Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD) › 2015.06–2015.11
RM33J0E _57 Power Source / Network _038493 NETWORKING _0190453 CAN COMMUNICATION SYSTEM(for LHD) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD)  Short in CAN Bus Lines  


DESCRIPTION

There may be a short circuit between the CAN bus lines when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 53 Ω.

Symptom Trouble Area

*1: w/ VSC

*2: for Automatic Air Conditioning System

*3: w/ Smart Entry and Start System

*4: for 4WD

*5: w/ Audio and Visual System (for Radio and Display Type)

The resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 53 Ω.
·

Short between CAN bus lines

·

ECM

·

Brake actuator assembly (skid control ECU)

·

Spiral with sensor cable sub-assembly (steering angle sensor)*1

·

Air conditioning amplifier assembly*2

·

Airbag sensor assembly

·

Certification ECU (smart key ECU assembly)*3

·

4 wheel drive control ECU*4

·

Radio and display receiver assembly*5

·

Combination meter assembly

·

No. 1 CAN junction connector

·

No. 2 CAN junction connector

·

DLC3 CAN branch wire or connector



WIRING DIAGRAM

C329367E01
0.896,0.781 1.573,1.198 0.677,0.417 10 false CANH 0.917,1.323 1.594,1.74 0.677,0.417 10 false CANL 1.427,0.677 2.104,1.094 0.677,0.417 10 false 40 1.417,1.198 2.094,1.615 0.677,0.417 10 false 18 3.625,0.667 4.302,1.083 0.677,0.417 10 false 5 3.594,1.198 4.271,1.615 0.677,0.417 10 false 15 4.781,0.781 5.458,1.198 0.677,0.417 10 false G45 5.615,0.781 6.292,1.198 0.677,0.417 10 false G83 5.615,0.573 6.292,0.99 0.677,0.417 10 false 24*3 5.719,2.708 6.396,3.125 0.677,0.417 10 false 20 5.729,3.24 6.406,3.656 0.677,0.417 10 false 40 4.771,0.563 5.448,0.979 0.677,0.417 10 false 13*1 5.219,3.76 5.896,4.177 0.677,0.417 10 false C39 5.219,3.948 7.042,4.271 1.823,0.323 10 false 4 Wheel Drive Control ECU*6 5.198,0.781 5.875,1.198 0.677,0.417 10 false G85 3.615,2.719 4.292,3.135 0.677,0.417 10 false 4 2.646,0.656 3.323,1.073 0.677,0.417 10 false 3 1.417,3.26 2.094,3.677 0.677,0.417 10 false 10 3.594,3.26 4.271,3.677 0.677,0.417 10 false 14 5.198,0.563 5.875,0.979 0.677,0.417 10 false 17*2 2.573,1.198 3.25,1.615 0.677,0.417 10 false 13 6.01,0.656 6.688,1.073 0.677,0.417 10 false CANH 6.021,1.458 6.698,1.875 0.677,0.417 10 false CANL 0.906,2.823 1.583,3.24 0.677,0.417 10 false CANH 0.938,3.365 1.615,3.781 0.677,0.417 10 false CANL 2.656,2.708 3.333,3.125 0.677,0.417 10 false 7 2.594,3.24 3.271,3.656 0.677,0.417 10 false 17 0.146,1.74 0.823,2.156 0.677,0.417 10 false G70 0.146,1.917 2.271,2.448 2.125,0.531 10 false Certification ECU (Smart Key ECU Assembly)*4 6.229,1.792 6.906,2.208 0.677,0.417 10 false ECM 0.094,3.74 0.771,4.156 0.677,0.417 10 false G37 0.104,3.906 2.667,4.229 2.563,0.323 10 false Radio and Display Receiver Assembly*5 6.01,2.823 6.688,3.24 0.677,0.417 10 false CANH 6.01,3.365 6.688,3.781 0.677,0.417 10 false CANL 1.448,2.708 2.125,3.125 0.677,0.417 10 false 9 0.177,6.104 0.854,6.521 0.677,0.417 10 false G33 0.177,6.26 1.729,6.74 1.552,0.479 10 false Air Conditioning Amplifier Assembly*7 1.427,5.073 2.104,5.49 0.677,0.417 10 false 11 1.427,5.604 2.104,6.021 0.677,0.417 10 false 12 1.063,5.167 1.74,5.583 0.677,0.417 10 false TX+ 1.104,5.708 1.781,6.125 0.677,0.417 10 false TX- 2.385,6.271 3.063,6.688 0.677,0.417 10 false G68 2.385,6.448 3.625,6.938 1.24,0.49 10 false No. 2 CAN Junction Connector 4.781,1.313 5.458,1.729 0.677,0.417 10 false G45 5.198,1.313 5.875,1.729 0.677,0.417 10 false G85 5.615,1.313 6.292,1.729 0.677,0.417 10 false G83 4.76,1.094 5.438,1.51 0.677,0.417 10 false 14*1 5.188,1.094 5.865,1.51 0.677,0.417 10 false 28*2 5.615,1.094 6.292,1.51 0.677,0.417 10 false 23*3 0.208,7.104 2.771,7.427 2.563,0.323 10 false *1: for 2TR-FE 0.198,7.438 2.76,7.76 2.563,0.323 10 false *2: for 1GD-FTV, 2GD-FTV 0.198,7.76 2.76,8.083 2.563,0.323 10 false *3: for 1KD-FTV, 2KD-FTV 0.188,8.073 2.75,8.396 2.563,0.323 10 false *4: w/ Smart Entry and Start System 0.188,8.396 4.302,8.688 4.115,0.292 10 false *5: w/ Audio and Visual System (for Radio and Display Type) 3.51,7.083 6.073,7.406 2.563,0.323 10 false *6: for 4WD 3.51,7.375 6.073,7.698 2.563,0.323 10 false *7: for Automatic Air Conditioning System 2.583,5.073 3.26,5.49 0.677,0.417 10 false 10 2.594,5.604 3.271,6.021 0.677,0.417 10 false 20 3.615,5.073 4.292,5.49 0.677,0.417 10 false 6 3.583,5.604 4.26,6.021 0.677,0.417 10 false 16

