Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD)
RM33J0E _57 Power Source / Network _038493 NETWORKING _0190453 CAN COMMUNICATION SYSTEM(for LHD) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD)  Air Conditioning Amplifier Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Air Conditioning Amplifier Communication Stop Mode Either condition is met:
·

"Air Conditioning Amplifier" is not displayed on "CAN Bus Check".

(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Air Conditioning Amplifier Communication Stop Mode" in "DTC Combination Table".

(Click here)


·

Power source circuit of air conditioning amplifier assembly

·

Air conditioning amplifier assembly ground circuit

·

Air conditioning amplifier assembly CAN branch wire or connector

·

Air conditioning amplifier assembly



WIRING DIAGRAM

C329214E03
5.646,0.76 6.104,0.958 0.458,0.198 10 false TX+ 5.635,1.313 6.094,1.51 0.458,0.198 10 false TX- 5.646,2.229 6.104,2.427 0.458,0.198 10 false B 5.656,3.031 6.115,3.229 0.458,0.198 10 false IG+ 5.646,3.875 6.104,4.073 0.458,0.198 10 false GND 4.729,4.771 7.021,5.073 2.292,0.302 10 false Air Conditioning Amplifier Assembly 4.719,4.594 5.292,4.896 0.573,0.302 10 false G33 5.302,0.604 5.615,0.802 0.313,0.198 10 false 11 5.302,1.208 5.615,1.406 0.313,0.198 10 false 12 5.281,2.104 5.594,2.302 0.313,0.198 10 false 21 5.344,2.917 5.656,3.115 0.313,0.198 10 false 1 5.302,3.74 5.615,3.938 0.313,0.198 10 false 14 3.927,2.052 4.823,2.281 0.896,0.229 10 false ECU-B NO.3 4.021,2.833 4.917,3.063 0.896,0.229 10 false IG1 NO.4 2.229,2.219 3.229,2.438 1,0.219 10 false from Battery 0.51,3.031 3.219,3.313 2.708,0.281 10 false from IG1 NO.1 Relay*1, Ignition Switch*2 1.677,0.625 1.99,0.823 0.313,0.198 10 false 10 1.688,1.208 2,1.406 0.313,0.198 10 false 20 0.25,1.667 0.708,1.865 0.458,0.198 10 false G68 0.26,1.844 2.688,2.188 2.427,0.344 10 false No. 2 CAN Junction Connector 0.313,4.76 3.021,5.042 2.708,0.281 10 false *1: w/ Smart Entry and Start System 0.323,5.104 3.031,5.385 2.708,0.281 10 false *2: w/o Smart Entry and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 5 seconds.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY CAN BRANCH WIRE)
a.
C240157C60
0.24,0.969 0.677,1.281 0.438,0.313 1.719,1.115 2.052,0.469 2.052,0.469 2.281,0.469 true 1.635,1.115 1.958,0.219 1.958,0.219 2.188,0.219 true 0.125,0.083 0.479,0.333 0.354,0.25 10 false *a 0.333,1.021 0.792,1.219 0.458,0.198 10 false G33 2.333,0.385 2.792,0.583 0.458,0.198 10 false TX+ 2.24,0.135 2.698,0.333 0.458,0.198 10 false TX-
*a Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the air conditioning amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G33-11 (TX+) - G33-12 (TX-) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY CAN BRANCH WIRE OR CONNECTOR (TX+, TX-)

2.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - BATTERY AND BODY GROUND)
a.
C240157C61
0.24,0.969 0.677,1.281 0.438,0.313 1.479,1.104 1.219,0.448 1.219,0.448 1,0.448 true 2.99,1.604 2.781,1.604 2.781,1.604 2.563,1.229 true 3.01,0.677 2.802,0.677 2.802,0.677 2.563,1.094 true 0.125,0.083 0.521,0.375 0.396,0.292 10 false *a 0.344,1.031 0.802,1.229 0.458,0.198 10 false G33 3.052,0.583 3.354,0.854 0.302,0.271 10 false IG+ 0.656,0.365 1.021,0.625 0.365,0.26 10 false GND 3.042,1.51 3.344,1.781 0.302,0.271 10 false B
*a Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G33-21 (B) - Body ground Always 11 to 14 V
G33-1 (IG+) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G33-14 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR