Home › Vehicle Interior › SEAT › FRONT SEAT ASSEMBLY(for Manual Seat) › 2015.06–2016.07
RM33J0E _58 Vehicle Interior _038502 SEAT _0193318 FRONT SEAT ASSEMBLY(for Manual Seat) A

SEAT  FRONT SEAT ASSEMBLY(for Manual Seat)  REASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:
·
B394717

Wear protective gloves. Sharp areas on the parts may injure your hands.

·

There is risk of injury.

·

If the front seat side airbag was deployed, replace the front seat airbag assembly, separate type front seatback frame sub-assembly, separate type front seatback cover and separate type front seatback pad with the necessary parts in accordance with the extent of the collision damage.

·

Replace any other damaged parts as necessary.



HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedures listed below are for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 72201B 1.INSTALL SEAT TRACK HANDLE SUB-ASSEMBLY LH

a.

Attach the claw and install the seat track handle sub-assembly LH.

B413223


Hide 71052A 2.INSTALL FRONT SEAT CUSHION SPRING SUB-ASSEMBLY LH

a.
B413224C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


While rotating the part in installation direction (1) shown in the illustration, attach the hook.


b.

Push in Installation direction (2) shown in the illustration to attach the hook and install the front seat cushion spring sub-assembly LH.


Hide 71538A 3.INSTALL FRONT SEAT CUSHION EDGE PROTECTOR LH

a.
B416852C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Push in installation direction (1) shown in the illustration to install the guide.


b.

While expanding the part in installation direction (2) shown in the illustration, attach the claw.


c.

Install the front seat cushion edge protector LH with the screw.


Hide 71537G 4.INSTALL FRONT SEAT CUSHION EDGE PROTECTOR RH

HINT:

Use the same procedure as for the LH side.


Hide 71874 5.INSTALL FRONT SEAT LOWER CUSHION SHIELD LH (w/ Vertical Adjusting Handle LH)

a.
B421098C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Push in the installation direction (1) shown in the illustration.


b.

Push in the installation direction (2) shown in the illustration to attach the clip.


c.
B421099C01
0,0 0,0 false
V113147

Install in this Direction


Push in the guide in the installation direction shown in the illustration.


d.

Install the front seat lower cushion shield LH with the screw.


Hide 71873 6.INSTALL FRONT SEAT LOWER CUSHION SHIELD RH (w/ Vertical Adjusting Handle LH)

HINT:

Use the same procedure as for the LH side.


Hide 7.INSTALL SEAT COVER WIRE

a.
B403869N01
1.708,0.573 2.083,0.302 true 1.708,0.563 1.323,0.292 true 0.833,0.781 0.49,0.667 true 0.698,2.469 0.354,2.354 true 2.948,0.708 2.615,0.854 true 3.094,2.354 2.76,2.5 true 1.646,1.271 1.646,1.573 true 1.667,2.26 1.667,2.563 true 1.635,0.625 1.802,0.823 0.167,0.198 10 true A 1.583,1.604 1.75,1.802 0.167,0.198 10 true C 1.604,2.615 1.771,2.813 0.167,0.198 10 true D 3.031,0.594 3.198,0.792 0.167,0.198 10 true B 0.302,0.573 0.469,0.771 0.167,0.198 10 true B 0.115,2.25 0.281,2.448 0.167,0.198 10 true E 3.156,2.271 3.323,2.469 0.167,0.198 10 true E

Install the seat cover wire.

HINT:
·

There are service parts available for wires of 1000 mm or longer and formed wires.


·

When a wire that is less than 1000 mm (3.28 ft.) in length is needed, cut and shape a 1000 mm supplied wire into the dimensions shown in the illustration.


·

Refer to the precautions when creating a wire.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>PRECAUTION



Length:
A 170 mm (6.70 in.)
B 150 mm (5.91 in.)
C 230 mm (9.06 in.)
D 270 mm (10.63 in.)
E 290 mm (11.42 in.)


HINT:
B376752

The dimensions shown in the illustration are the length.



Hide 71071S 8.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER

HINT:
·

Refer to the precautions on wrinkles to avoid creating any on the separate type front seat cushion cover when installing the seat cover.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>PRECAUTION


·

As shown in the illustration, fix all of the cover seam allowances in the same direction.

B394024E01
2.5,0.24 3.271,0.438 0.771,0.198 10 false A - A 4.656,0.302 5.427,0.5 0.771,0.198 10 false B - B 0.198,0.396 0.354,0.594 0.156,0.198 10 false A 0.51,0.583 0.656,0.75 0.146,0.167 10 true A 0.938,0.802 1.094,1 0.156,0.198 10 false B 1.26,1.063 1.656,1.406 0.396,0.344 10 false B



a.

Temporarily install the separate type front seat cushion cover to the separate type front seat cushion pad.


b.

Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 18 new hog rings in the order shown in the illustration.

B409602C01
5.25,2.177 5.323,1.667 false 4.969,0.927 5.115,0.938 true 5.115,0.844 5.427,1.042 0.313,0.198 10 false *a 5.167,2.229 5.479,2.427 0.313,0.198 10 false *1 1.99,1.771 2.208,1.979 0.219,0.208 10 true (1) 2.615,1.781 2.833,1.99 0.219,0.208 10 true (2) 1.979,1.156 2.198,1.365 0.219,0.208 10 true (3) 2.594,1.156 2.813,1.365 0.219,0.208 10 true (4) 1.365,1.844 1.635,2.052 0.271,0.208 10 true (10) 1.417,1.354 1.688,1.563 0.271,0.208 10 true (11) 1.448,1.104 1.729,1.313 0.281,0.208 10 true (12) 1.448,0.792 1.729,1 0.281,0.208 10 true (13) 1.49,0.51 1.75,0.719 0.26,0.208 10 true (14) 3.146,1.844 3.365,2.052 0.219,0.208 10 true (5) 3.135,1.365 3.354,1.573 0.219,0.208 10 true (6) 3.135,1.125 3.354,1.333 0.219,0.208 10 true (7) 3.125,0.833 3.344,1.042 0.219,0.208 10 true (8) 3.104,0.563 3.323,0.771 0.219,0.208 10 true (9) 1.802,0.177 2.073,0.385 0.271,0.208 10 true (18) 2.125,0.177 2.385,0.385 0.26,0.208 10 true (17) 2.427,0.177 2.688,0.385 0.26,0.208 10 true (16) 2.75,0.177 3.021,0.417 0.271,0.24 10 true (15)
*1 Hog Ring Pliers - -
*a Cutout - -



c.

Using hog ring pliers, connect the 2 straps of the separate type front seat cushion cover to the separate type front seat cushion pad with 2 new hog rings.

HINT:
·

Do not dirty or damage the separate type front seatback cover.


·

Securely tighten the hog rings as shown in the illustration while making sure wrinkles do not form in the center of the fabric and separate type front seatback pad.



B413228C01
4.927,2.083 5.156,1.563 false 4.771,2.125 5.083,2.323 0.313,0.198 10 false *1
*1 Hog Ring Pliers - -



Hide 9.INSTALL SEAT CUSHION COVER WITH PAD

a.

While sliding the part in the direction indicated by the arrow shown in the illustration, align the J hook to attach the seat cushion cover with pad.

B413217


Hide 71587B 10.INSTALL FRONT SEATBACK EDGE PROTECTOR (for Low-back Seat Type)

a.
B409604

Attach the claw to Install the 2 front seatback edge protectors.


Hide 71054S 11.INSTALL FRONT SEATBACK SPRING SUB-ASSEMBLY LH (for Low-back Seat Type)

a.
B421100C01
1.875,1.323 2.677,0.927 true 0.448,1.292 1.406,1.406 true 2.74,0.833 3.052,1.031 0.313,0.198 10 false *1 0.198,1.208 0.51,1.406 0.313,0.198 10 false *1
*1 Front No. 2 Seatback Hook
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Temporarily install the 2 front No. 2 seatback hooks to the front seatback spring sub-assembly LH.


b.

Push in installation direction (1) shown in the illustration to install the front seatback spring sub-assembly LH.


c.

