Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type)
RM33J0E _56 Audio / Visual / Telematics _038485 AUDIO / VIDEO _0191433 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Display Signal Circuit between Radio Receiver and Stereo Jack Adapter  


DESCRIPTION

The No. 1 stereo jack adapter assembly sends the display signal from an external device to the radio and display receiver assembly via this circuit.

WIRING DIAGRAM

E317766E03
2.323,2.365 2.479,2.563 0.156,0.198 10 false * 4.781,2.396 4.938,2.594 0.156,0.198 10 false * 5.979,2.25 6.344,2.521 0.365,0.271 10 false SG 5.979,1.635 6.344,1.906 0.365,0.271 10 false VV- 0.938,1.625 1.302,1.896 0.365,0.271 10 false VV- 0.938,1 1.302,1.271 0.365,0.271 10 false VV+ 5.979,1 6.344,1.271 0.365,0.271 10 false VV+ 5.698,0.938 6.063,1.208 0.365,0.271 10 false 13 5.688,1.531 6.052,1.802 0.365,0.271 10 false 14 5.688,2.146 6.052,2.417 0.365,0.271 10 false 12 3.792,2.135 4.156,2.406 0.365,0.271 10 false 1 1.323,1.521 1.688,1.792 0.365,0.271 10 false 11 1.333,0.917 1.698,1.188 0.365,0.271 10 false 6 3.781,1.51 4.146,1.781 0.365,0.271 10 false 9 3.781,0.927 4.146,1.198 0.365,0.271 10 false 8 0.281,2.583 0.646,2.854 0.365,0.271 10 false a1 0.281,2.74 1.438,3.365 1.156,0.625 10 false No. 1 Stereo Jack Adapter Assembly 1.625,2.729 3.417,3.219 1.792,0.49 10 false aG1 1.625,2.885 3.417,3.375 1.792,0.49 10 false Radio Wiring Sub-assembly 5.74,2.635 6.948,3.063 1.208,0.427 10 false G37 5.74,2.802 6.948,3.229 1.208,0.427 10 false Radio and Display Receiver Assembly 0.271,3.469 2.073,3.802 1.802,0.333 10 false *: Shielded 3.333,0.927 3.698,1.198 0.365,0.271 10 false 8 3.333,1.51 3.698,1.781 0.365,0.271 10 false 9 3.333,2.125 3.698,2.396 0.365,0.271 10 false 1

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - RADIO WIRING SUB-ASSEMBLY)
a.

Disconnect the G37 radio and display receiver assembly connector.


b.

Disconnect the aG1 radio wiring sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G37-13 (VV+) - aG1-8 Always Below 1 Ω
G37-14 (VV-) - aG1-9 Always Below 1 Ω
G37-12 (SG) - aG1-1 Always Below 1 Ω
G37-13 (VV+) or aG1-8 - Body ground Always 10 kΩ or higher
G37-14 (VV-) or aG1-9 - Body ground Always 10 kΩ or higher
G37-12 (SG) or aG1-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK RADIO WIRING SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK RADIO WIRING SUB-ASSEMBLY
a.
E317787C02
1.448,2.531 1.906,2.781 0.458,0.25 1.49,0.24 1.948,0.49 0.458,0.25 0.802,1.427 1,1.427 1,1.427 1.333,1.667 true 0.865,2.156 1.063,2.156 1.063,2.156 1.344,1.948 true 0.135,0.115 0.448,0.271 0.313,0.156 10 false *a 0.135,2.677 0.448,2.833 0.313,0.156 10 false *b 1.542,2.552 1.938,2.74 0.396,0.188 10 false aG1 1.635,0.271 2.031,0.458 0.396,0.188 10 false a1 0.49,1.323 1,1.531 0.51,0.208 10 false VV+ 0.563,2.031 1.073,2.24 0.51,0.208 10 false VV-
*a Front view of wire harness connector
(to No. 1 Stereo Jack Adapter Assembly)
*b Front view of wire harness connector
(to Vehicle Wire Harness)


Disconnect the No. 1 stereo jack adapter assembly connector.


b.

Disconnect the vehicle wire harness connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a1-6 (VV+) - aG1-8 Always Below 1 Ω
a1-11 (VV-) - aG1-9 Always Below 1 Ω
a1-6 (VV+) or aG1-8 - Body ground Always 10 kΩ or higher
a1-11 (VV-) or aG1-9 - Body ground Always 10 kΩ or higher
aG1-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE RADIO WIRING SUB-ASSEMBLY