Home › Engine / Hybrid System › 2GD-FTV COOLING › RADIATOR
RM33J0E _51 Engine / Hybrid System _038442 2GD-FTV COOLING _0191909 RADIATOR G

2GD-FTV COOLING  RADIATOR  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

CAUTION:
A343702

Do not remove the radiator reservoir cap sub-assembly while the engine and radiator assembly are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.


PROCEDURE

Hide 16471 1.CHECK RADIATOR RESERVOIR CAP SUB-ASSEMBLY

CAUTION:

Do not remove the radiator reservoir cap sub-assembly while the engine and radiator assembly are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.


a.
A301812C01
2.063,1.458 2.521,1.458 true 1.229,1.719 0.948,1.917 false 0.771,1.833 0.99,2.021 0.219,0.188 10 false *a 2.583,1.385 2.844,1.573 0.26,0.188 10 false *b
*a O-Ring
*b Rubber Packing


Measure the valve opening pressure.

i.

If there are water stains or foreign matter on the O-ring, clean it with water and finger scouring.


ii.

Check that the O-ring is not deformed, cracked or swollen.


iii.

Apply engine coolant to the O-ring and rubber packing before using a radiator cap tester.


iv.
A110393C19
0.354,1.135 0.354,0.563 0.354,0.563 0.563,0.563 false 1.542,1.042 1.542,0.615 1.542,0.615 1.729,0.615 false 1.813,0.51 2.115,0.698 0.302,0.188 10 false *a 0.656,0.49 0.958,0.698 0.302,0.208 10 false *1 0.698,2.167 1.021,2.365 0.323,0.198 10 false *b
*1 Radiator Reservoir Cap Sub-Assembly
*a Radiator Cap Tester
*b 30° or more


When using the radiator cap tester, tilt it 30° or more.


v.

Pump the radiator cap tester several times, and check the maximum pressure*.

Pump speed:

1 pump per second


*: Even if the radiator reservoir cap sub-assembly cannot maintain the maximum pressure, it is not a defect.

Judgment Criterion:
Item Specified Condition
Standard value
(for brand-new cap)
93 to 123 kPa (1.0 to 1.3 kgf/cm2, 13.5 to 18 psi)
Minimum standard value
(after using cap)
79 kPa (0.8 kgf/cm2, 11.4 psi)


If the maximum pressure is less than the minimum standard value, replace the radiator reservoir cap sub-assembly.



Hide 16400 2.INSPECT FINS FOR BLOCKAGE

A112201

a.

If the fins are clogged, wash them with water or a steam cleaner and dry them with compressed air.

NOTICE:
·

To avoid damaging the fins, the injection direction should be at right angles to the core surface.

·

If the steam cleaner is too close to the core, there is a possibility of damaging the fins, so maintain the following injection distances.

Standard Injection Distance:
Injection Pressure Specified Condition
2942 to 4903 kPa
(30.0 to 50.0 kgf/cm2, 427 to 711 psi)
300 mm (11.8 in.)
4903 to 7845 kPa
(50.0 to 80.0 kgf/cm2, 711 to 1138 psi)
500 mm (19.7 in.)


·

If the fins are bent, straighten them with a screwdriver or pliers.

·

Do not expose electronic components to water.




b.

Dry the fins with compressed air.