Push in installation direction (2) shown in the illustration to temporarily the front seatback spring sub-assembly LH.


d.
B403873

Attach the claw and install the 2 front seatback edge protectors.


Hide 71759D 12.INSTALL FRONT NO. 2 SEATBACK HOOK (for Low-back Seat Type)

a.
B413216C01
0,0 0,0 false
V113147

Install in this Direction


Push up installation direction shown in the illustration to attach the claw to install the 2 front No. 2 seatback hooks.


Hide 73920A 13.INSTALL FRONT SEAT AIRBAG ASSEMBLY LH (w/ Side Airbag System, for Low-back Seat Type)

Hide 73910A 14.INSTALL FRONT SEAT AIRBAG ASSEMBLY RH (w/ Side Airbag System, for Hi-back Seat Type)

Hide 15.INSTALL SEAT COVER WIRE

a.

Install the seat cover wire.

HINT:
·

There are service parts available for wires of 1000 mm or longer and formed wires.


·

When a wire that is less than 1000 mm (3.28 ft.) in length is needed, cut and shape a 1000 mm supplied wire into the dimensions shown in the illustration.


·

Refer to the precautions when creating a wire.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>PRECAUTION



i.
B402134N01
0.51,3.083 1.208,2.875 true 2.104,2.917 2.677,2.698 true 2.073,1.802 2.771,1.521 true 1.927,1.042 2.688,0.625 true 2.771,0.479 2.927,0.677 0.156,0.198 10 false A 2.844,1.396 3,1.594 0.156,0.198 10 false B 2.76,2.563 2.917,2.76 0.156,0.198 10 false C 0.323,2.99 0.479,3.188 0.156,0.198 10 false C

for Hi-back Seat Type:

Length:
A 150 mm (5.91 in.)
B 290 mm (11.42 in.)
C 420 mm (1.38 ft.)


HINT:
B376752

The dimensions shown in the illustration are the length.



ii.
B413333N01
1.969,1.365 2.917,1.115 true 2.333,2.969 2.885,3.021 true 2.313,3.198 2.896,3.021 true 2.99,1.021 3.146,1.219 0.156,0.198 10 true A 2.958,2.938 3.115,3.135 0.156,0.198 10 true B

for Low-back Seat Type, for Basic Style:

Length:
A 200 mm (7.87 in.)
B 420 mm (1.38 ft.)


HINT:
B376752

The dimensions shown in the illustration are the length.



iii.
B413213N01
2.365,1.094 3.031,0.896 true 0.792,0.49 1.375,0.802 true 1.76,1.333 1.885,1.021 true 2.313,3.208 2.854,2.958 true 2.323,3.031 2.844,2.958 true 0.625,0.396 0.781,0.594 0.156,0.198 10 false A 3.125,0.771 3.281,0.969 0.156,0.198 10 false A 1.833,0.844 1.99,1.042 0.156,0.198 10 true B 2.958,2.865 3.115,3.063 0.156,0.198 10 false C

for Low-back Seat Type, for High Style:

Length:
A 170 mm (6.70 in.)
B 200 mm (7.87 in.)
C 420 mm (1.38 ft.)


HINT:
B376752

The dimensions shown in the illustration are the length.




Hide 71073S 16.INSTALL SEPARATE TYPE FRONT SEATBACK COVER (for Hi-back Seat Type)

a.

Set the separate type front seatback cover.


b.

Using hog ring pliers, install the separate type front seatback cover with 8 new hog rings in the order shown in the illustration.

NOTICE:
·

Do not dirty or damage the separate type front seatback cover.


·

Securely tighten the hog rings as shown in the illustration while making sure wrinkles do not form in the center of the fabric and separate type front seatback pad.



HINT:

Install the hog rings at the cutouts if they are there.

