Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR(for Smart Cab)
RM33J0E _59 Vehicle Exterior _038495 DOOR / HATCH _0193480 REAR DOOR(for Smart Cab) N

DOOR / HATCH  REAR DOOR(for Smart Cab)  ADJUSTMENT  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·
B276679C19
0.621,1.754 0.818,1.944 0.197,0.19 10 *1 2.535,1.754 2.732,1.944 0.197,0.19 10 *2
*1 Centering Bolt
*2 Standard Bolt


Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts on. Substitute the centering bolts for standard bolts when making adjustments.

·

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS



PROCEDURE

Hide 67004J 1.INSPECT ACCESS PANEL PANEL SUB-ASSEMBLY LH

a.

Check that the clearance measurements of areas A to I are within the standard ranges.

B404392N01
1.375,2.5 1.531,2.698 0.156,0.198 10 false A 1.958,2.688 2.115,2.885 0.156,0.198 10 false B 1.385,0.896 1.542,1.094 0.156,0.198 10 false C 1.948,1.073 2.104,1.271 0.156,0.198 10 false D 4.469,0.396 4.625,0.594 0.156,0.198 10 false E 4.552,0.729 4.708,0.927 0.156,0.198 10 false F 5.604,1.302 5.76,1.5 0.156,0.198 10 false G 5.677,1.635 5.833,1.833 0.156,0.198 10 false H 4.896,2.969 5.052,3.167 0.156,0.198 10 false I

Standard Clearance:
Area Measurement Area Measurement
A 3.2 to 6.2 mm (0.126 to 0.244 in.) B -1.5 to 1.5 mm (-0.059 to 0.059 in.)
C 3.2 to 6.2 mm (0.126 to 0.244 in.) D -1.5 to 1.5 mm (-0.059 to 0.059 in.)
E 3.2 to 6.2 mm (0.126 to 0.244 in.) F 2.5 to 5.5 mm (0.098 to 0.217 in.)
G 3.2 to 6.2 mm (0.126 to 0.244 in.) H -1.5 to 1.5 mm (-0.059 to 0.059 in.)
I 4.2 to 7.2 mm (0.165 to 0.283 in.) - -



Hide 67004J 2.ADJUST ACCESS PANEL PANEL SUB-ASSEMBLY LH

a.
B404390

Using SST, loosen the hinge bolts on the body and adjust the access panel position.

SST
09812-00010  


b.

Tighten the hinge bolts on the body after the adjustment.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


c.
B404391

Loosen the hinge bolts on the access panel and adjust the access panel position.


d.

Tighten the hinge bolts on the access panel after the adjustment.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


e.

f.
B404394

Remove the 2 screws and roof side rail garnish insert LH.


g.
B404395

Using a T40 "TORX" socket wrench, adjust the striker position by slightly loosening the striker mounting screws and hitting the striker with a plastic-faced hammer and brass bar.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)


h.
B404396

Using a T40 "TORX" socket wrench, adjust the striker position by slightly loosening the striker mounting screws and hitting the striker with a plastic-faced hammer.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)


i.
B404394

Install the roof side rail garnish insert LH with the 2 screws.