C329368E01
0.938,1.417 1.75,1.823 0.813,0.406 10 false CANH 0.938,1.938 1.75,2.344 0.813,0.406 10 false CANL 1.427,1.313 2.24,1.719 0.813,0.406 10 false 13 1.438,1.823 2.25,2.229 0.813,0.406 10 false 22 0.135,2.344 0.948,2.75 0.813,0.406 10 false G42 0.146,2.51 1.938,2.781 1.792,0.271 10 false Airbag Sensor Assembly 5.656,1.406 6.469,1.813 0.813,0.406 10 false A4 1.448,3.302 2.26,3.708 0.813,0.406 10 false 6 1.427,3.844 2.24,4.25 0.813,0.406 10 false 14 5.229,1.406 6.042,1.813 0.813,0.406 10 false A3 0.833,4.406 1.646,4.813 0.813,0.406 10 false G8 0.771,4.573 1.583,4.979 0.813,0.406 10 false DLC3 2.844,6.344 3.656,6.75 0.813,0.406 10 false G67 2.854,6.51 4.833,6.823 1.979,0.313 10 false No. 1 CAN Junction Connector 5.188,1.198 6,1.604 0.813,0.406 10 false 25*1 5.604,1.198 6.417,1.604 0.813,0.406 10 false 22*2 5.469,2.365 7.063,2.833 1.594,0.469 10 false Brake Actuator Assembly (Skid Control ECU) 4.646,4.354 5.458,4.76 0.813,0.406 10 false G21 4.646,4.531 7.073,4.958 2.427,0.427 10 false Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor)*2 5.188,6.313 6,6.719 0.813,0.406 10 false G9 5.198,6.479 7.042,6.813 1.844,0.333 10 false Combination Meter Assembly 0.448,7.646 1.26,8.052 0.813,0.406 10 false *1: w/o VSC 0.448,7.969 1.26,8.375 0.813,0.406 10 false *2: w/ VSC 3.177,1.302 3.99,1.708 0.813,0.406 10 false 2 3.135,1.833 3.948,2.24 0.813,0.406 10 false 12 4.146,1.302 4.958,1.708 0.813,0.406 10 false 1 4.135,1.833 4.948,2.24 0.813,0.406 10 false 11 6.01,1.396 6.823,1.802 0.813,0.406 10 false CANH 5.979,1.958 6.792,2.365 0.813,0.406 10 false CANL 5.99,3.969 6.802,4.375 0.813,0.406 10 false CANL 6.021,6.073 6.833,6.479 0.813,0.406 10 false CANL 5.99,3.438 6.802,3.844 0.813,0.406 10 false CANH 6.01,5.24 6.823,5.646 0.813,0.406 10 false CANH 0.906,3.427 1.719,3.833 0.813,0.406 10 false CANH 0.938,3.948 1.75,4.354 0.813,0.406 10 false CANL 3.135,3.844 3.948,4.25 0.813,0.406 10 false 14 3.198,3.313 4.01,3.719 0.813,0.406 10 false 4 4.167,3.323 4.979,3.729 0.813,0.406 10 false 3 4.146,3.844 4.958,4.25 0.813,0.406 10 false 13 5.781,3.313 6.594,3.719 0.813,0.406 10 false 3 5.792,3.844 6.604,4.25 0.813,0.406 10 false 2 5.656,1.938 6.469,2.344 0.813,0.406 10 false A4 5.229,1.938 6.042,2.344 0.813,0.406 10 false A3 5.583,1.729 6.396,2.135 0.813,0.406 10 false 10*2 5.167,1.729 5.979,2.135 0.813,0.406 10 false 14*1 5.708,5.281 6.521,5.688 0.813,0.406 10 false 36 4.135,5.813 4.948,6.219 0.813,0.406 10 false 15 4.156,0.469 4.969,0.875 0.813,0.406 10 false 6 4.135,0.771 4.948,1.177 0.813,0.406 10 false 16 4.167,5.281 4.979,5.688 0.813,0.406 10 false 5 5.719,5.813 6.531,6.219 0.813,0.406 10 false 35

