B - Y | HIGH-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G85-28 (CANL) - G86-1 (BATT) | W - Y | LOW-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CHECK ECM (for 1KD-FTV, 2KD-FTV)
Disconnect the ECM connectors.
| *a | Front view of wire harness connector
(to ECM) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G83-24 (CANH) - G83-23 (CANL) | B - W | HIGH-level CAN bus wire - LOW-level CAN bus wire | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| G83-24 (CANH) - C56-7 (E1) | B - W-B | HIGH-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G83-23 (CANL) - C56-7 (E1) | W - W-B | LOW-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G83-24 (CANH) - G83-2 (BATT) | B - Y | HIGH-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G83-23 (CANL) - G83-2 (BATT) | W - Y | LOW-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CHECK COMBINATION METER ASSEMBLY
| *a | Rear view of wire harness connector
(to Combination Meter Assembly) |
Disconnect the combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G9-36 (CANH) - G9-35 (CANL) | SB - W | HIGH-level CAN bus wire - LOW-level CAN bus wire | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| G9-36 (CANH) - G9-27 (EP) | SB - W-B | HIGH-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G9-35 (CANL) - G9-27 (EP) | W - W-B | LOW-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G9-36 (CANH) - G9-21 (B) | SB - W | HIGH-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G9-35 (CANL) - G9-21 (B) | W - W | LOW-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CHECK AIRBAG SENSOR ASSEMBLY
| *a | Rear view of wire harness connector
(to Airbag Sensor Assembly) |
| *b | Front view of DLC3 |
Disconnect the airbag sensor assembly connector.
Type A: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type A)>PRECAUTION
Type B: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G42-13 (CANH) - G42-22 (CANL) | Y - W | HIGH-level CAN bus wire - LOW-level CAN bus wire | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| G42-13 (CANH) - G42-25 (E1) | Y - W-B | HIGH-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G42-22 (CANL) - G42-25 (E1) | W - W-B | LOW-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G42-13 (CANH) - G8-16 (BAT) | Y - G | HIGH-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G42-22 (CANL) - G8-16 (BAT) | W - G | LOW-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CHECK BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) (w/ VSC)
Disconnect the brake actuator assembly (skid control ECU) connector.
| *a | Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU]) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A4-22 (CANH) - A4-10 (CANL) | B - W | HIGH-level CAN bus wire - LOW-level CAN bus wire | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| A4-22 (CANH) - A4-25 (GND1) | B - W-B | HIGH-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A4-10 (CANL) - A4-25 (GND1) | W - W-B | LOW-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A4-22 (CANH) - A4-13 (BM) | B - R | HIGH-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| A4-10 (CANL) - A4-13 (BM) | W - R | LOW-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CHECK BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) (w/o VSC)
| *a | Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU]) |
Disconnect the brake actuator assembly (skid control ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A3-25 (CANH) - A3-14 (CANL) | B - W | HIGH-level CAN bus wire - LOW-level CAN bus wire | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| A3-25 (CANH) - A3-1 (GND1) | B - W-B | HIGH-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A3-14 (CANL) - A3-1 (GND1) | W - W-B | LOW-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| A3-25 (CANH) - A3-24 (+BM) | B - R | HIGH-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| A3-14 (CANL) - A3-24 (+BM) | W - R | LOW-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CHECK SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY (STEERING ANGLE SENSOR) (w/ VSC)
| *a | Front view of wire harness connector
(to Spiral with Sensor Cable Sub-assembly [Steering Angle Sensor]) |
Disconnect the spiral with sensor cable sub-assembly (steering angle sensor) connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G21-3 (CANH) - G21-2 (CANL) | BE - W | HIGH-level CAN bus wire - LOW-level CAN bus wire | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| G21-3 (CANH) - G21-1 (ESS) | BE - BR | HIGH-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G21-2 (CANL) - G21-1 (ESS) | W - BR | LOW-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G21-3 (CANH) - G21-5 (BAT) | BE - W | HIGH-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G21-2 (CANL) - G21-5 (BAT) | W - W | LOW-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (w/ Smart Entry and Start System)
Disconnect the certification ECU (smart key ECU assembly) connectors.
| *a | Front view of wire harness connector
(to Certification ECU [Smart Key ECU Assembly]) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G70-40 (CANH) - G70-18 (CANL) | G - W | HIGH-level CAN bus wire - LOW-level CAN bus wire | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| G70-40 (CANH) - G69-10 (E) | G - BR | HIGH-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G70-18 (CANL) - G69-10 (E) | W - BR | LOW-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G70-40 (CANH) - G69-1 (+B) | G - P | HIGH-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G70-18 (CANL) - G69-1 (+B) | W - P | LOW-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY (w/ Audio and Visual System [for Radio and Display Type])
| *a | Front view of wire harness connector
(to Radio and Display Receiver Assembly) |
Disconnect the radio and display receiver assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G37-9 (CANH) - G37-10 (CANL) | V - W | HIGH-level CAN bus wire - LOW-level CAN bus wire | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| G37-9 (CANH) - G40-7 (GND1) | V - BR | HIGH-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G37-10 (CANL) - G40-7 (GND1) | W - BR | LOW-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G37-9 (CANH) - G40-4 (+B1) | V - SB | HIGH-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G37-10 (CANL) - G40-4 (+B1) | W - SB | LOW-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CHECK 4 WHEEL DRIVE CONTROL ECU (for 4WD)
| *a | Front view of wire harness connector
(to 4 Wheel Drive Control ECU) |
Disconnect the 4 wheel drive control ECU connectors.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| C39-20 (CANH) - C39-40 (CANL) | R - W | HIGH-level CAN bus wire - LOW-level CAN bus wire | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| C39-20 (CANH) - C40-10 (GND) | R - W-B | HIGH-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| C39-40 (CANL) - C40-10 (GND) | W - W-B | LOW-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| C39-20 (CANH) - C39-21 (+B) | R - L | HIGH-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| C39-40 (CANL) - C39-21 (+B) | W - L | LOW-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY (for Automatic Air Conditioning System)
| *a | Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly) |
Disconnect the air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G33-11 (TX+) - G33-12 (TX-) | GR - W | HIGH-level CAN bus wire - LOW-level CAN bus wire | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| G33-11 (TX+) - G33-14 (GND) | GR - W-B | HIGH-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G33-12 (TX-) - G33-14 (GND) | W - W-B | LOW-level CAN bus wire - GND | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| G33-11 (TX+) - G33-21 (B) | GR - W | HIGH-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| G33-12 (TX-) - G33-21 (B) | W - W | LOW-level CAN bus wire - Battery positive (+) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |