Home › Vehicle Exterior › WIPER / WASHER › FRONT WIPER MOTOR
RM33J0E _59 Vehicle Exterior _038509 WIPER / WASHER _0193634 FRONT WIPER MOTOR A

WIPER / WASHER  FRONT WIPER MOTOR  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 85110 1.INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY

a.
B407761

Using a T30 "TORX" socket wrench, install the windshield wiper motor assembly with the 2 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


b.
B407762C01
1.333,0.646 1,0.458 true 0.792,0.354 1.104,0.51 0.313,0.156 10 false *a
*a Front Wiper Crank Pivot


Apply MP grease to the front wiper crank pivot of the windshield wiper motor assembly.


c.
B407763C01
0,0 0,0 false
V113147

Install in this Direction


Connect the No. 1 windshield wiper link rod to the front wiper crank pivot of the windshield wiper motor assembly.


Hide 2.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

NOTICE:

Be careful not to damage the windshield when installing the windshield wiper motor and link assembly.


a.
B407764C01
1.448,2.969 1.01,3.094 true 0.813,3.01 1.042,3.177 0.229,0.167 10 true *1 3.229,0.677 3.385,0.875 0.156,0.198 10 true 1 0.063,0.594 0.219,0.792 0.156,0.198 10 true 2
*1 Motor Grommet
V100135

Bolt
V100136

Connector
V113147

Install in this Direction


Attach the motor grommet to temporarily install the windshield wiper motor and link assembly as shown in the illustration.


b.

Install the windshield wiper motor and link assembly with the 2 bolts in the order indicated in the illustration.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


c.

Connect the connector.


Hide 53383 3.INSTALL HOOD TO COWL TOP SEAL

a.
B407806

Attach the claw and clip to install the hood to cowl top seal.


Hide 55781E 4.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

a.
B407807C01
0,0 0,0 false
V113147

Install in this Direction


Push the cowl top ventilator louver sub-assembly as shown in the illustration to attach the guide.


b.
B407808C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw and install the cowl top ventilator louver sub-assembly.


c.
B407803

Install the 2 clips.


Hide 53867H 5.INSTALL FRONT FENDER TO COWL SIDE SEAL LH

a.
B407809C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Attach the guide and claw and install the front fender to cowl side seal LH as shown in the illustration.


Hide 53866J 6.INSTALL FRONT FENDER TO COWL SIDE SEAL RH

HINT:

Use the same procedure for the LH side.


Hide 53389B 7.INSTALL HOOD TO FRONT FENDER SEAL LH (w/ Seal)

a.
B407801

Attach the claw and install the hood to front fender seal LH.


Hide 53388D 8.INSTALL HOOD TO FRONT FENDER SEAL RH (w/ Seal)

HINT:

Use the same procedure described for the LH side.


Hide 53886G 9.INSTALL FENDER APRON MUDGUARD SEAL SUB-ASSEMBLY LH

a.
B407800

Attach the claw and clip and install the fender apron mudguard seal sub-assembly LH.


b.

Attach the clip and connect the hood to cowl top seal to the fender apron mudguard seal sub-assembly LH.


Hide 53885G 10.INSTALL FENDER APRON MUDGUARD SEAL SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 11.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH

a.

When reinstalling:

NOTICE:

Do not grind the serrations excessively.


i.
B407810C01
1.865,0.615 2.417,0.333 true 1.948,1.552 2.438,1.333 true 2.469,0.219 2.781,0.375 0.313,0.156 10 false *a 2.5,1.25 2.813,1.406 0.313,0.156 10 false *b
*a Wiper Arm Serrations
*b Wiper Pivot Serrations


Clean the wiper arm serrations.


ii.

Clean the wiper pivot serrations.



b.

Turn the ignition switch to ON.


c.

Operate the wiper switch and stop the windshield wiper motor assembly at the automatic stop (park) position.


d.