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the Precaution in the SRS.

Type A:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type A)>PRECAUTION

Type B:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION

·

When replacing the combination meter assembly, make sure to replace it with a new one.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the service bulletin.



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

·

Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.



PROCEDURE

1.CHECK FOR SHORT IN CAN BUS WIRES (DLC3 CAN BRANCH WIRE)
a.
C300827C24
0.115,0.99 0.521,1.25 0.406,0.26 1.948,0.917 1.552,0.385 1.552,0.385 1.406,0.385 true 1.938,1.49 2.052,1.906 2.052,1.906 2.167,1.906 true 0.135,0.115 0.448,0.271 0.313,0.156 10 false *a 0.219,1.052 0.5,1.219 0.281,0.167 10 false G8 1,0.333 1.49,0.479 0.49,0.146 10 false CANH 2.229,1.844 2.844,2.042 0.615,0.198 10 false CANL
*a Front view of DLC3


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the No. 1 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G8-6 (CANH) - G8-14 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

2.CONNECT CONNECTOR

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)

2.CONNECT CONNECTOR
a.

Reconnect the No. 1 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

3.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR SIDE)
3.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR SIDE)
a.
C300827C24
0.115,0.99 0.521,1.25 0.406,0.26 1.948,0.917 1.552,0.385 1.552,0.385 1.406,0.385 true 1.938,1.49 2.052,1.906 2.052,1.906 2.167,1.906 true 0.135,0.115 0.448,0.271 0.313,0.156 10 false *a 0.219,1.052 0.5,1.219 0.281,0.167 10 false G8 1,0.333 1.49,0.479 0.49,0.146 10 false CANH 2.229,1.844 2.844,2.042 0.615,0.198 10 false CANL
*a Front view of DLC3


Disconnect the No. 2 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G8-6 (CANH) - G8-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR)

NG

19.CONNECT CONNECTOR
4.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR)
a.

