28100
1.INSPECT STARTER ASSEMBLY
As a large electric current passes through the cable during this inspection, a thick cable must be used. Otherwise, the cable may become hot and cause injury.
These tests must be performed within 3 to 5 seconds to prevent the coil from burning out.
Mount the starter assembly in a vise between aluminum plates.
Perform pull-in test.
Remove the nut and disconnect the lead wire from terminal C.
| *a | Starter Body |
| *b | Terminal 50 |
| *c | Terminal C |
Connect the battery to the magnet starter switch assembly as shown in the illustration. Then check that the clutch pinion gear moves outward.
If the clutch pinion gear does not move, replace the magnet starter switch assembly.
Perform holding test.
| *a | Terminal C |
|
Disconnect |
When the battery is connected as above with the clutch pinion gear out, disconnect the negative (-) lead from terminal C. Check that the pinion gear remains out.
If the clutch pinion gear returns inward, replace the magnet starter switch assembly.
Inspect clutch pinion gear return.
|
Disconnect |
|
Return Inward |
Disconnect the negative (-) lead from the starter body. Check that the clutch pinion gear returns inward.
If the clutch pinion gear does not return inward, replace the magnet starter switch assembly.
Perform operation test without load.
Connect the lead wire to terminal C with the nut.
| *a | Starter Body |
| *b | Terminal 50 |
| *c | Terminal 30 |
| *d | AC/DC 400A Probe |
Connect the battery and an ammeter (AC/DC 400A probe) to the starter assembly as shown in the illustration.
Check that the starter rotates smoothly and steadily while the clutch pinion gear is extended. Then measure the current.
120 A or less at 11 V
If the result is not as specified, replace the starter assembly.
2.INSPECT STARTER DRIVE HOUSING
|
Free |
|
Lock |
Rotate the clutch pinion gear clockwise and check that it turns freely. Try to rotate the clutch pinion gear counterclockwise and check that it locks.
If the result is not as specified, replace the starter drive housing.
Turn the clutch pinion gear by hand while applying inward force and check the movement of the bearing.
If resistance is felt or the bearing sticks, replace the starter drive housing.
28160
3.INSPECT STARTER ARMATURE ASSEMBLY
| *a | Segment |
| *b | Coil Core |
Measure the resistance.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Segment - Segment | Always | Below 2.9 Ω |
| Segment - Coil Core | 1 MΩ or higher |
If the result is not as specified, replace the starter armature assembly.
Inspect the commutator circle runout.
Place the commutator on V-blocks.
Using a dial indicator, measure the circle runout.
0.05 mm (0.00197 in.)
0.06 mm (0.00236 in.)
If the runout is more than the maximum, replace the starter armature assembly.
Using a vernier caliper, measure the commutator diameter.
29.4 mm (1.157 in.)
28.9 mm (1.138 in.)
If the diameter is less than the minimum, replace the starter armature assembly.
Using a vernier caliper, measure the undercut depth of the commutator.
1.1 mm (0.0433 in.)
0.5 mm (0.020 in.)
If the depth is less than the minimum, replace the starter armature assembly.
28140
4.INSPECT STARTER BRUSH HOLDER ASSEMBLY
Using a vernier caliper, measure the brush length.
15.6 mm (0.614 in.)
10.6 mm (0.417 in.)
If the length is less than the minimum, replace the starter brush holder assembly.
Check the resistance.
Measure the resistance between the brushes.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A - C
A - D B - C B - D |
Always | 1 MΩ or higher |
| A - B
C - D |
Below 1 Ω |
If the result is not as specified, replace the starter brush holder assembly.
28150
5.INSPECT MAGNET STARTER SWITCH ASSEMBLY
| *a | Magnet Starter Switch Body |
| *b | Spring |
| *c | Plunger |
Check the plunger.
Install the plunger and spring onto the magnet starter switch body.
Push in the plunger and check that it returns quickly to its original position.
If the result is not as specified, replace the magnet starter switch assembly.
| *a | Terminal 50 |
| *b | Terminal C |
| *c | Magnet Starter Switch Body |
Check if the pull-in coil has an open circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Terminal 50 - Terminal C | Always | Below 0.305 Ω |
| Terminal 50 - Magnet Starter Switch Body | Below 0.910 Ω |
If the result is not as specified, replace the magnet starter switch assembly.