Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING(for Double Cab)
RM33J0E _58 Vehicle Interior _038506 INTERIOR PANELS / TRIM _0193463 ROOF HEADLINING(for Double Cab) A

INTERIOR PANELS / TRIM  ROOF HEADLINING(for Double Cab)  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



CAUTION:
B414214

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 4.REMOVE FRONT SEAT ASSEMBLY RH

Hide 5.REMOVE REAR SEAT ASSEMBLY

Hide 58810J 6.REMOVE CONSOLE BOX ASSEMBLY (w/ Console Box Lid)

Hide 58901A 7.REMOVE REAR CONSOLE BOX SUB-ASSEMBLY (w/ Rear Console Box)

Hide 58811A 8.REMOVE FRONT CONSOLE BOX (w/o Console Box Lid)

Hide 74610A 9.REMOVE ASSIST GRIP SUB-ASSEMBLY (w/ Assist Grip)

Hide 62212 10.REMOVE FRONT PILLAR GARNISH LH

Hide 62211 11.REMOVE FRONT PILLAR GARNISH RH

Hide 67914B 12.REMOVE FRONT DOOR SCUFF PLATE LH

a.
B404552C01
0.521,0.354 0.698,0.219 true 0.688,0.083 0.875,0.24 0.188,0.156 10 true *a
*a Protective Tape


Put protective tape around the front door scuff plate LH.


b.
B404553C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction


Place your hands at the position shown in the illustration and pull as shown to detach the claw and remove the front door scuff plate LH.


Hide 67913B 13.REMOVE FRONT DOOR SCUFF PLATE RH

a.
B404555C01
2.927,0.469 2.656,0.219 true 2.521,0.073 2.708,0.229 0.188,0.156 10 true *a
*a Protective Tape


Put protective tape around the front door scuff plate RH.


b.
B404556C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction


Place your hands at the position shown in the illustration and pull as shown to detach the claw and remove the front door scuff plate RH.


Hide 67918E 14.REMOVE REAR DOOR SCUFF PLATE LH

a.
B404558C02
3.063,1.385 3.115,0.844 true 2.99,0.698 3.198,0.854 0.208,0.156 10 true *a
*a Protective Tape


Put protective tape around the rear door scuff plate LH.


b.
B404559C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction


Place your hands at the position shown in the illustration and pull as shown to detach the claw and remove the rear door scuff plate LH.


Hide 67917C 15.REMOVE REAR DOOR SCUFF PLATE RH

a.
B404561C01
0.542,1.365 0.354,0.99 true 0.219,0.823 0.448,0.979 0.229,0.156 10 true *a
*a Protective Tape


Put protective tape around the rear door scuff plate RH.


b.
B404562C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction


Place your hands at the position shown in the illustration and pull as shown to detach the claw and remove the rear door scuff plate RH.


Hide 62414A 16.REMOVE LOWER CENTER PILLAR GARNISH LH

a.
B404564

Remove the bolt and disconnect the front seat outer belt assembly LH.


b.
B404565C01
3.083,1.5 3.323,1.667 0.24,0.167 10 false *1 0.354,1.51 0.667,1.667 0.313,0.156 10 false *2
*1 Front Door Opening Trim Weatherstrip LH
*2 Rear Door Opening Trim Weatherstrip LH


Disconnect the front door opening trim weatherstrip LH and rear door opening trim weatherstrip LH in the range shown in the illustration.


c.
B404566C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction


Place your hands at the position shown in the illustration and pull as shown to detach the claw and clip and remove the lower center pillar garnish LH.


Hide 62413A 17.REMOVE LOWER CENTER PILLAR GARNISH RH

a.
B404568

Remove the bolt and disconnect the front seat outer belt assembly RH.


b.
B404569C01
0.208,1.521 0.521,1.677 0.313,0.156 10 false *1 2.927,1.51 3.24,1.667 0.313,0.156 10 false *2
*1 Front Door Opening Trim Weatherstrip RH
*2 Rear Door Opening Trim Weatherstrip RH


Disconnect the front door opening trim weatherstrip RH and rear door opening trim weatherstrip RH in the range shown in the illustration.


c.
B404570C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction


Place your hands at the position shown in the illustration and pull as shown to detach the claw and clip and remove the lower center pillar garnish RH.