Measure the resistance according to the value(s) in the table below.

C300828C70
3.344,0.208 3.75,0.479 0.406,0.271 3.979,0.844 4.792,0.271 4.792,0.271 4.958,0.271 true 3.969,1.021 4.74,1.479 4.74,1.479 4.917,1.479 true 2.979,0.865 2.271,0.417 2.271,0.417 2.052,0.417 true 2.979,1.021 2.25,1.365 2.25,1.365 2.01,1.365 true 3.177,0.865 2.385,0.271 2.385,0.271 2.167,0.271 true 3.167,1.031 2.375,1.51 2.375,1.51 2.156,1.51 true 3.354,0.844 2.552,0.104 2.552,0.104 2.313,0.104 true 3.333,1.021 2.479,1.667 2.479,1.667 2.25,1.667 true 4.531,0.875 4.99,0.552 4.99,0.552 5.156,0.552 true 4.552,1.01 4.979,1.26 4.979,1.26 5.156,1.26 true 0.135,0.073 0.448,0.229 0.313,0.156 10 false *a 5,0.188 5.552,0.354 0.552,0.167 10 false CANH*e 1.5,0.333 2.031,0.479 0.531,0.146 10 false CANH*b 1.635,0.177 2.188,0.323 0.552,0.146 10 false CANH*c 1.781,0.031 2.323,0.198 0.542,0.167 10 false CANH*d 1.49,1.271 2.042,1.417 0.552,0.146 10 false CANL*b 1.615,1.417 2.188,1.573 0.573,0.156 10 false CANL*c 1.75,1.583 2.323,1.729 0.573,0.146 10 false CANL*d 4.969,1.406 5.5,1.552 0.531,0.146 10 false CANL*e 3.427,0.271 3.74,0.427 0.313,0.156 10 false G68 5.219,0.448 5.771,0.615 0.552,0.167 10 false CANH*f 5.219,1.198 5.75,1.344 0.531,0.146 10 false CANL*f
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to Certification ECU (Smart Key ECU Assembly) (w/ Smart Entry and Start System)
*c to 4 Wheel Drive Control ECU (for 4WD) *d to ECM
*e to Radio and Display Receiver Assembly (w/ Audio and Visual System [for Radio and Display Type]) *f to Air Conditioning Amplifier Assembly (for Automatic Air Conditioning System)


Standard Resistance:
Tester Connection Condition Specified Condition Connected to

*1: w/ Smart Entry and Start System

*2: for 4WD

*3: w/ Audio and Visual System (for Radio and Display Type)

*4: for Automatic Air Conditioning System

G68-3 (CANH) - G68-13 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Certification ECU (Smart Key ECU Assembly)*1
G68-4 (CANH) - G68-14 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher 4 Wheel Drive Control ECU*2
G68-5 (CANH) - G68-15 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω ECM
G68-7 (CANH) - G68-17 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Radio and Display Receiver Assembly*3
G68-10 (CANH) - G68-20 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Air Conditioning Amplifier Assembly*4



Result:
Result Proceed to
OK A
NG (to certification ECU [smart key ECU assembly] CAN branch wire) (w/ Smart Entry and Start System) B
NG (to 4 wheel drive control ECU CAN branch wire) (for 4WD) C
NG (to ECM CAN main wire) (for 2TR-FE) D
NG (to ECM CAN main wire) (for 1KD-FTV, 2KD-FTV) E
NG (to ECM CAN main wire) (for 1GD-FTV, 2GD-FTV) F
NG (to radio and display receiver assembly CAN branch wire) (w/ Audio and Visual System [for Radio and Display Type]) G
NG (to air conditioning amplifier assembly CAN branch wire) (for Automatic Air Conditioning System) H



A

REPLACE NO. 2 CAN JUNCTION CONNECTOR

B

5.CONNECT CONNECTOR

C

7.CONNECT CONNECTOR

D

9.CONNECT CONNECTOR

E

11.CONNECT CONNECTOR

F

13.CONNECT CONNECTOR

G

15.CONNECT CONNECTOR

H

17.CONNECT CONNECTOR
5.CONNECT CONNECTOR
a.

Reconnect the No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

6.CHECK FOR SHORT IN CAN BUS WIRES (CERTIFICATION ECU BRANCH WIRE)
6.CHECK FOR SHORT IN CAN BUS WIRES (CERTIFICATION ECU BRANCH WIRE)
a.
E271716C05
1.521,0.26 1.917,0.5 0.396,0.24 2.583,0.458 2.719,0.458 2.719,0.458 3.073,1.031 true 3.042,1.25 2.885,1.896 2.885,1.896 2.75,1.896 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 1.594,0.302 2.052,0.5 0.458,0.198 10 false G70 2.323,1.823 2.76,2.063 0.438,0.24 10 false CANH 2.198,0.385 2.635,0.625 0.438,0.24 10 false CANL
*a Front view of wire harness connector
(to Certification ECU [Smart Key ECU Assembly])


Disconnect the certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G70-40 (CANH) - G70-18 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CERTIFICATION ECU (CANH, CANL)

7.CONNECT CONNECTOR
a.

Reconnect the No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

8.CHECK FOR SHORT IN CAN BUS WIRES (4 WHEEL DRIVE CONTROL ECU BRANCH WIRE)
8.CHECK FOR SHORT IN CAN BUS WIRES (4 WHEEL DRIVE CONTROL ECU BRANCH WIRE)
a.
C317101C02
1.5,0.177 1.917,0.458 0.417,0.281 2.906,1.021 2.771,0.385 2.771,0.385 2.625,0.385 true 2.604,1.823 2.76,1.823 2.76,1.823 2.906,1.292 true 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 1.573,0.229 2.031,0.427 0.458,0.198 10 false C39 2.188,0.292 2.802,0.49 0.615,0.198 10 false CANH 2.219,1.74 2.833,1.938 0.615,0.198 10 false CANL
*a Front view of wire harness connector
(to 4 Wheel Drive Control ECU)


Disconnect the 4 wheel drive control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C39-20 (CANH) - C39-40 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

REPLACE 4 WHEEL DRIVE CONTROL ECU

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO 4 WHEEL DRIVE CONTROL ECU (CANH, CANL)

9.CONNECT CONNECTOR
a.

Reconnect the No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

10.CHECK FOR SHORT IN CAN BUS WIRES (ECM MAIN WIRE)
10.CHECK FOR SHORT IN CAN BUS WIRES (ECM MAIN WIRE)
a.
C317098C06
1.458,0.458 1.906,0.74 0.448,0.281 2.344,3.167 2.198,3.167 2.198,3.167 2.073,2 true 2.521,2.854 2.375,2.854 2.375,2.854 2.219,2.01 true 1.552,0.51 2.01,0.708 0.458,0.198 10 false G45 2.583,2.771 3.208,2.99 0.625,0.219 10 false CANL 2.427,3.063 3.052,3.302 0.625,0.24 10 false CANH 0.146,0.125 0.458,0.323 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G45-13 (CANH) - G45-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)

11.CONNECT CONNECTOR
a.