Turn the ignition switch off.


e.
B407824C01
2.479,3.26 2.292,2.99 false 1.021,0.875 1.156,0.615 false 1.573,1.979 1.708,1.719 false 2.531,4.302 2.427,4.083 false 0.073,0.104 0.417,0.375 0.344,0.271 12 true *A 0.115,2.479 0.427,2.76 0.313,0.281 12 false *B 2.115,2.885 2.427,3.042 0.313,0.156 10 false *a 1.479,2.01 1.792,2.167 0.313,0.156 10 false *b 0.76,1.625 0.979,1.792 0.219,0.167 10 true *c 2.313,1.583 2.521,1.75 0.208,0.167 10 true *d 1.688,4.01 1.885,4.177 0.198,0.167 10 true *e 3.052,3.885 3.365,4.042 0.313,0.156 10 false *f 1.208,0.51 1.521,0.667 0.313,0.156 10 false *a 2.479,4.333 2.792,4.49 0.313,0.156 10 false *b
*A for LHD
*B for RHD
*a Ceramic Dot
*b Louver Edge
*c 19.5 to 34.5 mm (0.7677 to 1.3583 in.)
*d 18.9 mm (0.7441 in.)
*e 24 mm (0.9449 in.)
*f 22.7 to 37.7 mm (0.8937 to 1.4842 in.)


Align the front wiper arm and blade assembly LH as shown in the illustration and install it with the nut.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)

HINT:

Hold the arm hinge by hand when tightening the nut.



f.

Operate the front wipers while spraying washer fluid on the glass. Make sure that the front wipers function properly and the wipers do not come into contact with the vehicle body.


g.

Raise the wiper arm 2 times and check that the tip of the front wiper blade is at the position shown in the illustration.


Hide 12.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH

a.

When reinstalling:

NOTICE:

Do not grind the serrations excessively.


i.
B407810C01
1.865,0.615 2.417,0.333 true 1.948,1.552 2.438,1.333 true 2.469,0.219 2.781,0.375 0.313,0.156 10 false *a 2.5,1.25 2.813,1.406 0.313,0.156 10 false *b
*a Wiper Arm Serrations
*b Wiper Pivot Serrations


Clean the wiper arm serrations.


ii.

Clean the wiper pivot serrations.



b.

Turn the ignition switch to ON.


c.

Operate the wiper switch and stop the windshield wiper motor assembly at the automatic stop (park) position.


d.

Turn the ignition switch off.


e.
B407825C01
2.219,3.24 2.083,3 false 0.896,0.688 0.771,0.938 false 0.792,1.74 0.667,1.99 false 1.688,4.344 1.552,4.104 false 0.104,0.115 0.448,0.354 0.344,0.24 12 false *A 0.135,2.49 0.448,2.802 0.313,0.313 12 false *B 0.906,0.552 1.219,0.708 0.313,0.156 10 false *a 0.604,2.031 0.917,2.188 0.313,0.156 10 false *b 0.115,1.521 0.427,1.677 0.313,0.156 10 false *c 1.385,1.719 1.573,1.906 0.188,0.188 10 true *d 0.75,3.958 0.938,4.135 0.188,0.177 10 true *e 2.271,4.01 2.458,4.177 0.188,0.167 10 true *f 1.896,2.896 2.208,3.052 0.313,0.156 10 false *a 1.667,4.385 1.979,4.542 0.313,0.156 10 false *b
*A for LHD
*B for RHD
*a Ceramic Dot
*b Louver Edge
*c 22.7 to 37.7 mm (0.8937 to 1.4842 in.)
*d 24 mm (0.9449 in.)
*e 18.9 mm (0.7441 in.)
*f 19.5 to 34.5 mm (0.7677 to 1.3583 in.)


Align the front wiper arm and blade assembly RH as shown in the illustration and install it with the nut.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)

HINT:

Hold the arm hinge by hand when tightening the nut.



f.

Operate the front wipers while spraying washer fluid on the glass. Make sure that the front wipers function properly and the wipers do not come into contact with the vehicle body.


g.

Raise the wiper arm 2 times and check that the tip of the front wiper blade is at the position shown in the illustration.


Hide 85292B 13.INSTALL FRONT WIPER ARM HEAD CAP

a.
B407813

Attach the claw and install the front wiper arm head cap.

HINT:

Use the same procedure for both front wiper arm head caps.