Hide 74617F 18.REMOVE ASSIST GRIP PLUG LH

HINT:

Use the same procedure for both assist grip plugs.


a.
B404649C01
2.146,1 2.531,0.927 true 2.521,0.802 2.75,0.958 0.229,0.156 10 true *a
*a Protective Tape


Put protective tape around the assist grip plug LH.


b.
B404650C01
2.49,1.385 2.271,1.052 true 2.458,1.365 2.667,1.521 0.208,0.156 10 true *a
*a Protective Tape
V113146

Insert Thin-bladed Screwdriver Here
V113147

Remove in this Direction


Insert a thin-bladed screwdriver at the position shown in the illustration and detach the claw and remove the assist grip plug LH.

HINT:

Tape the thin-bladed screwdriver tip before use.



Hide 74617A 19.REMOVE ASSIST GRIP PLUG RH

HINT:

Use the same procedure for both assist grip plugs.


a.
B405816C01
0.833,1 1.292,1.083 true 0.594,0.875 0.844,1.042 0.25,0.167 10 true *a
*a Protective Tape


Put protective tape around the assist grip plug RH.


b.
B405817C01
0.99,1.469 1.146,1.052 true 0.885,1.458 1.115,1.615 0.229,0.156 10 true *a
*a Protective Tape
V113146

Insert Thin-bladed Screwdriver Here
V113147

Remove in this Direction


Insert a thin-bladed screwdriver at the position shown in the illustration and detach the claw and remove the assist grip plug RH.

HINT:

Tape the thin-bladed screwdriver tip before use.



Hide 74680 20.REMOVE PILLAR ASSIST GRIP ASSEMBLY

HINT:

Use the same procedure for both pillar assist grip assemblies.


a.
B404655

Remove the 2 bolts and pillar assist grip assembly.


Hide 73178A 21.REMOVE SEAT BELT ANCHOR COVER CAP

HINT:

Use the same procedure for both seat belt anchor cover caps.


a.
B404572C01
0.458,0.75 1.313,0.885 true 0.281,0.625 0.594,0.781 0.313,0.156 10 false *a
*a Protective Tape


Put protective tape around the seat belt anchor cover cap.


b.
B404573C01
0.969,1.229 1.198,0.813 true 0.833,1.219 1.042,1.375 0.208,0.156 10 true *a
*a Protective Tape
V113146

Insert Thin-bladed Screwdriver Here
V113147

Remove in this Direction


Insert a thin-bladed screwdriver at the position shown in the illustration and detach the claw and remove the seat belt anchor cover cap.

HINT:

Tape the thin-bladed screwdriver tip before use.



Hide 62412B 22.REMOVE UPPER CENTER PILLAR GARNISH LH

a.
B404578

Remove the bolt and disconnect the front seat outer belt assembly LH.


b.
B404580C01
2.729,1.688 3.042,1.844 0.313,0.156 10 false *1 0.229,1.708 0.542,1.865 0.313,0.156 10 false *2
*1 Front Door Opening Trim Weatherstrip LH
*2 Rear Door Opening Trim Weatherstrip LH


Disconnect the front door opening trim weatherstrip LH and rear door opening trim weatherstrip LH in the range shown in the illustration.


c.
B404579C01
0,0 0,0 false
V113146

Insert Clip Remover Here
V113147

Remove in this Direction


Insert a clip remover at the position shown in the illustration and pull as shown to detach the clip and remove the upper center pillar garnish LH.


