Home › Vehicle Interior › HEATING / AIR CONDITIONING › RELAY
RM33J0E _58 Vehicle Interior _038504 HEATING / AIR CONDITIONING _0192217 RELAY G

HEATING / AIR CONDITIONING  RELAY  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 87299 1.INSPECT HEATER RELAY (for Manual Air Conditioning System)

a.
B106753C01
2.51,0.802 2.51,0.615 true 2.854,1.177 3.042,1.177 true 2.5,1.521 2.5,1.719 true 2.073,1.208 2.073,1.74 true 2.479,1.042 1.802,1.042 true 0.813,0.146 0.906,0.344 0.094,0.198 10 false 4 0.333,0.792 0.427,0.99 0.094,0.198 10 false 5 1.271,0.792 1.365,0.99 0.094,0.198 10 false 3 0.333,1.604 0.427,1.802 0.094,0.198 10 false 1 1.281,1.594 1.375,1.792 0.094,0.198 10 false 2 1.677,0.969 1.771,1.167 0.094,0.198 10 false 4 3.083,1.094 3.177,1.292 0.094,0.198 10 false 5 2.031,1.75 2.125,1.948 0.094,0.198 10 false 3 2.479,0.438 2.573,0.635 0.094,0.198 10 false 1 2.479,1.75 2.573,1.948 0.094,0.198 10 false 2 0.083,0.052 0.375,0.26 0.292,0.208 10 false *a
*a Component without harness connected
(Heater Relay)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 4 Battery voltage is not applied between terminals 1 and 2 Below 1 Ω
3 - 5 Battery voltage is not applied between terminals 1 and 2 10 kΩ or higher
3 - 4 Battery voltage is applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Battery voltage is applied between terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the heater relay.


Hide 85934 2.INSPECT MAGNET-CLUTCH RELAY

a.
B060778C11
2.229,0.656 2.073,0.75 false 2.563,0.76 2.406,0.854 false 2.323,1.167 2.167,1.26 false 2.458,1.49 2.302,1.583 false 0.208,1.333 0.365,1.531 0.156,0.198 10 false 1 1.219,1.302 1.375,1.5 0.156,0.198 10 false 2 0.229,0.771 0.385,0.969 0.156,0.198 10 false 3 1.208,0.771 1.365,0.969 0.156,0.198 10 false 5 2.24,0.552 2.396,0.75 0.156,0.198 10 false 1 2.292,0.802 2.448,1 0.156,0.198 10 false 2 2.021,1.219 2.177,1.417 0.156,0.198 10 false 5 2.542,1.354 2.698,1.552 0.156,0.198 10 false 3 0.073,0.063 0.385,0.219 0.313,0.156 10 false *a
*a Component without harness connected
(Magnet-clutch Relay)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage is not applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Battery voltage is applied between terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the magnet-clutch relay.