Home › Steering › POWER ASSIST SYSTEMS › VANE PUMP(for 1KD-FTV, 2KD-FTV)
RM33J0E _55 Steering _038482 POWER ASSIST SYSTEMS _0193963 VANE PUMP(for 1KD-FTV, 2KD-FTV) A

POWER ASSIST SYSTEMS  VANE PUMP(for 1KD-FTV, 2KD-FTV)  REASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

When using a vise, place aluminum plates between the part and vise.

·

When using a vise, do not overtighten it.



PROCEDURE

Hide 44341 1.INSTALL FRONT VANE PUMP SIDE PLATE

a.
C330510C01
0,0 0,0 false
V100135

Power Steering Fluid
V113147

Install in this Direction


Coat a new O-ring with power steering fluid.


b.

Install the O-ring to the front housing.


c.
C324308C01
0,0 0,0 false
V100135

Power Steering Fluid
V113147

Install in this Direction


Coat a new O-ring with power steering fluid.


d.

Install the O-ring to the front side plate.


e.
C330511C01
0,0 0,0 false
V113147

Power Steering Fluid


Install the front vane pump side plate to the front housing while aligning the semicircle-shaped cuts of both parts.

NOTICE:

Be sure to install the front vane pump side plate in the correct position and with the correct orientation.



Hide 2.INSTALL VANE PUMP CAM RING

a.
C330512C01
2.354,0.354 2.51,0.271 true 2.563,0.177 2.875,0.375 0.313,0.198 10 false *a
*a Engraved Mark
V113147

Install in this Direction


With the inscribed mark facing upward, install the vane pump cam ring to the front housing while aligning the semicircle-shaped cuts of both parts.

NOTICE:

Be sure to install the vane pump cam ring in the correct position and with the correct orientation.



Hide 3.INSTALL VANE PUMP ROTOR

a.
C330513C01
0,0 0,0 false
V113147

Install in this Direction


Install the vane pump rotor to the front housing.


b.

Install the 10 vane pump plates with the round ends facing outward.

HINT:

The top and bottom of the vane pump rotor are symmetrical.



c.

Coat the 10 vane pump plates with power steering fluid.


d.
C324329C01
0.552,0.604 0.865,0.76 0.313,0.156 10 false *a 1.646,0.073 1.958,0.229 0.313,0.156 10 false *b
*a Outward
*b Inward


Install the 10 vane pump plates.

NOTICE:

Make sure that the round ends of the vane pump plates are facing outward.



Hide 4.INSTALL REAR HOUSING

a.
C330539C01
0,0 0,0 false
V100135

Power Steering Fluid


Coat the vane pump rear housing of the shaft sub-assembly with pulley and the surrounding surface with power steering fluid.


b.
C330540C01
0,0 0,0 false
V100135

Power Steering Fluid
V113147

Install in this Direction


Coat a new O-ring with power steering fluid and install it to the rear housing.


c.
C330514C01
0.969,0.844 1.969,0.271 1.969,0.271 2.646,0.698 true 1.885,0.052 2.198,0.25 0.313,0.198 10 false *a
*a Align


Align the straight pin of the rear housing with the hole created by the semicircle-shaped cuts of the cam ring, front side vane pump plate and front housing.

NOTICE:

Make sure that the O-ring is not out of position before installing the rear housing.



d.
C330508

Install the rear housing with the 4 bolts.

Torque:
22 N*m (224 kgf*cm, 16 ft.*lbf)


Hide 5.INSPECT ROTATING TORQUE

a.
C330515C01
2.646,0.969 2.958,1.167 0.313,0.198 10 false *a
*a Service Bolt


Check that the pump rotates smoothly without abnormal noise.


b.

Temporarily install a bolt to the vane pump shaft.

Recommended Service Bolt:
Item Specified Condition
Thread Diameter 10 mm (0.394 in.)
Thread Pitch 1.25 mm (0.0492 in.)
Bolt Length 50 mm (1.97 in.)



c.

Using a torque wrench, check the power steering vane pump rotating torque.

Standard rotating torque:

0.27 N*m (3 kgf*cm, 2 in.*lbf) or less


If the rotating torque is not as specified, check the installation of the vane pump housing oil seal.


Hide 6.INSTALL FLOW CONTROL VALVE

a.

Coat the flow control valve compression spring and flow control valve with power steering fluid.


b.
C330507

Install the flow control valve compression spring.


c.

Install the flow control valve so that it faces the correct direction.


d.

Coat a new O-ring with power steering fluid and install it to the pressure port union.


e.

Install the pressure port union.

Torque:
69 N*m (704 kgf*cm, 51 ft.*lbf)


Hide 44337 7.INSTALL POWER STEERING SUCTION PORT UNION

a.

Coat a new O-ring with power steering fluid and install it to the power steering suction port union.


b.

Install the power steering suction port union with the bolt.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)