B413335C01
5.125,0.948 4.979,0.927 true 3.448,0.729 2.833,0.885 true 2.5,0.875 2,0.719 true 2.229,1.115 1.729,0.958 true 3.688,1.021 3.073,1.177 true 3.365,1.979 2.76,1.417 true 3.365,1.969 3.031,1.458 true 1.604,1.552 2.25,1.333 true 1.625,1.542 2.458,1.375 true 5.25,2.125 5.354,1.656 true 5.156,2.146 5.469,2.344 0.313,0.198 10 false *1 5.115,0.844 5.427,1.042 0.313,0.198 10 false *a 1.781,0.583 2.031,0.802 0.25,0.219 10 false (1) 3.5,0.573 3.75,0.792 0.25,0.219 10 false (1) 3.75,0.896 4,1.115 0.25,0.219 10 false (2) 1.531,0.823 1.781,1.042 0.25,0.219 10 false (2) 1.385,1.448 1.635,1.667 0.25,0.219 10 false (3) 3.438,2 3.688,2.219 0.25,0.219 10 false (3)
*1 Hog Ring Pliers - -
*a Cutout - -




Hide 71073S 17.INSTALL SEPARATE TYPE FRONT SEATBACK COVER (for Low-back Seat Type)

HINT:
·

Refer to the precautions on wrinkles to avoid creating any on the separate type front seatback cover when installing the seat cover.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>PRECAUTION


·

As shown in the illustration, fix all of the cover seam allowances in the same direction.

B394023N01
0.542,0.354 0.698,0.552 0.156,0.198 10 false A 0.813,0.458 0.969,0.656 0.156,0.198 10 false A 1.177,0.583 1.333,0.781 0.156,0.198 10 false B 1.5,0.719 1.656,0.917 0.156,0.198 10 true B 1.125,0.052 1.281,0.25 0.156,0.198 10 false C 0.813,0.24 0.969,0.438 0.156,0.198 10 true C 2.042,0.229 2.813,0.427 0.771,0.198 10 false A - A 3.438,0.24 4.208,0.438 0.771,0.198 10 false C - C 5.615,0.281 6.385,0.479 0.771,0.198 10 false B - B



a.

Set the separate type front seatback cover.


b.

for Basic Style:

i.

Using hog ring pliers, install the separate type front seatback cover with 6 new hog rings in the order shown in the illustration.

NOTICE:
·

Do not dirty or damage the separate type front seatback cover.


·

Securely tighten the hog rings as shown in the illustration while making sure wrinkles do not form in the center of the fabric and separate type front seatback pad.



HINT:

Install the hog rings at the cutouts if they are there.

B409606C01
5.25,2.229 5.24,1.646 true 5.094,0.948 4.958,0.938 true 3.417,0.427 3.063,0.719 true 1.74,0.302 2,0.563 true 1.563,0.802 1.979,1.188 true 1.563,0.792 2.271,1.156 true 2.75,1.219 3.365,1.146 true 2.927,1.375 3.365,1.156 true 5.115,0.854 5.427,1.052 0.313,0.198 10 false *a 5.198,2.281 5.51,2.479 0.313,0.198 10 false *1 3.417,0.229 3.875,0.427 0.458,0.198 10 false (1) 1.563,0.135 2.021,0.333 0.458,0.198 10 false (1) 1.365,0.677 1.823,0.875 0.458,0.198 10 false (2) 3.417,1.052 3.875,1.25 0.458,0.198 10 false (2)
*1 Hog Ring Pliers - -
*a Cutout - -





c.

for High Style:

i.

Using hog ring pliers, install the separate type front seatback cover with 12 new hog rings in the order shown in the illustration.

NOTICE:
·

Do not dirty or damage the separate type front seatback cover.


·

Securely tighten the hog rings as shown in the illustration while making sure wrinkles do not form in the center of the fabric and separate type front seatback pad.



HINT:

Install the hog rings at the cutouts if they are there.

