Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)
RM33J0E _56 Audio / Visual / Telematics _038485 AUDIO / VIDEO _0193314 AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)  Radio Receiver Power Source Circuit  


DESCRIPTION

This circuit provides power to the radio receiver assembly.

WIRING DIAGRAM

E322195E04
3.042,1.458 4.875,1.656 1.833,0.198 10 false SFT LOCK-ACC 4.354,1.448 5.188,1.875 0.833,0.427 10 false ACC 5.813,1.573 6.646,2 0.833,0.427 10 false ACC1 5.802,0.667 6.635,1.094 0.833,0.427 10 false +B1 5.583,0.583 6.417,1.01 0.833,0.427 10 false 4 5.594,1.5 6.427,1.927 0.833,0.427 10 false 3 5.594,2.219 6.427,2.646 0.833,0.427 10 false 7 5.802,2.365 6.635,2.792 0.833,0.427 10 false GND1 5.417,3.073 7.031,3.396 1.615,0.323 10 false G114 5.417,3.219 7.031,3.542 1.615,0.323 10 false Radio Receiver Assembly 3.938,0.542 5.771,0.74 1.833,0.198 10 false RADIO 1.531,0.667 3.365,0.865 1.833,0.198 10 false from Battery 1.344,1.573 3.177,1.771 1.833,0.198 10 false from ACC Relay

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)
a.
E277492C50
1.427,0.25 1.885,0.51 0.458,0.26 2.281,0.969 2.521,0.594 2.521,0.594 2.771,0.594 true 2.031,0.958 2.313,0.26 2.313,0.26 2.563,0.26 true 0.948,1.854 1.135,1.854 1.135,1.854 1.552,1.427 true 2.813,0.479 3.177,0.729 0.365,0.25 10 false +B1 1.479,0.292 1.979,0.531 0.5,0.24 10 false G114 0.177,0.104 0.49,0.26 0.313,0.156 10 false *a 2.635,0.135 3.177,0.396 0.542,0.26 10 false ACC1 0.531,1.74 0.979,1.979 0.448,0.24 10 false GND1
*a Front view of wire harness connector
(to Radio Receiver Assembly)


Disconnect the radio receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G114-4 (+B1) - Body ground Always 11 to 14 V
G114-3 (ACC1) - Body ground Ignition switch ACC 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G114-7 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR