Home › Vehicle Exterior › DOOR / HATCH › TAIL GATE
RM33J0E _59 Vehicle Exterior _038495 DOOR / HATCH _0193485 TAIL GATE N

DOOR / HATCH  TAIL GATE  ADJUSTMENT  


PROCEDURE

Hide 65700 1.INSPECT REAR BODY TAIL GATE ASSEMBLY (for A Deck)

a.

Check that the clearance measurements of areas A to H are within the standard ranges.

B405443N01
2.74,0.219 2.896,0.417 0.156,0.198 10 false A 4.49,0.229 4.646,0.427 0.156,0.198 10 false C 2.302,0.417 2.458,0.615 0.156,0.198 10 false B 4.667,0.427 4.823,0.625 0.156,0.198 10 false D 2.688,2.625 2.844,2.823 0.156,0.198 10 false E 2.917,2.875 3.073,3.073 0.156,0.198 10 false F 4.563,2.635 4.719,2.833 0.156,0.198 10 false G 4.031,2.844 4.188,3.042 0.156,0.198 10 false H

Standard:
Area Specified Condition Area Specified Condition
A *1:4.7 to 5.0 mm (0.185 to 0.197 in.)
*2:4.85 to 5.15 mm (0.191 to 0.203 in.)
B -1.5 to 1.5 mm (-0.059 to 0.059 in.)
C *1:4.7 to 5.0 mm (0.185 to 0.197 in.)
*2:4.85 to 5.15 mm (0.191 to 0.203 in.)
D -1.5 to 1.5 mm (-0.059 to 0.059 in.)
E *1:4.7 to 5.0 mm (0.185 to 0.197 in.)
*2:4.85 to 5.15 mm (0.191 to 0.203 in.)
F -1.5 to 1.5 mm (-0.059 to 0.059 in.)
G *1:4.7 to 5.0 mm (0.185 to 0.197 in.)
*2:4.85 to 5.15 mm (0.191 to 0.203 in.)
H -1.5 to 1.5 mm (-0.059 to 0.059 in.)


*1: for Standard Body

*2: for Wide Body


Hide 65700 2.ADJUST REAR BODY TAIL GATE ASSEMBLY (for A Deck)

a.

Loosen the hinge bolts on the rear body tail gate assembly.


b.

Adjust the rear body tail gate assembly by moving it left and right so that the clearance measurements are within the specified ranges.


c.

Tighten the hinge bolts on the rear body tail gate assembly after the adjustment.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

B405444


Hide 65700 3.INSPECT REAR BODY TAIL GATE ASSEMBLY (for J Deck)

a.

Check that the clearance measurements of areas A to H are within the standard ranges.

B405445N01
2.75,0.146 2.906,0.344 0.156,0.198 10 false A 2.313,0.354 2.469,0.552 0.156,0.198 10 false B 4.188,0.156 4.344,0.354 0.156,0.198 10 false C 4.604,0.365 4.76,0.563 0.156,0.198 10 false D 2.427,2.615 2.583,2.813 0.156,0.198 10 false E 2.927,2.833 3.01,3.042 0.083,0.208 10 false F 4.292,2.604 4.458,2.792 0.167,0.188 10 false G 4.052,2.823 4.292,3.031 0.24,0.208 10 false H

Standard:
Area Specified Condition Area Specified Condition
A 4.7 to 5.0 mm (0.185 to 0.197 in.) B -1.5 to 1.5 mm (-0.059 to 0.059 in.)
C 4.7 to 5.0 mm (0.185 to 0.197 in.) D -1.5 to 1.5 mm (-0.059 to 0.059 in.)
E 4.7 to 5.0 mm (0.185 to 0.197 in.) F -1.5 to 1.5 mm (-0.059 to 0.059 in.)
G 4.7 to 5.0 mm (0.185 to 0.197 in.) H -1.5 to 1.5 mm (-0.059 to 0.059 in.)



Hide 65700 4.ADJUST REAR BODY TAIL GATE ASSEMBLY (for J Deck)

a.

Loosen the hinge bolts on the rear body tail gate assembly.


b.

Adjust the rear body tail gate assembly by moving it left and right so that the clearance measurements are within the specified ranges.


c.

Tighten the hinge bolts on the rear body tail gate assembly after the adjustment.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

B405446