Hide 62411B 23.REMOVE UPPER CENTER PILLAR GARNISH RH

a.
B404582

Remove the bolt and disconnect the front seat outer belt assembly RH.


b.
B404584C01
0.49,1.698 0.802,1.854 0.313,0.156 10 false *1 2.979,1.698 3.208,1.854 0.229,0.156 10 false *2
*1 Front Door Opening Trim Weatherstrip RH
*2 Rear Door Opening Trim Weatherstrip RH


Disconnect the front door opening trim weatherstrip RH and rear door opening trim weatherstrip RH in the range shown in the illustration.


c.
B404583C01
0,0 0,0 false
V113146

Insert Clip Remover Here
V113147

Remove in this Direction


Insert a clip remover at the position shown in the illustration and pull as shown to detach the clip and remove the upper center pillar garnish RH.


Hide 73709 25.REMOVE TETHER ANCHOR BRACKET SUB-ASSEMBLY

HINT:

Use the same procedure for both tether anchor bracket sub-assemblies.


a.
B404593

Remove the bolt and tether anchor bracket sub-assembly.


Hide 64261C 26.REMOVE UPPER BACK PANEL GARNISH

a.
B404589C01
1.083,1.917 1.198,1.635 true 0.948,1.906 1.146,2.094 0.198,0.188 10 true *a
*a Protective Tape


Put protective tape around the back panel trim cover.


b.
B404590C01
0.427,1.354 0.833,1.542 true 0.208,1.229 0.438,1.385 0.229,0.156 10 true *a
*a Protective Tape
V113146

Insert Thin-bladed Screwdriver Here
V113147

Remove in this Direction


Insert a thin-bladed screwdriver at the position shown in the illustration and detach the claw and remove the back panel trim cover.

HINT:

Tape the thin-bladed screwdriver tip before use.



c.
B404586C01
2.563,1.833 2.365,1.573 true 2.51,1.802 2.74,1.958 0.229,0.156 10 true *a
*a Protective Tape


Put protective tape around the belt guide.


d.
B404587C01
1.031,1.625 1.292,1.708 true 1.271,1.615 1.49,1.802 0.219,0.188 10 true *a
*a Protective Tape
V113146

Insert Thin-bladed Screwdriver Here
V113147

Remove in this Direction


Insert a thin-bladed screwdriver at the position shown in the illustration and detach the claw and disconnect the belt guide.

HINT:

Tape the thin-bladed screwdriver tip before use.



e.
B404596C01
0.313,0.688 0.188,1.104 true 0.208,0.563 0.448,0.719 0.24,0.156 10 true *a
*a Protective Tape


Put protective tape around the upper back panel garnish.


f.
B404597C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction


Place your hands at the position shown in the illustration and pull as shown to detach the claw and clip and remove the upper back panel garnish.


Hide 62514A 27.REMOVE LOWER QUARTER TRIM PANEL LH

a.
B404599C01
2.521,1.052 2.833,1.208 0.313,0.156 10 false *1
*1 Rear Door Opening Trim Weatherstrip LH


Disconnect the rear door opening trim weatherstrip LH in the range shown in the illustration.


b.
B404600C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction


Place your hands at the position shown in the illustration and pull as shown to detach the claw and clip and remove the lower quarter trim panel LH.


Hide 62513A 28.REMOVE LOWER QUARTER TRIM PANEL RH

a.
B404602C01
0.76,1.031 1.073,1.188 0.313,0.156 10 false *1
*1 Rear Door Opening Trim Weatherstrip RH


Disconnect the rear door opening trim weatherstrip RH in the range shown in the illustration.


b.
B404603C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction


Place your hands at the position shown in the illustration and pull as shown to detach the claw and clip and remove the lower quarter trim panel RH.


Hide 73178B 29.REMOVE SEAT BELT ANCHOR COVER CAP

HINT:

Use the same procedure for both seat belt anchor cover caps.


a.
B404605C01
2.115,0.792 2.646,0.906 true 2.615,0.844 2.844,1 0.229,0.156 10 true *a
*a Protective Tape


Put protective tape around the seat belt anchor cover cap.


b.
B404606C01
2.406,1.063 2.25,0.771 true 2.354,1.042 2.573,1.198 0.219,0.156 10 true *a
*a Protective Tape
V113146

Insert Thin-bladed Screwdriver Here
V113147

Remove in this Direction


Insert a thin-bladed screwdriver at the position shown in the illustration and detach the claw and remove the seat belt anchor cover cap.