Reconnect the No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

12.CHECK FOR SHORT IN CAN BUS WIRES (ECM MAIN WIRE)
12.CHECK FOR SHORT IN CAN BUS WIRES (ECM MAIN WIRE)
a.
C317098C07
1.458,0.823 1.906,1.104 0.448,0.281 0.688,1.521 0.833,1.521 0.833,1.521 2.063,2.083 true 0.688,3.135 0.833,3.135 0.833,3.135 1.938,2.167 true 1.563,0.896 2.021,1.094 0.458,0.198 10 false G83 0.271,1.458 0.75,1.656 0.479,0.198 10 false CANH 0.26,3.063 0.708,3.26 0.448,0.198 10 false CANL 0.146,0.125 0.458,0.323 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G83-24 (CANH) - G83-23 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)

13.CONNECT CONNECTOR
a.

Reconnect the No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

14.CHECK FOR SHORT IN CAN BUS WIRES (ECM MAIN WIRE)
14.CHECK FOR SHORT IN CAN BUS WIRES (ECM MAIN WIRE)
a.
C317098C10
1.458,0.823 1.906,1.104 0.448,0.281 0.667,1.885 0.813,1.885 0.813,1.885 1.063,2.094 true 0.677,2.906 0.823,2.906 0.823,2.906 1.073,2.344 true 1.563,0.896 2.021,1.094 0.458,0.198 10 false G85 0.208,1.792 0.688,1.99 0.479,0.198 10 false CANH 0.24,2.823 0.688,3.021 0.448,0.198 10 false CANL 0.146,0.125 0.458,0.323 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G85-17 (CANH) - G85-28 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)

15.CONNECT CONNECTOR
a.

Reconnect the No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

16.CHECK FOR SHORT IN CAN BUS WIRES (RADIO AND DISPLAY RECEIVER ASSEMBLY BRANCH WIRE)
16.CHECK FOR SHORT IN CAN BUS WIRES (RADIO AND DISPLAY RECEIVER ASSEMBLY BRANCH WIRE)
a.
C310966C09
1.49,0.198 1.938,0.469 0.448,0.271 1.104,1.75 1.271,1.75 1.271,1.75 1.896,1.104 true 2.365,1.76 2.219,1.76 2.219,1.76 2.021,1.115 true 0.135,0.115 0.448,0.271 0.313,0.156 10 false *a 1.594,0.26 2.208,0.458 0.615,0.198 10 false G37 0.677,1.677 1.292,1.875 0.615,0.198 10 false CANH 2.438,1.698 3.052,1.896 0.615,0.198 10 false CANL
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Disconnect the radio and display receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G37-9 (CANH) - G37-10 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO RADIO AND DISPLAY RECEIVER ASSEMBLY (CANH, CANL)

17.CONNECT CONNECTOR
a.

Reconnect the No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

18.CHECK FOR SHORT IN CAN BUS WIRES (AIR CONDITIONING AMPLIFIER ASSEMBLY BRANCH WIRE)
18.CHECK FOR SHORT IN CAN BUS WIRES (AIR CONDITIONING AMPLIFIER ASSEMBLY BRANCH WIRE)
a.
C240157C57
0.24,0.969 0.677,1.281 0.438,0.313 1.719,1.115 2.052,0.469 2.052,0.469 2.281,0.469 true 1.635,1.115 1.958,0.219 1.958,0.219 2.188,0.219 true 0.073,0.083 0.385,0.24 0.313,0.156 10 false *a 0.344,1.063 0.802,1.26 0.458,0.198 10 false G33 2.333,0.406 2.792,0.604 0.458,0.198 10 false TX+ 2.24,0.156 2.698,0.354 0.458,0.198 10 false TX-
*a Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Disconnect the air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G33-11 (TX+) - G33-12 (TX-) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIR CONDITIONING AMPLIFIER ASSEMBLY (TX+, TX-)

19.CONNECT CONNECTOR
a.

Reconnect the No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

20.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION CONNECTOR)
20.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 1 CAN junction connector.

