Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION
1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
3.REMOVE FRONT SEAT ASSEMBLY LH
for Manual Seat:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>REMOVAL
for Bench Seat Type:
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Bench Seat Type)>REMOVAL
4.REMOVE FRONT SEAT ASSEMBLY RH
74610A
5.REMOVE ASSIST GRIP SUB-ASSEMBLY (w/ Assist Grip)
62212
6.REMOVE FRONT PILLAR GARNISH LH
62211
7.REMOVE FRONT PILLAR GARNISH RH
67914B
8.REMOVE FRONT DOOR SCUFF PLATE LH
| *a | Protective Tape |
Put protective tape around the front door scuff plate LH.
|
Insert Moulding Remover D Here |
|
Remove in this Direction |
Insert moulding remover D at the position shown in the illustration and pull as shown to detach the clip and claw and remove the front door scuff plate LH.
67913B
9.REMOVE FRONT DOOR SCUFF PLATE RH
| *a | Protective Tape |
Put protective tape around the front door scuff plate RH.
|
Insert Moulding Remover D Here |
|
Remove in this Direction |
Insert moulding remover D at the position shown in the illustration and pull as shown to detach the clip and claw and remove the front door scuff plate RH.
64261C
10.REMOVE UPPER BACK PANEL GARNISH
| *a | Protective Tape |
Put protective tape around the upper back panel garnish.
|
Place Hands Here |
|
Remove in this Direction |
Place your hands at the position shown in the illustration and pull as shown to detach the claw and clip and remove the upper back panel garnish.
62514A
11.REMOVE LOWER QUARTER TRIM PANEL LH
| *1 | Front Door Opening Trim Weatherstrip LH |
Disconnect the front door opening trim weatherstrip LH in the range shown in the illustration.
Remove the bolt and disconnect the front seat outer belt assembly LH.
|
Place Hands Here |
|
Remove in this Direction |
Place your hands at the position shown in the illustration and pull as shown to detach the claw and clip and remove the lower quarter trim panel LH.
62513A
12.REMOVE LOWER QUARTER TRIM PANEL RH
| *1 | Front Door Opening Trim Weatherstrip RH |
Disconnect the front door opening trim weatherstrip RH in the range shown in the illustration.
Remove the bolt and disconnect the front seat outer belt assembly RH.
|
Place Hands Here |
|
Remove in this Direction |
Place your hands at the position shown in the illustration and pull as shown to detach the claw and clip and remove the lower quarter trim panel RH.
73178A
13.REMOVE SEAT BELT ANCHOR COVER CAP
Use the same procedure for both seat belt anchor cover caps.
| *a | Protective Tape |
Put protective tape around the seat belt anchor cover cap.
| *a | Protective Tape |
|
Insert Thin-bladed Screwdriver Here |
|
Remove in this Direction |
Insert a thin-bladed screwdriver at the position shown in the illustration and detach the claw and remove the seat belt anchor cover cap.
Tape the thin-bladed screwdriver tip before use.
62512
14.REMOVE QUARTER INSIDE TRIM BOARD LH
Remove the bolt and disconnect the front seat outer belt assembly LH.
| *1 | Front Door Opening Trim Weatherstrip LH |
Disconnect the front door opening trim weatherstrip LH in the range shown in the illustration.
|
Insert Clip Remover Here |
|
Remove in this Direction |
Insert a clip remover at the position shown in the illustration and pull as shown to detach the clip and remove the quarter inside trim board LH.
62511
15.REMOVE QUARTER INSIDE TRIM BOARD RH
Remove the bolt and disconnect the front seat outer belt assembly RH.
| *1 | Front Door Opening Trim Weatherstrip RH |
Disconnect the front door opening trim weatherstrip RH in the range shown in the illustration.
|
Insert Clip Remover Here |
|
Remove in this Direction |
Insert a clip remover at the position shown in the illustration and pull as shown to detach the clip and remove the quarter inside trim board RH.