HINT:

Tape the thin-bladed screwdriver tip before use.



Hide 62512 30.REMOVE QUARTER INSIDE TRIM BOARD LH

a.
B404611

Remove the bolt and disconnect the rear seat outer belt assembly LH.


b.
B404612C01
2.563,1.063 2.875,1.219 0.313,0.156 10 false *1
*1 Rear Door Opening Trim Weatherstrip LH


Disconnect the rear door opening trim weatherstrip LH in the range shown in the illustration.


c.
B404613C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction


Place your hands at the position shown in the illustration and pull as shown to detach the clip and remove the quarter inside trim board LH.


Hide 62511 31.REMOVE QUARTER INSIDE TRIM BOARD RH

a.
B404615

Remove the bolt and disconnect the rear seat outer belt assembly RH.


b.
B404616C01
0.458,1.042 0.771,1.198 0.313,0.156 10 false *1
*1 Rear Door Opening Trim Weatherstrip RH


Disconnect the rear door opening trim weatherstrip RH in the range shown in the illustration.


c.
B404617C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction


Place your hands at the position shown in the illustration and pull as shown to detach the clip and remove the quarter inside trim board RH.


Hide 87810 32.REMOVE INNER REAR VIEW MIRROR ASSEMBLY

Hide 81260A 33.REMOVE MAP LIGHT ASSEMBLY

Hide 81240 34.REMOVE NO. 1 ROOM LIGHT ASSEMBLY

Hide 74325 35.REMOVE VISOR BRACKET COVER LH

a.

Open the visor assembly LH.


b.
B404635C01
0.667,1.427 1.198,1.677 true 0.458,1.292 0.688,1.448 0.229,0.156 10 true *a
*a Protective Tape
V113146

Insert Thin-bladed Screwdriver Here


Insert a thin-bladed screwdriver at the position shown in the illustration and detach the claw and remove the visor bracket cover LH.

HINT:

Tape the thin-bladed screwdriver tip before use.



Hide 74325 36.REMOVE VISOR BRACKET COVER RH

a.

Open the visor assembly RH.


b.
B404636C01
2.188,1.625 2.792,1.365 true 2.802,1.229 3.031,1.385 0.229,0.156 10 true *a
*a Protective Tape
V113146

Insert Thin-bladed Screwdriver Here


Insert a thin-bladed screwdriver at the position shown in the illustration and detach the claw and remove the visor bracket cover RH.

HINT:

Tape the thin-bladed screwdriver tip before use.



Hide 74320 37.REMOVE VISOR ASSEMBLY LH

a.
B404637

Remove the 2 screws.


b.
B404639C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Pull in the direction (1) shown in the illustration to disconnect the visor assembly LH from the visor holder.


c.

Pull in the direction (2) shown in the illustration to remove the visor assembly LH.


Hide 74310 38.REMOVE VISOR ASSEMBLY RH

a.
B404638

Remove the 2 screws.


b.
B404640C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Pull in the direction (1) shown in the illustration to disconnect the visor assembly RH from the visor holder.


c.

Pull in the direction (2) shown in the illustration to remove the visor assembly RH.


Hide 74348 39.REMOVE VISOR HOLDER

HINT:

Use the same procedure for both visor holders.


a.
B404621C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Turn the visor holder clockwise approximately 45° and pull it out as shown in the illustration.


b.

Detach the claw and remove the visor holder.