C300828C75
0.833,0.74 1.219,1 0.385,0.26 3.01,0.865 2.333,0.313 2.333,0.313 2.177,0.313 true 2.99,1.021 2.292,1.49 2.292,1.49 2.167,1.49 true 2.802,0.865 2.24,0.5 2.24,0.5 2.083,0.5 true 2.802,1.021 2.198,1.354 2.198,1.354 2.073,1.354 true 2.573,0.854 2.135,0.698 2.135,0.698 2,0.698 true 2.573,1.031 2.104,1.188 2.104,1.188 1.979,1.188 true 3.375,0.865 2.448,0.125 2.448,0.125 2.292,0.125 true 3.385,1.031 2.396,1.688 2.396,1.688 2.271,1.688 true 3.771,0.844 4.938,0.104 4.938,0.104 5.094,0.104 true 3.792,1.021 4.74,1.688 4.74,1.688 4.896,1.688 true 0.135,0.073 0.448,0.229 0.313,0.156 10 false *a 1.531,0.417 2.104,0.604 0.573,0.188 10 false CANH*c 1.604,0.229 2.167,0.427 0.563,0.198 10 false CANH*d 1.74,0.042 2.344,0.24 0.604,0.198 10 false CANH*e 1.552,1.271 2.083,1.458 0.531,0.188 10 false CANL*c 1.625,1.427 2.24,1.615 0.615,0.188 10 false CANL*d 1.75,1.604 2.396,1.76 0.646,0.156 10 false CANL*e 5.135,0.031 5.74,0.25 0.604,0.219 10 false CANH*f 4.979,1.615 5.635,1.781 0.656,0.167 10 false CANL*f 1.448,0.625 2.042,0.865 0.594,0.24 10 false CANH*b 1.427,1.094 2.031,1.292 0.604,0.198 10 false CANL*b 0.906,0.792 1.219,0.948 0.313,0.156 10 false G67
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to Brake Actuator Assembly (Skid Control ECU)
*c to Airbag Sensor Assembly *d to Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor) (w/ VSC)
*e to Combination Meter Assembly *f to No. 2 CAN Junction Connector



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

*: w/ VSC

G67-1 (CANH) - G67-11 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Brake Actuator Assembly (Skid Control ECU)
G67-2 (CANH) - G67-12 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Airbag Sensor Assembly
G67-3 (CANH) - G67-13 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor)*
G67-5 (CANH) - G67-15 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Combination Meter Assembly
G67-6 (CANH) - G67-16 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 2 CAN Junction Connector



Result:
Result Proceed to
OK A
NG (to brake actuator assembly [skid Control ECU] CAN branch wire) B
NG (to airbag sensor assembly CAN branch wire) C
NG (to spiral with sensor cable sub-assembly [steering angle sensor] CAN branch wire) (w/ VSC) D
NG (to combination meter assembly CAN main wire) E
NG (to No. 2 CAN junction connector CAN main wire) F



A

REPLACE NO. 1 CAN JUNCTION CONNECTOR

B

21.CONNECT CONNECTOR

C

23.CONNECT CONNECTOR

D

25.CONNECT CONNECTOR

E

27.CONNECT CONNECTOR

F

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

21.CONNECT CONNECTOR
a.

Reconnect the No. 1 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

22.CHECK FOR SHORT IN CAN BUS WIRES (SKID CONTROL ECU BRANCH WIRE)
22.CHECK FOR SHORT IN CAN BUS WIRES (SKID CONTROL ECU BRANCH WIRE)
a.
C317099C01
1.448,2.479 1.896,2.771 0.448,0.292 1.458,0.125 1.906,0.417 0.448,0.292 2.094,0.854 2.365,0.313 2.365,0.313 2.51,0.313 true 2.094,1.021 2.344,1.854 2.344,1.854 2.51,1.854 true 0.594,4.417 0.75,4.417 0.75,4.417 1.302,3.688 true 0.531,2.708 0.688,2.708 0.688,2.708 1.292,3.573 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 2.583,1.76 3.198,1.958 0.615,0.198 10 false CANH 2.594,0.219 3.208,0.417 0.615,0.198 10 false CANL 0.167,4.333 0.781,4.531 0.615,0.198 10 false CANH 0.146,2.646 0.76,2.844 0.615,0.198 10 false CANL 1.604,0.177 1.917,0.375 0.313,0.198 10 false A4 1.594,2.531 1.906,2.729 0.313,0.198 10 false A3 1.979,0.198 2.292,0.396 0.313,0.198 10 false *A 1.958,2.542 2.271,2.74 0.313,0.198 10 false *B
*A w/ VSC
*B w/o VSC
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])


