Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM(for Type A)
RM33J0E _58 Vehicle Interior _038501 SUPPLEMENTAL RESTRAINT SYSTEMS _0193719 AIRBAG SYSTEM(for Type A) D

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(for Type A)  DIAGNOSIS SYSTEM  


SYMPTOM SIMULATION


C206435E03
0.618,0.0 1.6,0.205 0.983,0.205 10 Vibrate Slightly 0.281,2.604 1.264,2.809 0.983,0.205 10 Shake Slightly 1.115,4.114 2.097,4.319 0.983,0.205 10 Vibrate Slightly

HINT:

The most difficult case in troubleshooting is when no problem symptoms occur. In such a case, a thorough problem analysis must be carried out. A simulation of the same or similar conditions and environment in which the problem occurred in the customer's vehicle should be carried out. No matter how much skill or experience a technician has, troubleshooting without confirming the problem symptoms will lead to important repairs being overlooked and mistakes or delays.


a.

Vibration method: When vibration seems to be the major cause.

HINT:

Perform the simulation method only during the primary check period (for approximately 6 seconds after the ignition switch is turned to ON).


i.

Slightly vibrate the part of the sensor considered to be the cause of the problem with your fingers and check whether the malfunction occurs.

NOTICE:

Shaking the relays too strongly may result in open relays.



ii.

Slightly shake the connector vertically and horizontally.


iii.

Slightly shake the wire harness vertically and horizontally.

HINT:

The connector joint and fulcrum of the vibration are the major areas to be checked thoroughly.





FUNCTION OF SRS WARNING LIGHT


a.

Primary check.

i.

Turn the ignition switch off. Wait for at least 2 seconds, and then turn the ignition switch to ON. The SRS warning light comes on for approximately 6 seconds and diagnosis of the airbag system (including the seat belt pretensioners) is performed.

HINT:

If trouble is detected during the primary check, the SRS warning light remains on even after the primary check period (of approximately 6 seconds) has elapsed.




b.

Constant check.

i.

After the primary check, the airbag sensor assembly constantly monitors the airbag system for trouble.

HINT:

If trouble is detected during the constant check, the airbag sensor assembly functions as follows:

·

The SRS warning light comes on.

·

The SRS warning light goes off, and then comes on. This blinking pattern indicates a source voltage drop. The SRS warning light goes off 10 seconds after the source voltage returns to normal.





c.

Review.

i.

When the airbag system is normal:

The SRS warning light comes on only during the primary check period (for approximately 6 seconds after the ignition switch is turned to ON).


ii.

When the airbag system has trouble:

·

The SRS warning light remains on even after the primary check period has elapsed.

·

The SRS warning light goes off after the primary check, but comes on again during the constant check.

·

The SRS warning light does not come on when turning the ignition switch from off to ON.


HINT:

The airbag sensor assembly functions to keep the SRS warning light on if the airbag has been deployed.





CHECK SRS WARNING LIGHT


a.
C093955

Turn the ignition switch to ON and check that the SRS warning light comes on for approximately 6 seconds (primary check).


b.

Check that the SRS warning light goes off approximately 6 seconds after the ignition switch is turned to ON (constant check).

HINT:

When any of the following symptoms occur, refer to the "Problem Symptoms Table".

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type A)>PROBLEM SYMPTOMS TABLE

·

The SRS warning light comes on occasionally after the primary check period has elapsed.

·

The SRS warning light comes on, but a DTC is not output.

·

The ignition switch is turned from off to ON, but the SRS warning light does not come on.





FUNCTION OF PASSENGER AIRBAG ON/OFF INDICATOR (w/ Airbag Cutoff Switch)


a.

Initial check

i.

Turn the ignition switch to ON.


ii.

The passenger airbag ON/OFF indicator comes on for approximately 4 seconds, and then goes off for approximately 2 seconds.


iii.

Approximately 6 seconds after the ignition switch is turned to ON, the passenger airbag ON/OFF indicator will be on or off according to the chart below.

HINT:

The timing chart below shows the operation of the passenger airbag ON/OFF indicator. Use the chart to check the indicator light circuit.