B413336C01
5.375,2.24 5.344,1.667 true 5.094,0.917 4.969,0.938 true 3.604,1.052 2.958,1.146 true 3.615,1.073 3.063,0.74 true 1.979,0.604 1.333,0.698 true 2,1.031 1.344,0.698 true 2.333,1.156 2.677,0.26 true 2.646,1.25 2.667,0.271 true 3.531,2.292 2.729,2.438 true 3.531,2.292 2.781,2.188 true 3.542,2.313 2.896,1.521 true 1,1.75 1.938,1.333 true 0.979,1.75 1.792,1.927 true 1.021,1.76 1.74,2.26 true 5.313,2.292 5.625,2.49 0.313,0.198 10 false *1 5.104,0.833 5.417,1.031 0.313,0.198 10 false *a 3.698,1.021 4.156,1.219 0.458,0.198 10 false (1) 1.115,0.615 1.573,0.813 0.458,0.198 10 false (1) 2.604,0.073 3.063,0.271 0.458,0.198 10 false (2) 0.76,1.656 1.219,1.854 0.458,0.198 10 false (3) 3.646,2.25 4.104,2.448 0.458,0.198 10 false (3)
*1 Hog Ring Pliers - -
*a Cutout - -





Hide 18.INSTALL SEATBACK COVER WITH PAD

a.

for Hi-back Seat Type:

i.
B402131C01
0,0 0,0 false
V113147

Install in this Direction


Push in installation direction shown in the illustration to temporarily install the seatback cover with pad.



b.

for Low-back Seat Type:

i.
B415862C01
0,0 0,0 false
V113147

Install in this Direction


Push in installation direction shown in the illustration to temporarily install the seatback cover with pad.



c.

w/ Side Airbag System:

i.
B413233C01
1.813,2.979 2.625,2.688 true 0.479,1.667 1.469,1.76 true 0.292,1.594 0.604,1.792 0.313,0.198 10 false *1 2.677,2.563 2.99,2.76 0.313,0.198 10 false *2
*1 J Hook A
*2 J Hook B
V113147

Install in this Direction


Push in the installation direction shown in the illustration to attach the J hook A and J hook B.

HINT:

For RH seats, push up from below.



ii.
B413563C01
2.021,1.333 2.49,0.677 true 0.958,3.135 1.26,2.896 true 0.729,3.073 1.042,3.271 0.313,0.198 10 false *1 2.479,0.51 2.792,0.708 0.313,0.198 10 false *2
*1 J Hook B (J Hook A and J Hook B)
*2 J Hook C
V113147

Install in this Direction


Push in the installation direction shown in the illustration to attach the J hook B (J hook A and J hook B) and J hook C.

HINT:

For RH seats, push up from below.



iii.

Install the new rivet to J hook B.

B413208C01
2.219,1.656 3.104,1.177 true 0.74,1.75 1.854,1.729 true 5.542,1.771 6.625,1.656 true 4.229,1.135 5.208,1.583 true 0.094,0.094 0.406,0.292 0.313,0.198 10 false *A 3.604,0.146 3.917,0.344 0.313,0.198 10 false *B 0.542,1.677 0.854,1.875 0.313,0.198 10 false *1 6.688,1.542 7,1.74 0.313,0.198 10 false *1 3.167,1.063 3.479,1.26 0.313,0.198 10 false *2 4.021,1.063 4.333,1.26 0.313,0.198 10 false *2
*A for LH seat *B for RH seat
*1 J Hook A *2 J Hook B


HINT:
·

For LH seats, install the top rivet.


·

For RH seats, install the bottom rivet.




iv.

Place your hand at the position shown in the illustration and push in the install direction to attach the J hook B.

B413236C01
2.354,1.417 2.771,1 true 1.25,2.208 1.99,1.635 true 1.615,0.917 1.417,0.646 true 1.281,0.49 1.594,0.688 0.313,0.198 10 false *3 2.813,0.875 3.125,1.073 0.313,0.198 10 false *2 1.031,2.177 1.344,2.375 0.313,0.198 10 false *1
*1 J Hook A *2 J Hook B
*3 J Hook C - -
V113146

Place Hand Here
V113147

Install in this Direction




d.

for Hi-back Seat Type:

i.

Using hog ring pliers, install the 2 new hog rings.

B413237C01
5.26,2.271 5.323,1.646 true 5.104,0.958 4.958,0.938 true 5.177,2.323 5.49,2.521 0.313,0.198 10 false *1 5.115,0.844 5.427,1.042 0.313,0.198 10 false *a
*1 Hog Ring Pliers - -
*a Cutout - -



ii.

