Home › Engine / Hybrid System › 1KD-FTV STARTING › STARTER(for 2.2 kW Type)
RM33J0E _51 Engine / Hybrid System _038435 1KD-FTV STARTING _0191924 STARTER(for 2.2 kW Type) G

1KD-FTV STARTING  STARTER(for 2.2 kW Type)  INSPECTION  


PROCEDURE

Hide 28100 1.INSPECT STARTER ASSEMBLY

CAUTION:

As a large electric current passes through the cable during this inspection, a thick cable must be used. Otherwise, the cable may become hot and cause injury.


NOTICE:

These tests must be performed within 3 to 5 seconds to prevent the coil from burning out.


a.

Mount the starter assembly in a vise between aluminum plates.


b.

Perform pull-in test.

i.

Remove the nut and disconnect the lead wire from terminal C.


ii.
A347880C01
0.729,0.385 0.927,0.385 0.927,0.385 1.115,0.698 false 1.885,0.271 2.563,0.271 2.563,0.271 2.75,0.583 true 2.844,1.042 3.146,2.552 3.146,2.552 2.854,2.563 true 0.5,0.302 0.813,0.5 0.313,0.198 10 false *a 1.615,0.208 1.927,0.406 0.313,0.198 10 false *b 2.635,2.49 2.948,2.688 0.313,0.198 10 false *c
*a Starter Body
*b Terminal 50
*c Terminal C


Connect the battery to the magnet starter switch assembly as shown in the illustration. Then check that the clutch pinion gear moves outward.

If the clutch pinion gear does not move, replace the magnet starter switch assembly.



c.

Perform holding test.

i.
A347881C02
0.917,0.333 1.667,0.333 1.667,0.333 2.917,0.958 true 0.625,0.281 0.938,0.479 0.313,0.198 10 false *a
*a Terminal C
V100135

Disconnect


When the battery is connected as above with the clutch pinion gear out, disconnect the negative (-) lead from terminal C. Check that the pinion gear remains out.

If the clutch pinion gear returns inward, replace the magnet starter switch assembly.



d.

Inspect clutch pinion gear return.

i.
A347882C01
0,0 0,0 false
V100135

Disconnect
V100136

Return Inward


Disconnect the negative (-) lead from the starter body. Check that the clutch pinion gear returns inward.

If the clutch pinion gear does not return inward, replace the magnet starter switch assembly.



e.

Perform operation test without load.

i.
A347871

Connect the lead wire to terminal C with the nut.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


ii.
A347883C01
1.667,0.25 2,0.25 2,0.25 2.333,0.75 true 2.583,0.167 2.917,0.167 false 0.531,0.917 0.865,0.917 false 2.76,0.698 2.781,1.083 2.781,1.083 2.958,1.083 true 3.01,0.979 3.323,1.177 0.313,0.198 10 false *c 0.354,0.833 0.667,1.031 0.313,0.198 10 false *a 1.438,0.167 1.75,0.365 0.313,0.198 10 false *b 2.417,0.083 2.729,0.281 0.313,0.198 10 false *d
*a Starter Body
*b Terminal 50
*c Terminal 30
*d AC/DC 400A Probe


Connect the battery and an ammeter (AC/DC 400A probe) to the starter assembly as shown in the illustration.


iii.

Check that the starter rotates smoothly and steadily while the clutch pinion gear is extended. Then measure the current.

Standard current:

120 A or less at 11 V


If the result is not as specified, replace the starter assembly.



Hide 2.INSPECT STARTER DRIVE HOUSING

A348840C01
0,0 0,0 false
V100135

Free
V100136

Lock


a.

Rotate the clutch pinion gear clockwise and check that it turns freely. Try to rotate the clutch pinion gear counterclockwise and check that it locks.

If the result is not as specified, replace the starter drive housing.


b.

Turn the clutch pinion gear by hand while applying inward force and check the movement of the bearing.

If resistance is felt or the bearing sticks, replace the starter drive housing.


