Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
| *1 | Centering Bolt |
| *2 | Standard Bolt |
Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts on. Substitute the centering bolts for standard bolts when making adjustments.
A bolt without a torque specification is shown in the standard bolt chart.
Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS
1. PRECAUTION (w/ Curtain Shield Airbag)
Be sure to read Precaution thoroughly before servicing.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Curtain Shield Airbag)
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
67002
3.INSPECT FRONT DOOR PANEL SUB-ASSEMBLY LH
Check that the clearance measurements of areas A to J are within the standard ranges.
| A | 2.8 to 5.8 mm (0.110 to 0.228 in.) | B | 3.2 to 6.2 mm (0.126 to 0.244 in.) |
| C | *1: 2.4 to 5.4 mm (0.094 to 0.213 in.)
*4: 2.2 to 5.2 mm (0.087 to 0.205 in.) |
D | 3.2 to 6.2 mm (0.126 to 0.244 in.) |
| E | 2.5 to 5.5 mm (0.098 to 0.217 in.) | F | *2: 3.2 to 6.2 mm (0.126 to 0.244 in.)
*3: 2.8 to 5.8 mm (0.110 to 0.228 in.) |
| G | -1.5 to 1.5 mm (-0.059 to 0.059 in.) | H | *2: 3.2 to 6.2 mm (0.126 to 0.244 in.)
*3: 2.8 to 5.8 mm (0.110 to 0.228 in.) |
| I | -1.5 to 1.5 mm (-0.059 to 0.059 in.) | J | 4.2 to 7.2 mm (0.165 to 0.283 in.) |
*1: for Single Cab, Smart Cab
*2: for Smart Cab, Double Cab
*3: for Single Cab
*4: for Double Cab
67002
4.ADJUST FRONT DOOR PANEL SUB-ASSEMBLY LH
Using SST, loosen the hinge bolts on the body and adjust the door position.
Tighten the hinge bolts on the body after the adjustment.
Loosen the hinge bolts on the door and adjust the door position.
Tighten the hinge bolts on the door after the adjustment.
Using a T40 "TORX" socket wrench, adjust the striker position by slightly loosening the striker mounting screws and hitting the striker with a plastic-faced hammer.
Using a T40 "TORX" socket wrench, tighten the striker mounting screws after the adjustment.
5.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (w/ Curtain Shield Airbag)
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
6.CHECK SRS WARNING LIGHT (w/ Curtain Shield Airbag)