Home › Steering › POWER ASSIST SYSTEMS › VANE PUMP(for TR Series Engine)
RM33J0E _55 Steering _038482 POWER ASSIST SYSTEMS _0193964 VANE PUMP(for 2TR-FE) A

POWER ASSIST SYSTEMS  VANE PUMP(for 2TR-FE)  REASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

When using a vise, place aluminum plates between the part and vise.

·

When using a vise, do not overtighten it.



PROCEDURE

Hide 44302A 1.INSTALL VANE PUMP HOUSING OIL SEAL

a.
C324323N01
0.875,0.958 0.469,0.479 0.469,0.479 0.906,0.688 true 0.198,0.354 0.656,0.552 0.458,0.198 10 false SST

Using SST and a press, press in a new vane pump housing oil seal.

SST
09950-60010  (09951-00280)
09950-70010  (09951-07100)

NOTICE:
·

Make sure to install the vane pump housing oil seal so that it faces the correct direction.

·

Be careful not to damage the vane pump housing oil seal.




b.

Coat the lip of vane pump housing oil seal with MP grease.


Hide 2.INSTALL SHAFT WITH PULLEY

a.
C324324C01
0,0 0,0 false
V100135

Power Steering Fluid


Coat the inside surface of the bushing in the front housing with power steering fluid.


b.
C324325C01
1.76,1.104 1.5,0.667 false 1.323,0.531 1.635,0.729 0.313,0.198 10 false *a
*a Protective Tape


Install the shaft with pulley to the front housing.

NOTICE:
·

Wrap protective tape around the spline of the vane pump shaft with vane pump pulley in order to prevent damage to the oil seal.

·

Be careful not to damage the vane pump housing oil seal.




Hide 44341 3.INSTALL FRONT VANE PUMP SIDE PLATE

a.
C322713C01
0,0 0,0 false
V100135

Power Steering Fluid


Coat a new O-ring with power steering fluid and install it to the front housing.


b.
C324308C01
0,0 0,0 false
V100135

Power Steering Fluid
V113147

Install in this Direction


Coat a new O-ring with power steering fluid and install it to the front vane pump side plate.


c.
C324277C01
0,0 0,0 false
V113147

Install in this Direction


Install the front vane pump side plate to the front housing while aligning the semicircle-shaped cuts of both parts.

NOTICE:

Be sure to install the front vane pump side plate in the correct position and with the correct orientation.



Hide 4.INSTALL VANE PUMP CAM RING

a.
C324327C01
0.792,0.542 0.615,0.427 true 0.469,0.313 0.781,0.469 0.313,0.156 10 false *a
*a Inscribed Mark


With the inscribed mark facing upward, install the vane pump cam ring to the front housing while aligning the semicircle-shaped cuts of both parts.

NOTICE:

Be sure to install the vane pump cam ring in the correct position and with the correct orientation.



Hide 5.INSTALL VANE PUMP ROTOR

a.
C324328C01
0,0 0,0 false
V113147

Install in this Direction


Install the vane pump rotor to the front housing.

HINT:

The top and bottom of the vane pump rotor are symmetrical.



b.
C324329C01
0.552,0.604 0.865,0.76 0.313,0.156 10 false *a 1.646,0.073 1.958,0.229 0.313,0.156 10 false *b
*a Outward
*b Inward


Coat the 10 vane pump plates with power steering fluid.


c.

Install the 10 vane pump plates.

NOTICE:

Make sure that the round ends of the vane pump plates are facing outward.



Hide 6.INSTALL VANE PUMP SHAFT SNAP RING

a.
C324330

Using a screwdriver and snap ring expander, install a new vane pump shaft snap ring to the shaft with pulley.


Hide 7.INSTALL REAR HOUSING

a.

Coat the vane pump rear housing of the shaft sub-assembly with pulley and the surrounding surface with power steering fluid.


b.

Coat a new O-ring with power steering fluid and install it to the rear housing.


c.
C324331C01
0.646,0.979 0.448,1.458 0.448,1.458 1.948,1.167 true 0.25,1.417 0.563,1.615 0.313,0.198 10 false *a
*a Align


Align the straight pin of the rear housing with the hole created by the semicircle-shaped cuts of the vane pump cam ring, front vane pump side plate and front housing.

NOTICE:

Make sure that the O-ring is not out of position before installing the rear housing.



d.

Install the rear housing with the 4 bolts.

Torque:
22 N*m (224 kgf*cm, 16 ft.*lbf)


Hide 8.INSPECT ROTATING TORQUE

a.
C324332C01
0.563,0.75 1.208,1.198 true 0.375,0.635 0.688,0.833 0.313,0.198 10 false *a
*a Service Bolt


Check that the vane pump assembly rotates smoothly without abnormal noise.


b.

Temporarily install the service bolt.

Recommended Service Bolt:
Item Specified Condition
Thread Diameter 10 mm (0.394 in.)
Thread Pitch 1.25 mm (0.0492 in.)
Bolt Length 50 mm (1.97 in.)



c.

Using a torque wrench, check the vane pump rotating torque.

Standard rotating torque:

0.27 N*m (3 kgf*cm, 2 in.*lbf) or less


If the rotating torque is not as specified, check the installation of the vane pump housing oil seal.


Hide 89438 9.INSTALL POWER STEERING OIL PRESSURE SWITCH

a.

Coat the O-ring of the power steering oil pressure switch with power steering fluid.


b.

Install the power steering oil pressure switch to the front housing.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 10.INSTALL FLOW CONTROL VALVE

a.

Coat the flow control valve compression spring and flow control valve with power steering fluid.


b.
C324315

Install the flow control valve compression spring.


c.

Install the flow control valve so that it faces the correct direction.


d.

Coat a new O-ring with power steering fluid and install it to the pressure port union.


e.

Install the pressure port union.

Torque:
69 N*m (704 kgf*cm, 51 ft.*lbf)


Hide 44306 11.INSTALL VANE PUMP OIL RESERVOIR SUB-ASSEMBLY

a.

Coat a new O-ring with power steering fluid, and install it to the vane pump oil reservoir sub-assembly.


b.

Install the vane pump oil reservoir sub-assembly to the vane pump with the 3 bolts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 44305 12.INSTALL VANE PUMP OIL RESERVOIR CAP SUB-ASSEMBLY