C280059E01
4.406,2.208 4.708,1.948 4.708,1.948 4.823,1.948 true 0.146,0.427 1.354,0.625 1.208,0.198 10 false Ignition Switch 0.125,1.302 1.51,2.052 1.385,0.75 10 false Passenger Airbag ON/OFF Indicator ("ON Indicator") 1.594,0.271 1.885,0.458 0.292,0.188 10 false ON 0.156,2.292 1.531,3.25 1.375,0.958 10 false Passenger Airbag ON/OFF Indicator ("OFF Indicator") 1.594,0.646 1.99,0.823 0.396,0.177 10 false Off 1.625,1.313 1.917,1.5 0.292,0.188 10 false On 1.646,1.688 2.042,1.865 0.396,0.177 10 false Off 1.625,2.333 1.917,2.521 0.292,0.188 10 false On 1.625,2.677 2.021,2.854 0.396,0.177 10 false Off 2.948,0.656 3.844,1.063 0.896,0.406 10 false Approximately 4 seconds 4.01,0.646 4.917,1.365 0.906,0.719 10 false Approximately 2 seconds 2.99,1.646 3.865,2.146 0.875,0.5 10 false Approximately 4 seconds 4.854,1.854 6.698,2.063 1.844,0.208 10 false Approximately 2 seconds 4.49,3.073 7.021,3.51 2.531,0.438 10 false ON/OFF condition depends on the front passenger detection results.




CHECK PASSENGER AIRBAG ON/OFF INDICATOR (w/ Airbag Cutoff Switch)


a.
C301817

Turn the ignition switch to ON.


b.

Check that the passenger airbag ON/OFF indicator ("ON" and "OFF") comes on for approximately 4 seconds, and then goes off for approximately 2 seconds.

HINT:

In order to check the operation of the passenger airbag ON/OFF indicator when approximately 6 seconds have elapsed after turning the ignition switch to ON.




FUNCTION OF SRS CONNECTORS


a.

SRS connectors are located as shown in the illustration.

C326669E06
4.875,0.281 6.594,0.5 1.719,0.219 10 false Airbag Sensor Assembly 5.052,0.979 6.49,1.177 1.438,0.198 10 false 1 6.031,0.969 6.188,1.156 0.156,0.188 10 false 3 5.563,1.115 5.719,1.302 0.156,0.188 10 false A 5.083,1.26 6.521,1.458 1.438,0.198 10 false 2 6.083,1.26 6.25,1.458 0.167,0.198 10 false 4 4.281,1.094 5.719,1.292 1.438,0.198 10 false 6 4.469,1.625 5.906,1.823 1.438,0.198 10 false 5 3.115,2.104 4.552,2.302 1.438,0.198 10 false 8 3.323,2.625 4.76,2.823 1.438,0.198 10 false 7 3.104,2.896 4.542,3.094 1.438,0.198 10 false 8 3.302,3.396 4.74,3.594 1.438,0.198 10 false 7 3.938,3.052 5.375,3.25 1.438,0.198 10 false 10 4.302,3.458 5.74,3.656 1.438,0.198 10 false 9 3.177,3.698 4.615,3.896 1.438,0.198 10 false 12 3.323,4.188 4.76,4.385 1.438,0.198 10 false 11 3.948,4.542 5.385,4.74 1.438,0.198 10 false 14 4.344,4.938 5.781,5.135 1.438,0.198 10 false 13 3.177,4.427 4.615,4.625 1.438,0.198 10 false 16 3.313,4.885 4.75,5.063 1.438,0.177 10 false 15 3.938,5.302 5.375,5.479 1.438,0.177 10 false 14 4.375,5.708 5.813,5.885 1.438,0.177 10 false 13 3.167,5.198 4.604,5.375 1.438,0.177 10 false 16 3.302,5.667 4.74,5.844 1.438,0.177 10 false 15 3.177,5.927 4.615,6.104 1.438,0.177 10 false 18 3.313,6.427 4.75,6.604 1.438,0.177 10 false 17 2.552,1.24 4.094,1.563 1.542,0.323 10 false Spiral with Sensor Cable Sub-assembly 0.604,2.281 2.219,2.51 1.615,0.229 10 false Horn Button Assembly 0.604,3.073 2.813,3.417 2.208,0.344 10 false Instrument Panel Passenger Airbag Assembly*1 0.625,3.833 2.917,4.292 2.292,0.458 10 false Lower No. 1 Instrument Panel Airbag Assembly*1 0.604,4.552 2.219,4.781 1.615,0.229 10 false Front Airbag Sensor RH 0.635,5.344 2.25,5.573 1.615,0.229 10 false Front Airbag Sensor LH 0.615,6.094 2.438,6.438 1.823,0.344 10 false Airbag Cutoff Switch Cylinder Sub-assembly*2 0.583,6.854 3.01,7.135 2.427,0.281 10 false Passenger Airbag ON/OFF Indicator*2 0.188,7.5 3.031,7.792 2.844,0.292 10 false *1: w/ Front Pretensioner 2.24,7.51 5.083,7.802 2.844,0.292 10 false *2: w/ Airbag Cutoff Switch

