Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)
RM33J0E _56 Audio / Visual / Telematics _038485 AUDIO / VIDEO _0193314 AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)  Microphone Circuit between Microphone and Radio Receiver  


DESCRIPTION

·

The radio receiver assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.

·

Using this circuit, the radio receiver assembly sends power to the map light assembly (telephone microphone assembly), and the map light assembly (telephone microphone assembly) sends microphone signals to the radio receiver assembly.


WIRING DIAGRAM

E323304E04
0.948,0.615 1.688,1.125 0.74,0.51 10 false Telephone Microphone Assembly 2.125,0.521 2.646,0.76 0.521,0.24 10 false MCO+ 2.156,1.156 2.677,1.396 0.521,0.24 10 false MCO- 2.135,1.781 2.656,2.021 0.521,0.24 10 false MACC 2.625,0.531 3.146,0.771 0.521,0.24 10 false 14 2.646,1.146 3.167,1.385 0.521,0.24 10 false 13 2.646,1.771 3.167,2.01 0.521,0.24 10 false 15 0.708,2.927 1.229,3.167 0.521,0.24 10 false Q3 0.729,3.083 2.073,3.302 1.344,0.219 10 false Map Light Assembly 5.542,0.531 6.063,0.771 0.521,0.24 10 false 5 5.521,1.135 6.042,1.375 0.521,0.24 10 false 19 5.552,1.76 6.073,2 0.521,0.24 10 false 4 5.521,2.375 6.042,2.615 0.521,0.24 10 false 18 5.823,0.635 6.344,0.875 0.521,0.24 10 false MIN+ 5.823,1.24 6.344,1.479 0.521,0.24 10 false MIN- 5.833,1.865 6.354,2.104 0.521,0.24 10 false MACC 5.823,2.479 6.344,2.719 0.521,0.24 10 false SGND 5.521,2.948 6.042,3.188 0.521,0.24 10 false G113 5.542,3.104 7.156,3.302 1.615,0.198 10 false Radio Receiver Assembly 3.313,2.625 3.927,2.781 0.615,0.156 10 false Shielded 4.542,2.635 5.156,2.792 0.615,0.156 10 false Shielded

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
a.

Disconnect the G113 radio receiver assembly connector.


b.

Disconnect the Q3 map light assembly (telephone microphone assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G113-4 (MACC) - Q3-15 (MACC) Always Below 1 Ω
G113-5 (MIN+) - Q3-14 (MCO+) Always Below 1 Ω
G113-19 (MIN-) - Q3-13 (MCO-) Always Below 1 Ω
G113-18 (SGND) - Body ground Always 10 kΩ or higher
G113-4 (MACC) or Q3-15 (MACC) - Body ground Always 10 kΩ or higher
G113-5 (MIN+) or Q3-14 (MCO+) - Body ground Always 10 kΩ or higher
G113-19 (MIN-) or Q3-13 (MCO-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.INSPECT MAP LAMP ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT MAP LAMP ASSEMBLY
a.

Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Inspect the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK RADIO RECEIVER ASSEMBLY

NG

REPLACE MAP LIGHT ASSEMBLY

3.CHECK RADIO RECEIVER ASSEMBLY
a.
E316674C09
1.49,0.667 1.958,0.917 0.469,0.25 2.604,2.51 2.427,2.51 2.427,2.51 2.063,1.979 true 2.802,1.01 2.625,1.01 2.625,1.01 2.208,1.75 true 0.135,0.177 0.448,0.333 0.313,0.156 10 false *a 1.552,0.698 2,0.938 0.448,0.24 10 false G113 2.885,0.896 3.417,1.135 0.531,0.24 10 false MACC 2.667,2.375 3.198,2.615 0.531,0.24 10 false MIN-
*a Component with harness connected
(Radio Receiver Assembly)


Remove the radio receiver assembly with its connectors still connected.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G113-19 (MIN-) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G113-4 (MACC) - Body ground Ignition switch ACC 4 to 6 V



Result:
Proceed to
OK
NG



OK

4.CHECK MAP LIGHT ASSEMBLY

NG

REPLACE RADIO RECEIVER ASSEMBLY

4.CHECK MAP LIGHT ASSEMBLY
a.
E316675C03
0.26,0.729 0.708,0.969 0.448,0.24 0.615,1.729 0.813,1.729 0.813,1.729 1.438,1.219 true 2.604,1.917 2.354,1.917 2.354,1.917 1.594,1.208 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 0.385,0.75 0.698,0.948 0.313,0.198 10 false Q3 2.677,1.781 3.25,2 0.573,0.219 10 false MCO- 0.177,1.594 0.75,1.813 0.573,0.219 10 false MCO+
*a Component with harness connected
(Map Light Assembly)


Remove the map light assembly with its connectors still connected.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Turn the ignition switch to ACC.


c.

Connect an oscilloscope to terminals Q3-14 (MCO+) and Q3-13 (MCO-) of the map light assembly connector.


d.

Check the waveform of the telephone microphone assembly using the oscilloscope.


Result:
Result Proceed to
A waveform synchronized with the voice input to the map light assembly is output. A
A waveform synchronized with the voice input to the map light assembly is not output. B



A

REPLACE TELEPHONE MICROPHONE ASSEMBLY

B