Using hog ring pliers, install the 5 new hog rings.

B413238C01
5.271,2.198 5.354,1.667 false 4.969,0.917 5.115,0.927 true 5.125,0.833 5.438,1.031 0.313,0.198 10 false *a 5.219,2.26 5.531,2.458 0.313,0.198 10 false *1
*1 Hog Ring Pliers - -
*a Cutout - -




Hide 71931 19.INSTALL FRONT SEAT HEADREST SUPPORT (for Low-back Seat Type)

a.
B403861C01
0,0 0,0 false
V113147

Install in this Direction


Push in the installation direction shown in the illustration to attach the claw and install the 2 front seat headrest supports.


b.
B413205C01
0,0 0,0 false
V113147

Install in this Direction


Pull in the installation direction shown in the illustration to attach the guide to the 2 straps.


c.
B413232C01
0,0 0,0 false
V113147

Install in this Direction


Close the fasteners as shown in the illustration.


d.

Using hog ring pliers, install 5 new hog rings.

B409607C01
5.094,0.948 4.938,0.938 true 5.51,1.698 5.354,1.656 true 5.438,1.688 5.281,1.646 true 5.5,2.292 5.333,1.646 true 5.094,0.865 5.406,1.063 0.313,0.198 10 false *a 5.458,2.375 5.771,2.573 0.313,0.198 10 false *1
*1 Hog Ring Pliers - -
*a Cutout - -



Hide 71759C 20.INSTALL FRONT NO. 1 SEATBACK HOOK (w/ Front No. 1 Seatback Hook)

a.
B416134

Attach the claw and install the front No. 1 seatback hook.


Hide 71876F 21.INSTALL RECLINING ADJUSTER INSIDE COVER LH

a.
B413242C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Push down in installation direction (1) shown in the illustration.


b.

Rotate the part in installation direction (2) shown in the illustration and align the guide to install the reclining adjuster inside cover LH.


Hide 71875E 22.INSTALL RECLINING ADJUSTER INSIDE COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 71013S 23.INSTALL FRONT SEATBACK FRAME SUB-ASSEMBLY RH (for Hi-back Seat Type)

a.
B403855C01
0.083,0.094 0.302,0.292 0.219,0.198 10 true *A 0.146,2.563 0.365,2.76 0.219,0.198 10 true *B
*A LH Side
*B RH Side


Install the 4 bolts and front seatback frame sub-assembly RH.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


b.
B416892C01
1.063,4.396 2.552,3.677 true 1.323,1.49 2.323,1.927 true 0.052,0.063 0.292,0.26 0.24,0.198 10 true *A 0.073,2.438 0.313,2.635 0.24,0.198 10 true *B 2.396,1.844 2.708,2.042 0.313,0.198 10 false *1 0.844,4.323 1.156,4.521 0.313,0.198 10 false *1
*A LH Side
*B RH Side
*1 Separate Type Front Seat Cushion Cover


Attach the hook.


c.
B403868C01
0.958,3.052 0.729,2.26 true 2.188,2.917 1.063,1.979 true 1.917,1.385 1.448,0.479 true 2.74,0.917 2.625,0.542 true 1.25,0.302 1.448,0.5 0.198,0.198 10 true *1 2.479,0.323 2.677,0.521 0.198,0.198 10 true *1 2.229,2.938 2.427,3.135 0.198,0.198 10 true *1 0.927,3.104 1.125,3.302 0.198,0.198 10 true *2
*1 Wire Harness Clamp
*2 Connector Clamp


w/ Side Airbag System:

i.

Attach the wire harness clamp and connector clamp.



d.
B403856

Install the band in the position shown in the illustration.