C326670C01
0.667,0.583 3.573,0.781 2.906,0.198 10 false Airbag Sensor Assembly 0.927,1.302 1.219,1.5 0.292,0.198 10 false 1 1.896,1.302 2.188,1.5 0.292,0.198 10 false 3 1.385,1.458 1.677,1.656 0.292,0.198 10 false A 0.917,1.594 1.208,1.792 0.292,0.198 10 false 2 1.896,1.594 2.188,1.792 0.292,0.198 10 false 4 4.208,1.75 7.115,1.948 2.906,0.198 10 false Front Seat Outer Belt Assembly LH* 4.25,2.521 7.156,2.719 2.906,0.198 10 false Front Seat Outer Belt Assembly RH* 3.948,1.552 4.24,1.75 0.292,0.198 10 false 20 3.708,2.042 4,2.24 0.292,0.198 10 false 19 3.885,2.302 4.177,2.5 0.292,0.198 10 false 20 3.688,2.813 3.979,3.01 0.292,0.198 10 false 19 0.063,0.042 2.969,0.24 2.906,0.198 12 false for Single Cab, Double Cab: 0.115,3.51 3.021,3.708 2.906,0.198 10 false *: w/ Front Pretensioner

C330285E01
0.594,0.573 3.5,0.771 2.906,0.198 10 false Airbag Sensor Assembly 4.25,1.688 7.156,1.885 2.906,0.198 10 false Front Seat Outer Belt Assembly LH 4.25,2.469 7.156,2.667 2.906,0.198 10 false Front Seat Outer Belt Assembly RH 3.99,1.552 4.563,1.781 0.573,0.229 10 false 20 3.979,2.313 4.552,2.542 0.573,0.229 10 false 20 3.729,2.813 4.302,3.042 0.573,0.229 10 false 19 3.719,2 4.292,2.229 0.573,0.229 10 false 19 3.292,1.688 3.865,1.917 0.573,0.229 10 false 10 3.292,2.417 3.865,2.646 0.573,0.229 10 false 10 3.063,2.021 3.635,2.25 0.573,0.229 10 false 9 3.063,2.771 3.635,3 0.573,0.229 10 false 9 0.094,0.083 3.052,0.385 2.958,0.302 12 false for Smart Cab: 0.854,1.313 1.427,1.542 0.573,0.229 10 false 1 1.885,1.313 2.458,1.542 0.573,0.229 10 false 3 0.854,1.604 1.438,1.865 0.583,0.26 10 false 2 1.896,1.604 2.479,1.865 0.583,0.26 10 false 4 1.354,1.448 1.938,1.708 0.583,0.26 10 false A

Connector Type Application
Terminal Twin-Lock Mechanism Connectors 5, 10, 13, 15
Half Connection Prevention Mechanism Connectors 5, 10
Activation Prevention Mechanism Connectors 2, 4, 6, 10
Connector Lock Mechanism (1) Connectors 7, 11, 19
Connector Position Assurance Mechanism Connectors 14, 16
Connector Lock Mechanism (2) Connectors A
Improper Connection Prevention Lock Mechanism Connectors A


b.

Terminal twin-lock mechanism

C190972E10
2.469,1.521 2.292,1.521 2.292,1.521 1.896,1.021 false 5.708,0.094 5.573,0.094 false 5.823,0.635 5.708,0.094 false 2.573,1.438 3.927,1.615 1.354,0.177 10 false Lance (Primary Lock) 1.229,1.448 2.167,1.625 0.938,0.177 10 false Primary Lock 3.948,0.021 5.625,0.198 1.677,0.177 10 false Spacer (Secondary Lock) 4.896,1.427 5.948,1.604 1.052,0.177 10 false Secondary Lock

i.

This mechanism is designed to increase the ability of the terminal to remain connected and prevent it from accidentally being disconnected.


ii.

The connector has a two-piece construction consisting of the housing and spacer to securely lock the terminal using both the lance (primary lock) and spacer (secondary lock).



c.

Half connection prevention mechanism

C147461E18
1.427,1.083 1.271,1.073 false 1.552,1.417 1.427,1.083 false 1.719,0.813 1.5,0.813 false 1.833,1.365 1.719,0.813 false 2.146,0.531 1.938,0.531 false 2.354,1.344 2.146,0.531 false 3.219,0.563 3.406,0.563 false 2.99,1.198 3.219,0.563 false 3.458,0.865 3.635,0.875 false 3.25,1.323 3.458,0.865 false 5.917,0.74 5.729,0.74 false 6.073,1.146 5.917,0.74 false 1.125,0.458 1.958,0.625 0.833,0.167 10 Locking Arm 0.979,0.729 1.521,0.896 0.542,0.167 10 Stopper 0.469,1 1.302,1.177 0.833,0.177 10 Locking Part 3.448,0.5 3.885,0.688 0.438,0.188 10 Slider 3.667,0.802 4.135,0.99 0.469,0.188 10 Spring 5.177,0.646 5.76,0.833 0.583,0.188 10 Stopper 4.708,1.906 6.042,2.094 1.333,0.188 10 Rebound by Slider

i.

This mechanism is designed to prevent the connector from being connected only halfway.


ii.

If the connector is not completely connected, the connector is disconnected by the force of the spring so that no continuity exists.



d.

Activation prevention mechanism

C269646E04
2.781,1.271 3.313,1 3.313,1 2.885,1.354 true 1.5,1.333 1.833,1.333 true 1.563,1.75 1.75,1.75 1.75,1.75 1.875,1.51 true 6.063,3.448 6.198,3.865 6.198,3.865 6.219,3.427 true 2.927,3.198 3.146,3.906 3.146,3.906 3.198,3.208 true 1.271,3.24 1.427,3.865 1.427,3.865 1.448,3.219 true 1.583,0.833 1.75,0.833 1.75,0.833 1.917,1.021 true 2.99,1.583 3.25,1.417 3.25,1.417 3.417,1.417 true 4.667,1.833 4.833,1.833 4.833,1.833 5.146,1.365 true 1.417,3.844 0.917,3.229 true 2.031,0.323 2.906,0.531 0.875,0.208 10 false When open 3.354,0.906 4.51,1.115 1.156,0.208 10 false Female Terminal 3.458,1.344 4.615,1.552 1.156,0.208 10 false Female Housing 0.698,0.74 1.677,0.948 0.979,0.208 10 false Male Housing 0.625,1.25 1.615,1.448 0.99,0.198 10 false Male Terminal 0.406,1.656 1.635,1.854 1.229,0.198 10 false Short Spring Plate 2.896,1.74 4.667,2.094 1.771,0.354 10 false Short spring plate contacting the male terminal 4.406,2.042 6.938,2.656 2.531,0.615 10 false Component without harness connected: (Spiral with Sensor Cable Sub-assembly) 5.844,3.896 6.875,4.104 1.031,0.208 10 false Short Spring 0.958,2.354 3.25,2.75 2.292,0.396 10 false Front view of wire harness connector: (to Airbag Sensor Assembly) 2.802,3.906 3.833,4.115 1.031,0.208 10 false Short Spring 1.104,3.906 2.135,4.115 1.031,0.208 10 false Short Spring 5.333,0.333 6.417,0.542 1.083,0.208 10 false When shorted

i.

The activation prevention mechanism is designed to create a short circuit automatically between the positive (+) and negative (-) terminals of an airbag power source connector when disconnected.


ii.

The short spring plate contained in the connector creates a closed circuit on the airbag side (no potential difference can occur between both terminals), preventing accidental airbag deployment when servicing.



e.

Connector lock mechanism (1)

C147462E12
2.521,0.354 2.021,0.198 false 2.635,0.802 2.281,0.885 false 2.469,1.24 2.271,1.323 false 4.927,0.896 5.24,0.688 false 0.531,0.115 2.01,0.292 1.479,0.177 10 Lock the locking button 1.927,0.813 2.302,0.979 0.375,0.167 10 Claw 1.792,1.25 2.281,1.417 0.49,0.167 10 Groove 5.281,0.604 6.99,0.938 1.708,0.333 10 Claw on the locking button is locked in the groove

i.

This mechanism is designed to prevent the connector from accidentally being disconnected.


ii.

Locking the connector locking button engages the locking button claw in the groove of the other connector to connect the connector securely.



f.

Connector Position Assurance (CPA) mechanism

C161464E01
1.058,0.13 2.269,0.299 1.211,0.170 10 Female Connector 1.261,0.41 2.097,0.580 0.836,0.170 10 Locking Part 1.003,2.219 2.062,2.396 1.059,0.177 10 Male Connector 2.963,0.298 4.550,0.454 1.586,0.156 10 Primary Lock Completed 5.072,0.298 6.839,0.454 1.767,0.156 10 Secondary Lock Completed 4.898,0.699 5.526,0.875 0.628,0.177 10 Retainer 0.858,0.198 1.016,0.2 false 0.837,1.105 0.858,0.198 false 1.051,0.478 1.217,0.478 false 0.933,1.2 1.051,0.478 false 0.727,2.289 0.958,2.289 false 0.511,1.797 0.727,2.289 false 5.63,0.779 5.464,0.779 false 5.66,1.096 5.63,0.779 false

i.

This mechanism is designed to detect when the connector is connected only halfway.


ii.

The CPA and female connector slide to the male connector side at the same time and the primary lock is completed when the female connector is engaged with the male connector. From this point, only the CPA slides to the male connector side. The secondary lock is completed when the CPA retainer is engaged with the female connector. When the CPA and female connector ends are aligned, the connectors are completely engaged.



g.

Connector lock mechanism (2)

C269644E03
0.833,1.792 1,1.792 1,1.792 1.281,1.417 false 4.802,1.75 4.635,1.75 4.635,1.75 4.385,1.417 false 2.427,3.469 2.26,3.469 2.26,3.469 1.969,3.052 false 4.969,3.583 5.135,3.583 5.135,3.583 5.417,3.208 false 3.719,3.125 3.885,3.125 3.885,3.125 4.167,2.75 false 5.375,2.51 5.542,2.51 5.542,2.51 5.677,2.667 false 5.969,2.25 5.802,2.25 5.802,2.25 5.792,2.615 false 0.438,1.698 1.208,1.896 0.771,0.198 10 false Lance 4.833,1.667 5.604,1.865 0.771,0.198 10 false Holder 2.469,3.385 3.24,3.583 0.771,0.198 10 false Retainer 3.188,3.031 3.958,3.229 0.771,0.198 10 false Retainer 4.448,3.479 5.219,3.677 0.771,0.198 10 false Retainer 4.938,2.417 5.708,2.615 0.771,0.198 10 false Holder 6,2.167 6.771,2.365 0.771,0.198 10 false Claw

i.

This mechanism is designed to prevent the connector from accidentally being disconnected.


ii.

Sliding the connector all the way into the holder and locking the lance completes the primary lock.


iii.

Engaging the retainer with the holder as shown in the illustration completes the secondary lock, preventing the connector from accidentally being disconnected.



h.

Improper connection prevention lock mechanism

C269645E03
4.573,1.583 4.74,1.583 4.74,1.583 5.021,1.01 false 5.448,0.188 5.281,0.188 5.281,0.188 5.031,0.604 false 4.292,3.156 4.458,3.156 4.458,3.156 4.625,3.333 false 1.01,2.677 1.177,2.677 1.177,2.677 1.385,1.521 false 1.823,0.646 1.656,0.646 1.656,0.646 1.406,1.063 false 3.604,0.063 4.375,0.26 0.771,0.198 10 false Top View 3.26,1.5 4.667,1.708 1.406,0.208 10 false Temporary Hold Lock 5.5,0.104 6.354,0.323 0.854,0.219 10 false Unlock Rib 3.948,3.073 4.406,3.25 0.458,0.177 10 false Lever 0.302,2.604 1.156,2.823 0.854,0.219 10 false Unlock Rib 1.854,0.552 2.708,0.771 0.854,0.219 10 false A

i.

This mechanism is designed to prevent the connector from being connected only halfway.


ii.

When the holder is connected to the airbag sensor assembly, the unlock rib unlocks the temporary hold lock, allowing the lever to be pushed in by rotating around the A axis.


iii.

Locking the lever to the holder locks the holder securely.




ACTIVATION PREVENTION MECHANISM


a.

Function of activation prevention mechanism

i.

An activation prevention mechanism is built into the connector (on the airbag sensor assembly side) of the airbag system squib circuit to prevent accidental airbag activation.


ii.

This mechanism closes the circuit when the connector is disconnected by bringing the short spring into contact with the terminals and insulating the circuit from external power sources to prevent accidental airbag activation.



b.

Releasing of activation prevention mechanism

i.

To release the activation prevention mechanism, insert a piece of paper with the same thickness as the male terminal (approximately 0.5 mm [0.0197 in.]) between the terminals and short spring to break the connection.


ii.

Refer to the following illustrations concerning connectors utilizing the activation prevention mechanism and its release method.

CAUTION:

Never release the activation prevention mechanism on the squib connector even when inspecting with the squib disconnected.


NOTICE:
·

Do not release the activation prevention mechanism unless specially directed by the troubleshooting procedure.

·

To prevent the terminal and short spring from being damaged, always use a piece of paper with the same thickness as the male terminal.



C327225E02
2.396,0.531 2.823,0.75 0.427,0.219 4.5,0.573 4.927,0.792 0.427,0.219 0.938,4.563 1.365,4.781 0.427,0.219 0.927,7.031 1.354,7.25 0.427,0.219 2.24,1.177 2.542,2.115 2.542,2.115 2.854,1.188 true 1.927,1.177 2.542,2.135 2.542,2.135 3.177,1.188 true 1.927,1.531 2.542,2.146 2.542,2.146 3.177,1.542 true 4.458,1.198 4.708,2.135 4.708,2.135 4.948,1.208 true 4.458,1.552 4.708,2.177 4.708,2.177 4.948,1.563 true 2.885,3.188 3.01,2.948 3.01,2.948 3.188,2.948 true 5.823,3.188 5.948,2.948 5.948,2.948 6.125,2.948 true 2.26,3.24 2.844,3.917 2.844,3.917 2.958,3.917 true 5.344,3.25 5.927,3.927 5.927,3.927 6.042,3.927 true 2.302,5.896 2.365,6.396 2.365,6.396 2.469,5.896 true 3.438,5.698 4.021,6.375 4.021,6.375 4.135,6.375 true 5.281,5.719 5.865,6.396 5.865,6.396 5.979,6.396 true 4.292,5.792 4.417,5.552 4.417,5.552 4.594,5.552 true 6.24,5.792 6.365,5.552 6.365,5.552 6.542,5.552 true 3.76,7.771 4,7.313 4,7.313 4.177,7.313 true 6.125,7.771 6.365,7.313 6.365,7.313 6.542,7.313 true 1.167,7.896 1.24,8.219 1.24,8.219 1.333,7.896 true 1.052,7.885 1.24,8.24 1.24,8.24 1.458,7.906 true 5.719,7.833 5.969,8.26 5.969,8.26 6.135,8.26 true 3.271,7.802 3.521,8.229 3.521,8.229 3.688,8.229 true 2.354,0.125 6.792,0.323 4.438,0.198 10 false Airbag Sensor Assembly Connector 2.573,0.552 3.021,0.802 0.448,0.25 10 false 2 4.688,0.594 5.135,0.844 0.448,0.25 10 false 4 2.177,2.156 3.135,2.542 0.958,0.385 10 false Short Spring 4.333,2.177 5.292,2.563 0.958,0.385 10 false Short Spring 1.594,2.646 2.552,3.031 0.958,0.385 10 false Before Release 4.542,2.646 5.5,3.031 0.958,0.385 10 false After Release 3.26,2.875 4.219,3.26 0.958,0.385 10 false Paper 6.188,2.896 7.146,3.281 0.958,0.385 10 false Paper 3.01,3.844 3.969,4.229 0.958,0.385 10 false Short Spring 6.104,3.865 7.063,4.25 0.958,0.385 10 false Short Spring 0.271,4.573 1.646,4.771 1.375,0.198 10 false Connector 1.125,4.583 1.573,4.833 0.448,0.25 10 false 6 2.031,6.438 2.99,6.823 0.958,0.385 10 false Short Spring 3.302,4.917 4.26,5.302 0.958,0.385 10 false Before Release 5.281,4.896 6.24,5.281 0.958,0.385 10 false After Release 4.188,6.313 5.146,6.698 0.958,0.385 10 false Short Spring 6.031,6.323 6.99,6.708 0.958,0.385 10 false Short Spring 4.24,7.25 4.813,7.51 0.573,0.26 10 false Paper 6.583,5.479 7.156,5.74 0.573,0.26 10 false Paper 4.667,5.469 5.24,5.729 0.573,0.26 10 false Paper 6.583,7.24 7.156,7.5 0.573,0.26 10 false Paper 0.896,8.26 1.854,8.646 0.958,0.385 10 false Short Spring 6.198,8.177 7.156,8.563 0.958,0.385 10 false Short Spring 3.75,8.156 4.708,8.542 0.958,0.385 10 false Short Spring 2.635,7.073 3.594,7.458 0.958,0.385 10 false Before Release 5.208,7.052 6.167,7.438 0.958,0.385 10 false After Release 0.25,7.042 1.625,7.24 1.375,0.198 10 false Connector 1.115,7.052 1.563,7.302 0.448,0.25 10 false 10