Hide 74610A 40.REMOVE ASSIST GRIP SUB-ASSEMBLY

HINT:

Use the same procedure for all assist grip sub-assemblies.


a.
B404479C01
1.042,1.167 1.74,1.281 true 1.771,1.229 1.99,1.385 0.219,0.156 10 true *a
*a Protective Tape


Put protective tape around the assist grip sub-assembly.


b.
B404480C01
0.875,0.76 0.427,0.406 true 0.198,0.271 0.427,0.427 0.229,0.156 10 true *a
*a Protective Tape
V113146

Insert Thin-bladed Screwdriver Here
V113147

Remove in this Direction


Insert a thin-bladed screwdriver at the position shown in the illustration and detach the claw and open the assist grip cover.

HINT:

Tape the thin-bladed screwdriver tip before use.



c.
B404483

Remove the 2 bolts and assist grip sub-assembly.


Hide 74605A 41.REMOVE COAT HOOK SUB-ASSEMBLY

HINT:

Use the same procedure for both coat hook sub-sub-assemblies.


a.
B410865C01
1.75,3.26 2.469,3.01 true 2.479,2.906 2.698,3.063 0.219,0.156 10 true *a
*a Protective Tape


Using a thin-bladed screwdriver, push on the area shown in the illustration.

HINT:

Tape the thin-bladed screwdriver tip before use.



b.
B404619C01
2.427,0.479 2.729,0.677 0.302,0.198 10 true 90°
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Turn the coat hook sub-assembly clockwise approximately 90° and pull it out as shown in the illustration to remove it.


Hide 63339A 42.REMOVE ROOF HEADLINING SERVICE HOLE COVER (w/o Assist Grip)

a.
B410866

Using a clip remover, remove the 2 roof headlining service hole covers.


Hide 63310 43.REMOVE ROOF HEADLINING ASSEMBLY

a.
B404484

Disconnect the connector and detach the clamp from the front pillar LH.


b.

Disconnect the front door opening trim weatherstrip LH and rear door opening trim weatherstrip LH in the range shown in the illustration.

B404629C01
5.125,1.344 5.438,1.5 0.313,0.156 10 false *1 2.479,1.323 2.792,1.479 0.313,0.156 10 false *2
*1 Front Door Opening Trim Weatherstrip LH *2 Rear Door Opening Trim Weatherstrip LH



c.

Disconnect the front door opening trim weatherstrip RH and rear door opening trim weatherstrip RH in the range shown in the illustration.

B404630C01
2.01,1.344 2.323,1.5 0.313,0.156 10 false *1 4.583,1.344 4.896,1.5 0.313,0.156 10 false *2
*1 Front Door Opening Trim Weatherstrip RH *2 Rear Door Opening Trim Weatherstrip RH



d.
B404632

Using a clip remover, remove the clip.


e.
B414352C01
0,0 0,0 false
V113147

Remove in this Direction


Turn the roof headlining assembly diagonally and bend slightly to remove it from the front door.

NOTICE:
·

Make sure wrinkles do not form in the roof headlining assembly during removal.

·

Make sure that the roof headlining assembly does not get caught on anything as it may become bent or damaged.

·

Do not damage the roof headlining assembly or vehicle interior.




Hide 66423 44.REMOVE FRONT SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)

a.
B404491

Detach the claw and remove the front side rail spacer LH.


Hide 66413B 45.REMOVE FRONT SIDE RAIL SPACER RH (w/o Curtain Shield Airbag)

a.
B404492

Detach the claw and remove the front side rail spacer RH.


Hide 66424 46.REMOVE REAR SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)

a.
B404641

Detach the claw and remove the rear side rail spacer LH.


Hide 66414A 47.REMOVE REAR SIDE RAIL SPACER RH (w/o Curtain Shield Airbag)

a.
B404642

Detach the claw and remove the rear side rail spacer RH.


Hide 66425A 48.REMOVE REAR NO. 2 SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)

a.
B404643

Detach the claw and remove the rear No. 2 side rail spacer LH.


Hide 66415A 49.REMOVE REAR NO. 2 SIDE RAIL SPACER RH (w/o Curtain Shield Airbag)

a.
B404644

Detach the claw and remove the rear No. 2 side rail spacer RH.