Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW REGULATOR MOTOR(for Front Door)
RM33J0E _59 Vehicle Exterior _038507 WINDOW / GLASS _0192277 POWER WINDOW REGULATOR MOTOR(for Front Door) G

WINDOW / GLASS  POWER WINDOW REGULATOR MOTOR(for Front Door)  INSPECTION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedures listed below are for LHD vehicles.



PROCEDURE

Hide 85720C 1.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

a.

w/ Jam Protection Function:

NOTICE:
·

Do not apply positive (+) battery voltage to any terminals, except terminal 2 (B), to avoid damaging the pulse sensor inside the motor.

·

Perform initialization of the power window system after removing, inspecting or replacing the power window regulator motor assembly LH.



i.
B405918C03
1.552,0.885 1.031,0.75 true 1.969,1.26 2.479,1.354 true 1.5,1.271 1.063,1.406 true 1.927,0.885 2.448,0.76 true 1.146,4.479 1.458,4.635 0.313,0.156 10 false *b 0.385,0.302 0.698,0.458 0.313,0.156 10 false *a 0.875,0.656 1.031,0.854 0.156,0.198 10 false B 2.552,1.281 3.167,1.479 0.615,0.198 10 false DOWN 0.813,1.344 1.125,1.542 0.313,0.198 10 false UP 2.542,0.667 3,0.865 0.458,0.198 10 false GND
*a Component without harness connected
(Power Window Regulator Motor Assembly LH)
*b Motor Gear
V100135

Clockwise
V100136

Counterclockwise


Check that the motor gear rotates smoothly as follows.

OK:
Measurement Condition Specified Condition
1.

Connect the positive (+) lead of the battery to terminal 2 (B) and the negative (-) lead to terminal 1 (GND), and hold for 3 sec. or more.

2.

While terminals 2 (B) and 1 (GND) are connected, connect the negative (-) lead of the battery to terminal 10 (UP).

3.

After disconnecting the negative (-) lead of the battery from terminal 10 (UP), connect terminal 10 (UP) to the negative (-) lead of the battery again within 1 sec.


Motor gear rotates clockwise (UP)
1.

Connect the positive (+) lead of the battery to terminal 2 (B) and the negative (-) lead to terminal 1 (GND), and hold for 3 sec. or more.

2.

While terminals 2 (B) and 1 (GND) are connected, connect the negative (-) lead of the battery to terminal 7 (DOWN).

3.

After disconnecting the negative (-) lead of the battery from terminal 7 (DOWN), connect terminal 7 (DOWN) to the negative (-) lead of the battery again within 1 sec.


Motor gear rotates counterclockwise (DOWN)

If the result is not as specified, replace the power window regulator motor assembly LH.



b.

w/o Jam Protection Function:

i.
B405919C01
1.188,4.479 1.5,4.635 0.313,0.156 10 false *b 0.375,0.323 0.688,0.479 0.313,0.156 10 false *a
*a Component without harness connected
(Power Window Regulator Motor Assembly LH)
*b Motor Gear
V100135

Clockwise
V100136

Counterclockwise


Apply battery voltage to connector terminals 1 and 2.

NOTICE:

Do not apply battery voltage to any terminals except terminals 1 and 2.



ii.

Check that the motor gear rotates smoothly as follows.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 1
Battery negative (-) → 2
Motor gear rotates counterclockwise
Battery positive (+) → 2
Battery negative (-) → 1
Motor gear rotates clockwise


If the result is not as specified, replace the power window regulator motor assembly LH.



Hide 85710D 2.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

NOTICE:
·

Do not apply positive (+) battery voltage to any terminals, except terminal 2 (B), to avoid damaging the pulse sensor inside the motor.

·

Perform initialization of the power window system after removing, inspecting or replacing the power window regulator motor assembly RH.



a.
B405917C01
1.531,0.885 0.948,0.771 true 1,1.396 1.49,1.24 true 1.969,1.25 2.5,1.458 true 1.917,0.885 2.479,0.781 true 2.104,4.469 2.417,4.625 0.313,0.156 10 false *b 0.448,0.302 0.76,0.458 0.313,0.156 10 false *a 2.552,1.385 3.167,1.583 0.615,0.198 10 false DOWN 0.75,1.354 1.063,1.552 0.313,0.198 10 false UP 0.813,0.688 0.969,0.885 0.156,0.198 10 false B 2.521,0.698 2.979,0.896 0.458,0.198 10 false GND
*a Component without harness connected
(Power Window Regulator Motor Assembly RH)
*b Motor Gear
V100135

Clockwise
V100136

Counterclockwise


w/ Jam Protection Function:

OK:
Measurement Condition Specified Condition
1.

Connect the positive (+) lead of the battery to terminal 2 (B) and the negative (-) lead to terminal 1 (GND), and hold for 3 sec. or more.

2.

While terminals 2 (B) and 1 (GND) are connected, connect the negative (-) lead of the battery to terminal 10 (UP).

3.

After disconnecting the negative (-) lead of the battery from terminal 10 (UP), connect terminal 10 (UP) to the negative (-) lead of the battery again within 1 sec.


Motor gear rotates clockwise (UP)
1.

Connect the positive (+) lead of the battery to terminal 2 (B) and the negative (-) lead to terminal 1 (GND), and hold for 3 sec. or more.

2.

While terminals 2 (B) and 1 (GND) are connected, connect the negative (-) lead of the battery to terminal 7 (DOWN).

3.

After disconnecting the negative (-) lead of the battery from terminal 7 (DOWN), connect terminal 7 (DOWN) to the negative (-) lead of the battery again within 1 sec.


Motor gear rotates counterclockwise (DOWN)

If the result is not as specified, replace the power window regulator motor assembly RH.

i.

Check that the motor gear rotates smoothly as follows.



b.
B405920C01
2.073,4.479 2.385,4.635 0.313,0.156 10 false *b 0.375,0.271 0.688,0.427 0.313,0.156 10 false *a
*a Component without harness connected
(Power Window Regulator Motor Assembly RH)
*b Motor Gear
V100135

Clockwise
V100136

Counterclockwise


w/o Jam Protection Function:

i.

Apply battery voltage to connector terminals 1 and 2.

NOTICE:

Do not apply battery voltage to any terminals except terminals 1 and 2.



ii.

Check that the motor gear rotates smoothly as follows.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 1
Battery negative (-) → 2
Motor gear rotates counterclockwise
Battery positive (+) → 2
Battery negative (-) → 1
Motor gear rotates clockwise


If the result is not as specified, replace the power window regulator motor assembly RH.