81260A
16.REMOVE MAP LIGHT ASSEMBLY
w/ Overhead Console:
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
w/o Overhead Console:
Click hereVehicle Interior>LIGHTING (INT)>ROOM LIGHT>REMOVAL
74325
17.REMOVE VISOR BRACKET COVER LH
Open the visor assembly LH.
| *a | Protective Tape |
|
Insert Thin-bladed Screwdriver Here |
Insert a thin-bladed screwdriver at the position shown in the illustration and detach the claw and remove the visor bracket cover LH.
Tape the thin-bladed screwdriver tip before use.
74325
18.REMOVE VISOR BRACKET COVER RH
Open the visor assembly RH.
| *a | Protective Tape |
|
Insert Thin-bladed Screwdriver Here |
Insert a thin-bladed screwdriver at the position shown in the illustration and detach the claw and remove the visor bracket cover RH.
Tape the thin-bladed screwdriver tip before use.
74320
19.REMOVE VISOR ASSEMBLY LH
Remove the 2 screws.
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Pull in the direction (1) shown in the illustration to disconnect the visor assembly LH from the visor holder.
Pull in the direction (2) shown in the illustration to remove the visor assembly LH.
74310
20.REMOVE VISOR ASSEMBLY RH
Remove the 2 screws.
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Pull in the direction (1) shown in the illustration to disconnect the visor assembly RH from the visor holder.
Pull in the direction (2) shown in the illustration to remove the visor assembly RH.
74348
21.REMOVE VISOR HOLDER
Use the same procedure for both visor holders.
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Turn the visor holder clockwise approximately 45° and pull it out as shown in the illustration.
Detach the claw and remove the visor holder.
74610A
22.REMOVE ASSIST GRIP SUB-ASSEMBLY
w/ Assist Grip:
Use the same procedure for both assist grip sub-assemblies.
| *a | Protective Tape |
Put protective tape around the assist grip sub-assembly.
| *a | Protective Tape |
|
Insert Thin-bladed Screwdriver Here |
|
Remove in this Direction |
Insert a thin-bladed screwdriver at the position shown in the illustration and detach the claw and open the assist grip cover.
Tape the thin-bladed screwdriver tip before use.
Remove the 2 bolts and assist grip sub-assembly.
63339A
23.REMOVE ROOF HEADLINING SERVICE HOLE COVER (w/o Assist Grip)
Using a clip remover, remove the 2 roof headlining service hole covers.
63310
24.REMOVE ROOF HEADLINING ASSEMBLY
Disconnect the connector and detach the clamp from the front pillar LH.
| *1 | Front Door Opening Trim Weatherstrip LH |
Disconnect the front door opening trim weatherstrip LH in the range shown in the illustration.
| *1 | Front Door Opening Trim Weatherstrip RH |
Disconnect the front door opening trim weatherstrip RH in the range shown in the illustration.
w/ Overhead Console:
Using a clip remover, remove the 3 clips.
|
Remove in this Direction |
Turn the roof headlining assembly diagonally and bend slightly to remove it from the front door.
Make sure wrinkles do not form in the roof headlining assembly during removal.
Make sure that the roof headlining assembly does not get caught on anything as it may become bent or damaged.
Do not damage the roof headlining assembly or vehicle interior.
w/o Overhead Console:
Using a clip remover, remove the 3 clips.
|
Remove in this Direction |
Turn the roof headlining assembly diagonally and bend slightly to remove it from the front door.
Make sure wrinkles do not form in the roof headlining assembly during removal.
Make sure that the roof headlining assembly does not get caught on anything as it may become bent or damaged.
Do not damage the roof headlining assembly or vehicle interior.
66423
25.REMOVE FRONT SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)
Detach the claw and remove the front side rail spacer LH.
66413B
26.REMOVE FRONT SIDE RAIL SPACER RH (w/o Curtain Shield Airbag)
Detach the claw and remove the front side rail spacer RH.
66424
27.REMOVE REAR SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)
Detach the claw and remove the rear side rail spacer LH.
66414A
28.REMOVE REAR SIDE RAIL SPACER RH (w/o Curtain Shield Airbag)
Detach the claw and remove the rear side rail spacer RH.