Home › Engine / Hybrid System › 1KD-FTV STARTING › STARTER(for 2.2 kW Type)
RM33J0E _51 Engine / Hybrid System _038435 1KD-FTV STARTING _0191924 STARTER(for 2.2 kW Type) A

1KD-FTV STARTING  STARTER(for 2.2 kW Type)  DISASSEMBLY  


PROCEDURE

Hide 28150 1.REMOVE MAGNET STARTER SWITCH ASSEMBLY

a.
C322557

Remove the nut and disconnect the lead wire from terminal C.


b.
C322558

Remove the 2 screws holding the magnet starter switch assembly to the starter drive housing.


c.

Remove the return spring and magnet starter switch assembly.


d.
C326510C01
1.031,1.833 0.927,1.365 0.927,1.365 0.583,1.365 false 1.458,1.406 1.771,1.406 1.771,1.406 2.302,1.76 true 0.385,1.25 0.698,1.448 0.313,0.198 10 false *a 1.229,1.313 1.542,1.51 0.313,0.198 10 false *b
*a Hook
*b Pinion Driver Lever


While lifting the plunger, remove the hook from the pinion drive lever, then remove the plunger.


e.
C322560

Remove the plate from the plunger.


Hide 28120 2.REMOVE STARTER YOKE ASSEMBLY

a.
C322561

Using a 7 mm socket wrench, remove the 2 bolts and starter yoke assembly from the starter drive housing.


b.
C322562C01
0.365,1.063 0.573,1.063 0.573,1.063 0.74,1.198 false 1.125,0.24 1.333,0.24 1.333,0.24 1.5,0.375 false 0.875,0.156 1.188,0.354 0.313,0.198 10 false *2 0.146,0.99 0.458,1.188 0.313,0.198 10 false *1
*1 Starter Armature Plate
*2 Starter Drive Housing


Remove the starter armature plate from the starter drive housing.


Hide 28160 3.REMOVE STARTER ARMATURE ASSEMBLY

a.
A344140C01
0.885,0.708 1.135,0.708 1.135,0.708 1.365,0.938 false 2.115,1.115 2.427,1.365 2.427,1.365 2.667,1.365 true 0.583,0.625 0.896,0.823 0.313,0.198 10 false *1 2.74,1.271 3.052,1.469 0.313,0.198 10 false *2
*1 Starter Yoke Assembly
*2 Starter Armature Assembly


Remove the starter armature assembly together with the starter brush holder assembly from the starter yoke assembly.


Hide 28140 4.INSPECT STARTER BRUSH HOLDER ASSEMBLY

a.

Check whether the springs of the starter brush holder are contacting the brushes.


b.

Check that the springs of the starter brush holder are free from dirt and rust.


Hide 28140 5.REMOVE STARTER BRUSH HOLDER ASSEMBLY

a.
A367421

Using a screwdriver, pry the end of the spring away from each brush and pull out the 4 brushes from the brush holder so that they are held in place by the springs.

NOTICE:

Do not apply excessive force to the brushes. Otherwise, the brushes and brush holder may become damaged or bent.



b.

Remove the starter brush holder assembly.


c.
A344161

Remove the washer from the starter armature assembly.


Hide 6.REMOVE RUBBER SEAL

a.
C326516C01
0.948,0.542 1.208,0.542 1.208,0.542 1.625,0.75 true 0.75,0.469 1.063,0.667 0.313,0.198 10 false *1
*1 Rubber Seal


Remove the rubber seal from the starter drive housing.