Hide 28160 3.INSPECT STARTER ARMATURE ASSEMBLY

a.
A352339C01
1.146,1.208 0.5,1.208 true 2.698,1.271 2.052,1.271 true 0.281,1.146 0.594,1.344 0.313,0.198 10 false *b 2.75,1.188 3.063,1.385 0.313,0.198 10 false *a
*a Segment
*b Coil Core


Measure the resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Segment - Segment Always Below 2.9 Ω
Segment - Coil Core 1 MΩ or higher


If the result is not as specified, replace the starter armature assembly.



b.
A082645

Inspect the commutator circle runout.

i.

Place the commutator on V-blocks.


ii.

Using a dial indicator, measure the circle runout.

Standard runout:

0.05 mm (0.00197 in.)


Maximum runout:

0.06 mm (0.00236 in.)


If the runout is more than the maximum, replace the starter armature assembly.



c.
A105696

Using a vernier caliper, measure the commutator diameter.

Standard diameter:

29.4 mm (1.157 in.)


Minimum diameter:

28.9 mm (1.138 in.)


If the diameter is less than the minimum, replace the starter armature assembly.


d.
A105577

Using a vernier caliper, measure the undercut depth of the commutator.

Standard depth:

1.1 mm (0.0433 in.)


Minimum depth:

0.5 mm (0.020 in.)


If the depth is less than the minimum, replace the starter armature assembly.


Hide 28140 4.INSPECT STARTER BRUSH HOLDER ASSEMBLY

a.
A344146

Using a vernier caliper, measure the brush length.

Standard length:

15.6 mm (0.614 in.)


Minimum length:

10.6 mm (0.417 in.)


If the length is less than the minimum, replace the starter brush holder assembly.


b.
A344147N01
2.292,0.448 2.427,0.167 2.427,0.167 2.615,0.167 false 0.865,2.042 1.031,2.042 1.031,2.042 1.198,1.906 false 0.573,1.063 0.833,1.063 false 2.656,1.281 2.917,1.281 false 2.688,0.083 2.844,0.281 0.156,0.198 10 false A 0.76,1.969 0.917,2.167 0.156,0.198 10 false D 2.958,1.208 3.115,1.406 0.156,0.198 10 false C 0.458,0.979 0.615,1.177 0.156,0.198 10 false B

Check the resistance.

i.

Measure the resistance between the brushes.

Standard Resistance:
Tester Connection Condition Specified Condition
A - C
A - D
B - C
B - D
Always 1 MΩ or higher
A - B
C - D
Below 1 Ω


If the result is not as specified, replace the starter brush holder assembly.



Hide 28150 5.INSPECT MAGNET STARTER SWITCH ASSEMBLY

a.
C322569C01
0.5,0.813 0.75,0.813 0.75,0.813 0.906,1.042 false 2.198,0.385 2.448,0.385 2.448,0.385 2.604,0.615 false 1.448,0.646 1.698,0.646 1.698,0.646 1.854,0.875 false 0.292,0.708 0.604,0.906 0.313,0.198 10 false *a 1.219,0.552 1.531,0.75 0.313,0.198 10 false *b 2.042,0.313 2.354,0.51 0.313,0.198 10 false *c
*a Magnet Starter Switch Body
*b Spring
*c Plunger


Check the plunger.

i.

Install the plunger and spring onto the magnet starter switch body.


ii.
C322570

Push in the plunger and check that it returns quickly to its original position.

If the result is not as specified, replace the magnet starter switch assembly.



b.
A352340C01
0.417,0.417 0.74,0.417 0.74,0.417 1.552,0.896 true 1.646,1.875 1.969,1.875 1.969,1.875 1.917,1.396 true 3.115,1.74 3.344,1.74 3.344,1.74 2.885,1.24 true 0.198,0.302 0.51,0.5 0.313,0.198 10 false *a 1.438,1.781 1.75,1.979 0.313,0.198 10 false *b 2.896,1.656 3.208,1.854 0.313,0.198 10 false *c
*a Terminal 50
*b Terminal C
*c Magnet Starter Switch Body


Check if the pull-in coil has an open circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 50 - Terminal C Always Below 0.305 Ω
Terminal 50 - Magnet Starter Switch Body Below 0.910 Ω


If the result is not as specified, replace the magnet starter switch assembly.