Hide 71014S 24.INSTALL FRONT SEATBACK FRAME SUB-ASSEMBLY LH (for Low-back Seat Type)

a.
B413201C01
0.094,0.094 0.406,0.292 0.313,0.198 10 false *A 0.156,2.25 0.469,2.448 0.313,0.198 10 false *B
*A RH Side
*B LH Side


Install the 4 bolts and front seatback frame sub-assembly LH.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


b.
B416712C01
1.208,2.052 2.208,1.583 true 0.875,3.792 2.323,4.469 true 0.083,0.083 0.396,0.281 0.313,0.198 10 false *A 0.094,2.219 0.406,2.417 0.313,0.198 10 false *B 0.99,1.969 1.302,2.167 0.313,0.198 10 false *1 2.417,4.365 2.729,4.563 0.313,0.198 10 false *1
*A RH Side
*B LH Side
*1 Separate Type Front Seat Cushion Cover


Attach the hook.


c.
B413199C01
0.76,0.896 0.99,0.417 true 1.521,1.385 1.75,0.76 true 2.438,1.813 2.51,1.281 true 2.781,2.135 3.156,1.75 true 2.417,1.094 2.615,1.292 0.198,0.198 10 true *1 1.698,0.563 1.896,0.76 0.198,0.198 10 true *1 0.948,0.24 1.146,0.438 0.198,0.198 10 true *1 3.125,1.594 3.323,1.792 0.198,0.198 10 true *2
*1 Wire Harness Clamp
*2 Connector Clamp


w/ Side Airbag System:

i.

Attach the wire harness clamp and connector clamp.



d.
B413198

Install the band in the position shown in the illustration.


Hide 73240 25.INSTALL FRONT SEAT INNER BELT ASSEMBLY LH

Hide 71862 26.INSTALL FRONT SEAT INNER CUSHION SHIELD LH

a.
B413247C01
0,0 0,0 false
V113147

Install in this Direction


Push in the installation direction shown in the illustration to attach the claw and guide.


b.
B413248C01
0,0 0,0 false
V113147

Install in this Direction


Push in the installation direction shown in the illustration and attach the claw to install the front seat inner cushion shield LH.


Hide 71812D 27.INSTALL FRONT SEAT CUSHION SHIELD LH

a.
B413249C01
0,0 0,0 false
V113147

Install in this Direction


w/ Vertical Adjusting Handle LH:

i.

Push in the installation direction shown in the illustration and attach the claw and clip.


ii.
B413250C01
0,0 0,0 false
V113147

Install in this Direction


Push in the installation direction shown in the illustration and attach the clip, claw and guide to install the front seat cushion shield LH.



b.
B413251C01
0,0 0,0 false
V113147

Install in this Direction


w/o Vertical Adjusting Handle LH:

i.

Push in the installation direction shown in the illustration and attach the claw and clip.


ii.
B413252C01
0,0 0,0 false
V113147

Install in this Direction


Push in the installation direction shown in the illustration and attach the claw and guide.


iii.

Install the screw.



c.
B413253C01
0,0 0,0 false
V113147

Install in this Direction


Push in the installation direction shown in the illustration and attach the claw to install the front seat cushion shield LH.


Hide 72495 28.INSTALL VERTICAL ADJUSTING HANDLE LH (w/ Vertical Adjusting Handle LH)

a.
B413254C01
0,0 0,0 false
V113147

Install in this Direction


Attach the guide, and then push in the install direction shown in the illustration to install the vertical adjusting handle LH.


b.
B413255

Install the screw.


Hide 72526E 29.INSTALL RECLINING ADJUSTER RELEASE HANDLE LH

a.
B413256C01
0,0 0,0 false
V113147

Install in this Direction


w/ Vertical adjusting Handle LH:

i.

With the reclining adjuster release handle LH pulled up.


ii.

Push in the installation direction shown in the illustration and attach the claw to install the reclining adjuster release handle LH.



b.
B413257C01
0,0 0,0 false
V113147

Install in this Direction


w/o Vertical adjusting Handle LH:

i.

Push in the installation direction shown in the illustration and attach the claw to install the reclining adjuster release handle LH.



Hide 71849 30.INSTALL SEAT ADJUSTER COVER CAP LH

a.
B413258C01
0,0 0,0 false
V113147

Install in this Direction


Push in the installation direction shown in the illustration to install the 2 seat adjuster cover caps LH.


Hide 71910A 31.INSTALL FRONT SEAT HEADREST ASSEMBLY (for Low-back Seat Type)

a.

Install the front seat headrest assembly.