Disconnect the brake actuator assembly (skid control ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ VSC
Tester Connection Condition Specified Condition
A4-22 (CANH) - A4-10 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω

w/o VSC
Tester Connection Condition Specified Condition
A3-25 (CANH) - A3-14 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SKID CONTROL ECU (CANH, CANL)

23.CONNECT CONNECTOR
a.

Reconnect the No. 1 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

24.CHECK FOR SHORT IN CAN BUS WIRES (AIRBAG SENSOR ASSEMBLY BRANCH WIRE)
24.CHECK FOR SHORT IN CAN BUS WIRES (AIRBAG SENSOR ASSEMBLY BRANCH WIRE)
a.
C210016C17
0.302,1 0.75,1.302 0.448,0.302 1.99,1.052 2.198,0.448 2.198,0.448 2.333,0.448 true 2.094,1.323 2.271,1.698 2.271,1.698 2.417,1.698 true 0.052,0.063 0.24,0.24 0.188,0.177 10 false *a 2.375,0.375 2.813,0.552 0.438,0.177 10 false CANH 0.375,1.073 0.656,1.25 0.281,0.177 10 false G42 2.458,1.615 2.896,1.792 0.438,0.177 10 false CANL
*a Rear view of wire harness connector
(to Airbag Sensor Assembly)


Disconnect the airbag sensor assembly connector.

Type A:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type A)>PRECAUTION

Type B:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G42-13 (CANH) - G42-22 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIRBAG SENSOR ASSEMBLY (CANH, CANL)

25.CONNECT CONNECTOR
a.

Reconnect the No. 1 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

26.CHECK FOR SHORT IN CAN BUS WIRES (STEERING ANGLE SENSOR BRANCH WIRE)
26.CHECK FOR SHORT IN CAN BUS WIRES (STEERING ANGLE SENSOR BRANCH WIRE)
a.
C300837C17
0.51,0.865 0.938,1.167 0.427,0.302 2.208,1.677 2.052,1.677 2.052,1.677 1.708,1.208 true 1.01,1.708 1.188,1.708 1.188,1.708 1.531,1.219 true 0.167,0.125 0.479,0.281 0.313,0.156 10 false *a 0.615,0.948 0.927,1.125 0.313,0.177 10 false G21 2.25,1.615 2.677,1.781 0.427,0.167 10 false CANH 0.667,1.635 1.125,1.792 0.458,0.156 10 false CANL
*a Front view of wire harness connector
(to Spiral with Sensor Cable Sub-assembly [Steering Angle Sensor])


Disconnect the spiral with sensor cable sub-assembly (steering angle sensor) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G21-3 (CANH) - G21-2 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

REPLACE SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY (STEERING ANGLE SENSOR)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY (CANH, CANL)

27.CONNECT CONNECTOR
a.

Reconnect the No. 1 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

28.CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY MAIN WIRE)
28.CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY MAIN WIRE)
a.
C221258C12
1.521,0.333 1.927,0.615 0.406,0.281 1.125,1.979 1.292,1.979 1.292,1.979 1.385,1.354 true 0.917,1.76 1.063,1.76 1.063,1.76 1.313,1.333 true 0.073,0.052 0.24,0.24 0.167,0.188 10 false *a 0.49,1.688 0.917,1.844 0.427,0.156 10 false CANH 0.708,1.906 1.104,2.063 0.396,0.156 10 false CANL 1.625,0.385 1.948,0.573 0.323,0.188 10 false G9
*a Rear view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G9-36 (CANH) - G9-35 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (CANH, CANL)