Home › Engine / Hybrid System › 2TR-FE ENGINE CONTROL › SFI SYSTEM
RM33J0E _51 Engine / Hybrid System _038454 2TR-FE ENGINE CONTROL _0193317 SFI SYSTEM C

2TR-FE ENGINE CONTROL  SFI SYSTEM  P0102  Mass Air Flow Circuit Low  P0103  Mass Air Flow Circuit High  


DESCRIPTION

The mass air flow meter sub-assembly is a sensor that measures the intake air volume using the following built-in components:

·

By-pass duct (allows some of the intake air to flow past a silicon chip sensor)

·

Silicon chip sensor (uses a heater control bridge circuit and temperature sensor bridge circuit to detect the difference in the temperature of the intake air that passes the sensors positioned before and after the heater).

·

Control circuit (converts the difference in temperature into a pulse signal and performs correction)


Intake air flows past the temperature sensor (before heater), the heater, and then the temperature sensor (after heater) of the silicon chip sensor in the by-pass duct. As the intake air is warmed up when it is exposed to the heater, the temperature of the intake air as it flows past the temperature sensor (after heater) is higher than when it flows past the temperature sensor (before heater). The difference in temperature of the intake air at each temperature sensor varies depending on the velocity of the intake air that flows past the silicon chip sensor. The temperature sensor bridge circuit detects the difference in temperature, and the control circuit converts it into a pulse signal and outputs it to the ECM. When the temperature detected by the temperature sensor (before heater) is higher than that detected by the temperature sensor (after heater), backflow of the intake air is detected.

The ECM calculates the intake air volume based on the pulse signal received from the mass air flow meter sub-assembly, and uses it to determine the fuel injection duration necessary for an optimal air-fuel ratio.

The heater control bridge circuit has a temperature sensor and power transistor, and maintains the heater temperature at a specific temperature.

HINT:

When DTCs are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM calculates the fuel injection duration based on the engine speed and throttle valve angle. Fail-safe mode continues until a pass condition is detected.


A332068C01
5.479,1.865 6.344,2.813 6.344,2.813 6.573,2.813 true 5.823,2.896 6.156,3.292 6.156,3.292 6.385,3.292 true 2.719,1.542 3.021,1.698 3.021,1.698 3.25,1.698 true 2.323,0.844 2.896,1.063 2.896,1.063 3.125,1.063 true 1.5,1.042 1.698,1.042 1.698,1.042 2.094,0.833 true 1.313,1.74 1.51,1.74 1.51,1.74 1.792,1.51 true 3.104,1.438 3.219,1.521 3.219,1.521 3.448,1.521 true 4.542,2.427 4.792,2.427 4.792,2.427 5.25,2.219 true 6.615,2.74 6.927,2.938 0.313,0.198 10 false *a 6.438,3.219 6.75,3.417 0.313,0.198 10 false *q 3.167,1 3.479,1.198 0.313,0.198 10 false *c 1.323,0.979 1.635,1.177 0.313,0.198 10 false *d 3.271,1.646 3.583,1.844 0.313,0.198 10 false *f 3.49,1.458 3.802,1.656 0.313,0.198 10 false *e 1.156,1.667 1.469,1.865 0.313,0.198 10 false *g 4.135,2.688 4.448,2.885 0.313,0.198 10 false 5V 4.135,3.344 4.448,3.542 0.313,0.198 10 false FG 4.135,4.313 4.604,4.552 0.469,0.24 10 false E2G 0.802,3.875 1.115,4.073 0.313,0.198 10 false *c 1.188,3.885 1.5,4.083 0.313,0.198 10 false *d 1.729,3.896 2.042,4.094 0.313,0.198 10 false *h 2.458,3.458 2.771,3.656 0.313,0.198 10 false *j 2.771,3.458 3.083,3.656 0.313,0.198 10 false *k 2.448,4.104 2.76,4.302 0.313,0.198 10 false *l 2.771,4.094 3.083,4.292 0.313,0.198 10 false *m 3.521,3.917 3.833,4.115 0.313,0.198 10 false *i 3.448,3.313 3.76,3.51 0.313,0.198 10 false *n 4.635,0.51 4.948,0.708 0.313,0.198 10 false *1 1.229,4.51 1.573,4.646 0.344,0.135 10 false *o 2.583,4.521 2.896,4.656 0.313,0.135 10 false *p 4.365,2.354 4.677,2.552 0.313,0.198 10 false *b
*1 Mass Air Flow Meter Sub-assembly - -
*a Silicon Chip Sensor *b By-pass Duct
*c Heater *d Heater Thermistor
*e Intake Air *f Temperature Sensor (After Heater)
*g Temperature Sensor (Before Heater) *h Intake Air Thermistor 1
*i Intake Air Thermistor 2 *j Temperature Sensor (Before Heater) 1
*k Temperature Sensor (After Heater) 2 *l Temperature Sensor (After Heater) 1
*m Temperature Sensor (Before Heater) 2 *n Control Circuit
*o Heater Control Bridge Circuit *p Temperature Sensor Bridge Circuit
*q Air Flow - -


