Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM(for Type B) › 2015.06–2016.07
RM33J0E _58 Vehicle Interior _038501 SUPPLEMENTAL RESTRAINT SYSTEMS _0193720 AIRBAG SYSTEM(for Type B) J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(for Type B)  Diagnosis Circuit  


DESCRIPTION

DTC output mode is set by connecting terminals TC and CG of the DLC3.

DTCs are output by the blinking of the SRS warning light.

HINT:
·

When each warning light continues blinking, a ground short in the wiring of terminal TC of the DLC3 or an internal ground short in each ECU is suspected.

·

A DTC output mode signal is transmitted through the CAN communication system to each ECU, including the airbag sensor assembly. Thus, when all systems do not enter DTC output mode, there may be an ECM malfunction.



WIRING DIAGRAM

C335930E01
1.792,1.823 2.104,2.021 0.313,0.198 10 false TC 2.104,1.833 2.417,2.031 0.313,0.198 10 false G46 2.49,1.833 2.802,2.031 0.313,0.198 10 false G84 2.885,1.833 3.198,2.031 0.313,0.198 10 false G85 2.083,1.625 2.458,1.823 0.375,0.198 10 false 19*1 2.479,1.625 2.854,1.823 0.375,0.198 10 false 11*2 2.885,1.625 3.26,1.823 0.375,0.198 10 false 25*3 1.469,2.583 1.99,2.76 0.521,0.177 10 false ECM 1.802,3.521 2.115,3.719 0.313,0.198 10 false TC 5.917,4.781 6.313,4.958 0.396,0.177 10 false G46 1.302,3.531 1.615,3.729 0.313,0.198 10 false CG 1.125,3.427 1.438,3.625 0.313,0.198 10 false 4 1.448,4.021 1.76,4.219 0.313,0.198 10 false G8 1.479,4.188 2.198,4.375 0.719,0.188 10 false DLC3 0.51,5.49 2.469,5.677 1.958,0.188 10 false : CAN Communication Line 0.219,4.646 2.177,4.833 1.958,0.188 10 false *1: for 2TR-FE 0.219,4.917 2.177,5.104 1.958,0.188 10 false *2: for 1KD-FTV, 2KD-FTV 0.208,5.208 2.167,5.396 1.958,0.188 10 false *3: for 1GD-FTV, 2GD-FTV 5.917,4.938 6.813,5.302 0.896,0.365 10 false Airbag Sensor Assembly 2.083,3.406 2.396,3.604 0.313,0.198 10 false 13

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After replacing the airbag sensor assembly, refer to initialization*.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

*: w/ VSC



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM

Result:
Proceed to
DTCs are output (for LHD)
DTCs are output (for RHD)
DTC is not output



DTCs are output (for LHD)

DTCs are output (for RHD)

DTC is not output

2.CHECK HARNESS AND CONNECTOR (DLC3 - ECM)
2.CHECK HARNESS AND CONNECTOR (DLC3 - ECM)
a.

Turn the ignition switch off.

C335931C01
6.063,0.531 6.521,0.813 0.458,0.281 0.583,0.51 1.042,0.792 0.458,0.281 2.521,0.521 2.979,0.802 0.458,0.281 4.25,0.521 4.708,0.802 0.458,0.281 0.896,2.323 0.708,2.323 0.708,2.323 0.427,1.76 true 2.188,2.313 2.354,2.313 2.354,2.313 2.563,1.615 true 4.479,2.333 4.646,2.333 4.646,2.333 4.833,1.719 true 6.021,2.333 6.188,2.333 6.188,2.333 6.375,1.719 true 1.125,0.573 1.438,0.729 0.313,0.156 10 false *A 3.052,0.573 3.365,0.729 0.313,0.156 10 false *B 4.792,0.615 5.104,0.771 0.313,0.156 10 false *C 0.083,0.24 0.396,0.396 0.313,0.156 10 false *a 5.521,0.344 5.833,0.5 0.313,0.156 10 false *b 0.688,0.583 1.073,0.771 0.385,0.188 10 false G46 2.615,0.573 3,0.76 0.385,0.188 10 false G84 4.344,0.583 4.729,0.771 0.385,0.188 10 false G85 6.167,0.594 6.552,0.781 0.385,0.188 10 false G8 2.115,0.281 2.427,0.438 0.313,0.156 10 false *a 3.927,0.302 4.24,0.458 0.313,0.156 10 false *a 0.969,2.219 1.354,2.406 0.385,0.188 10 false TC 1.948,2.24 2.333,2.427 0.385,0.188 10 false TC 4.26,2.25 4.646,2.438 0.385,0.188 10 false TC 5.813,2.25 6.198,2.438 0.385,0.188 10 false TC
*A for 2TR-FE *B for 1KD-FTV, 2KD-FTV
*C for 1GD-FTV, 2GD-FTV - -
*a Front view of wire harness connector
(to ECM)
*b Front view of DLC3



b.

Disconnect the connector from the ECM.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 2TR-FE
Tester Connection Condition Condition
G46-19 (TC) - G8-13 (TC) Always Below 1 Ω

for 1KD-FTV, 2KD-FTV
Tester Connection Condition Specified Condition
G84-11 (TC) - G8-13 (TC) Always Below 1 Ω

for 1GD-FTV, 2GD-FTV
Tester Connection Condition Condition
G85-25 (TC) - G8-13 (TC) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (DLC3 - BODY GROUND)
a.
C198509C27
1.458,0.281 1.844,0.51 0.385,0.229 1.635,0.917 2.094,0.531 2.094,0.531 2.24,0.531 true 0.094,0.125 0.313,0.354 0.219,0.229 10 false *a 2.313,0.458 2.594,0.646 0.281,0.188 10 false CG 1.542,0.323 1.833,0.469 0.292,0.146 10 false G8
*a Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G8-4 (CG) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

C335932C01
1.219,0.521 1.615,0.813 0.396,0.292 3.427,0.521 3.823,0.813 0.396,0.292 5.5,0.521 5.896,0.813 0.396,0.292 1.583,2.302 1.396,2.302 1.396,2.302 1.083,1.667 true 3.063,2.323 3.271,2.323 3.271,2.323 3.469,1.573 true 5.615,2.302 5.823,2.302 5.823,2.302 6.031,1.646 true 1.76,0.594 2.073,0.75 0.313,0.156 10 false *A 3.885,0.594 4.198,0.75 0.313,0.156 10 false *B 5.979,0.604 6.292,0.76 0.313,0.156 10 false *C 1.667,2.208 2.063,2.396 0.396,0.188 10 false TC 0.302,0.198 0.615,0.354 0.313,0.156 10 false *a 1.281,0.583 1.729,0.76 0.448,0.177 10 false G46 3.5,0.583 3.948,0.76 0.448,0.177 10 false G84 5.563,0.583 6.01,0.76 0.448,0.177 10 false G85 2.823,2.24 3.219,2.427 0.396,0.188 10 false TC 5.406,2.219 5.802,2.406 0.396,0.188 10 false TC
*A for 2TR-FE *B for 1KD-FTV, 2KD-FTV
*C for 1GD-FTV, 2GD-FTV - -
*a Front view of wire harness connector
(to ECM)
- -


Standard Resistance:
for 2TR-FE
Tester Connection Condition Specified Condition
G46-19 (TC) - Body ground Always Below 1 Ω


for 1KD-FTV, 2KD-FTV
Tester Connection Condition Specified Condition
G84-11 (TC) - Body ground Always Below 1 Ω

for 1GD-FTV, 2GD-FTV
Tester Connection Condition Condition
G85-25 (TC) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR OR EACH ECU