Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY
RM33J0E _55 Steering _038483 STEERING COLUMN _0193966 STEERING COLUMN ASSEMBLY A

STEERING COLUMN  STEERING COLUMN ASSEMBLY  DISASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

When using a vise, place aluminum plates between the part and vise.

·

When using a vise, do not overtighten it.



PROCEDURE

Hide 45206A 1.REMOVE STEERING SLIDING WITH COUPLING YOKE SUB-ASSEMBLY

a.
C322176C01
1.656,1.063 0.896,0.615 0.896,0.615 1.771,1.021 true 0.677,0.51 0.99,0.708 0.313,0.198 10 false *a
*a Matchmark


Place matchmarks on the steering main shaft and steering sliding with coupling yoke sub-assembly.


b.

Remove the bolt and steering sliding with coupling yoke sub-assembly.


Hide 89782 2.REMOVE TRANSPONDER KEY COIL (w/ Engine Immobiliser System)

Hide 45020B 3.REMOVE STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY

a.

Using a 3 mm pin punch, mark the center of the tapered-head bolt.


b.

Using a 3 to 4 mm drill bit, drill into the tapered-head bolt.


c.
C322177C01
2.135,1.073 2.531,1.365 false 2.625,1.323 2.938,1.479 0.313,0.156 10 false *a
*a Screw Extractor


Using a screw extractor, remove the bolt and steering column upper with switch bracket.


Hide 69057A 4.REMOVE IGNITION SWITCH LOCK CYLINDER ASSEMBLY

a.
C324269C01
2.104,0.396 2.292,0.635 true 1.969,0.302 2.125,0.458 0.156,0.156 10 false *1 0.646,0.208 0.958,0.365 0.313,0.156 10 false *a 1.646,2.76 1.958,2.917 0.313,0.156 10 false *b 2.948,1.896 3.26,2.052 0.313,0.156 10 false *b
*1 ACC
*a Push
*b Pull


Turn the ignition switch to ACC.


b.

Insert the tip of a screwdriver into the hole in the steering column upper bracket as shown in the illustration, and pull the ignition switch lock cylinder out until its claw comes into contact with the stopper of the steering column upper bracket.

NOTICE:

Pull the ignition switch lock cylinder assembly out until its claw comes into contact with the stopper of the steering column upper bracket assembly. Otherwise, the following procedure cannot be conducted properly.



c.
C324270C01
0.469,0.667 0.667,1.302 0.667,1.302 0.833,1.302 true 0.25,0.333 0.333,0.333 0.333,0.333 0.396,0.583 true 0.865,1.219 1.177,1.375 0.313,0.156 10 false *1 0.104,0.26 0.417,0.417 0.313,0.156 10 false *2 1.719,3.125 2.031,3.281 0.313,0.156 10 false *a 2.146,0.271 2.458,0.427 0.313,0.156 10 false *b 2.583,3.115 2.896,3.271 0.313,0.156 10 false *c
*1 Stopper
*2 Claw
*a Tilt
*b Claw is detached
*c Pull out


Insert the tip of a screwdriver into the hole in the steering column bracket and tilt it downward as shown in the illustration to detach the claw of the ignition switch lock cylinder. Then pull out the ignition switch lock cylinder.


Hide 84052 5.REMOVE UN-LOCK WARNING SWITCH ASSEMBLY

Hide 84450 6.REMOVE IGNITION OR STARTER SWITCH ASSEMBLY

Hide 85432 7.REMOVE KEY INTERLOCK SOLENOID (for Automatic Transmission)

a.
C324271

Remove the screw and key interlock solenoid from the steering column upper with switch bracket.


Hide 45020B 8.REMOVE STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY (for Smart Entry and Start System)

a.

Using a center punch, mark the center of the tapered-head bolt.


b.

Using a 3 to 4 mm (0.119 to 0.157 in.) drill, drill a hole in the bolt.


c.
C322180

Using a screw extractor, remove the bolt and steering lock actuator assembly from the steering column sub-assembly.