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0102 Mass Air Flow Circuit Low The mass air flow meter sub-assembly output frequency is less than 0.1 kHz for 3 seconds
(1 trip detection logic)
·

Open or short in mass air flow meter sub-assembly circuit

·

Mass air flow meter sub-assembly

·

ECM


Comes on DTC stored
P0103 Mass Air Flow Circuit High The mass air flow meter sub-assembly output frequency is higher than 9.8 kHz for 3 seconds
(1 trip detection logic)
·

Open or short in mass air flow meter sub-assembly circuit

·

Mass air flow meter sub-assembly

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

If there is a defect or an open or short circuit in the mass air flow meter sub-assembly, the frequency level deviates from the normal operating range. The ECM interprets this deviation as a malfunction in the mass air flow meter sub-assembly circuit and stores a DTC.

Example:

When the sensor output frequency remains less than 0.1 kHz, or higher than 9.8 kHz for 3 seconds, the ECM stores a DTC.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Wait 5 seconds or more.

7.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P0102 or P0103.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A335967E07
0.292,3.271 2.563,3.5 2.271,0.229 10 false Mass Air Flow Meter Sub-assembly 5.615,3.219 6.073,3.417 0.458,0.198 10 false ECM 4.844,0.781 5.156,0.979 0.313,0.198 10 false C53 0.292,3.104 0.75,3.302 0.458,0.198 10 false A39 1.885,0.646 2.198,0.844 0.313,0.198 10 false 5V 1.896,1.229 2.208,1.427 0.313,0.198 10 false FG 1.823,1.823 2.281,2.021 0.458,0.198 10 false E2G 1.813,2.354 2.271,2.552 0.458,0.198 10 false THA 5.208,0.646 5.813,0.865 0.604,0.219 10 false VCVG 5.198,1.229 5.802,1.448 0.604,0.219 10 false VG 5.219,1.833 5.823,2.052 0.604,0.219 10 false E2G 5.219,2.375 5.823,2.594 0.604,0.219 10 false THA 2.219,0.646 2.375,0.844 0.156,0.198 10 false 3 2.229,1.24 2.385,1.438 0.156,0.198 10 false 1 2.25,1.823 2.406,2.021 0.156,0.198 10 false 2 2.26,2.365 2.417,2.563 0.156,0.198 10 false 4 4.875,0.604 5.188,0.802 0.313,0.198 10 false 33 4.875,1.177 5.188,1.375 0.313,0.198 10 false 24 4.885,1.771 5.198,1.969 0.313,0.198 10 false 32 4.875,2.323 5.188,2.521 0.313,0.198 10 false 23 6.115,0.344 6.375,0.594 0.26,0.25 10 false 5 V 4.844,1.354 5.156,1.552 0.313,0.198 10 false C53 4.833,1.938 5.146,2.135 0.313,0.198 10 false C53 4.833,2.5 5.146,2.698 0.313,0.198 10 false C53 6,1.052 6.26,1.302 0.26,0.25 10 false R

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF MASS AIR FLOW METER SUB-ASSEMBLY)
A332051C14
0.25,1.917 0.667,2.167 0.417,0.25 2.208,3.104 1.875,2.406 true 1.063,3.115 1.333,2.417 true 1.583,3.104 1.594,2.427 true 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 2.135,3.135 2.479,3.354 0.344,0.219 10 false 5V 0.333,1.969 0.792,2.167 0.458,0.198 10 false A39 0.99,3.135 1.333,3.354 0.344,0.219 10 false FG 1.49,3.146 1.833,3.365 0.344,0.219 10 false E2G
*a Front view of wire harness connector
(to Mass Air Flow Meter Sub-assembly)


a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A39-3 (5V) - Body ground Ignition switch ON 4.8 to 5.2 V
A39-1 (FG) - A39-2 (E2G) Ignition switch ON 4.8 to 5.2 V



Result:
Proceed to
OK
NG



OK

2.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

NG

4.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
2.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY
a.

Replace the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>MASS AIR FLOW METER>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

3.CHECK IF DTC OUTPUT RECURS (SEE IF DTC P0102 OR P0103 IS OUTPUT AGAIN)
3.CHECK IF DTC OUTPUT RECURS (SEE IF DTC P0102 OR P0103 IS OUTPUT AGAIN)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 234

d.

Turn the ignition switch off and wait for at least 30 seconds.


e.

Turn the ignition switch to ON and turn the GTS on.


f.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


h.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 234
Result:
Result Proceed to
DTC P0102 or P0103 is output A
DTCs are not output B




A

B

END

4.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C53-33 (VCVG) - A39-3 (5V) Always Below 1 Ω
C53-24 (VG) - A39-1 (FG) Always Below 1 Ω
C53-32 (E2G) - A39-2 (E2G) Always Below 1 Ω
C53-33 (VCVG) or A39-3 (5V) - Body ground Always 10 kΩ or higher
C53-24 (VG) or A39-1 (FG) - Body ground Always 10 kΩ or higher
C53-32 (E2G) or A39-2 (E2G) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR