Home › Steering › STEERING COLUMN › STEERING PAD SWITCH
RM33J0E _55 Steering _038483 STEERING COLUMN _0193968 STEERING PAD SWITCH G

STEERING COLUMN  STEERING PAD SWITCH  INSPECTION  


PROCEDURE

Hide 84250A 1.INSPECT STEERING PAD SWITCH ASSEMBLY (w/o Multi-information Display)

a.

Measure the resistance according to the value(s) in the table below.

C322173C01
3.063,0.469 3.292,0.667 true 3.156,1.073 3.406,0.865 true 3.896,1.198 3.635,0.865 true 4,1.052 3.76,0.865 true 4.063,0.479 3.771,0.656 true 1.771,1.542 1.438,1.052 true 2.052,1.531 1.792,0.844 true 1.448,1.615 1.073,1.448 true 1.448,1.885 1.063,2.063 true 1.667,2.24 1.385,2.49 true 1.969,2.26 1.729,2.75 true 1.708,1.927 1.104,2.406 true 1.333,2.906 2.042,1.948 true 2.854,1.01 3.313,1.208 0.458,0.198 10 false EAU 2.844,0.375 3.302,0.573 0.458,0.198 10 false HO 3.833,1.229 4.292,1.427 0.458,0.198 10 false AU2 4.042,0.99 4.5,1.188 0.458,0.198 10 false AU1 4.094,0.375 4.552,0.573 0.458,0.198 10 false IL+2 2.667,1.677 3.125,1.875 0.458,0.198 10 false *9 0.906,1.333 1.219,1.49 0.313,0.156 10 false *1 0.885,1.979 1.198,2.135 0.313,0.156 10 false *2 1.281,0.927 1.594,1.083 0.313,0.156 10 false *3 0.927,2.396 1.24,2.552 0.313,0.156 10 false *4 1.646,0.677 1.958,0.833 0.313,0.156 10 false *5 1.542,2.75 1.854,2.906 0.313,0.156 10 false *6 1.219,2.479 1.531,2.635 0.313,0.156 10 false *7 1.177,2.875 1.49,3.031 0.313,0.156 10 false *8
*1 Volume+ Switch *2 Volume- Switch
*3 Seek+ Switch *4 Seek- Switch
*5 MODE Switch *6 On Hook Switch
*7 Off Hook Switch *8 Voice Switch
*9 Horn Wire - -


Standard Resistance:
Tester Connection Switch Condition Specified Condition
10 (AU2) - 8 (EAU) No switch pushed 95 to 105 kΩ
10 (AU2) - 8 (EAU) MODE switch pushed Below 2.5 Ω
10 (AU2) - 8 (EAU) Voice switch pushed 2954.5 to 3265.5 Ω
10 (AU2) - 8 (EAU) Off hook switch pushed 950 to 1050 Ω
10 (AU2) - 8 (EAU) On hook switch pushed 312.6 to 345.5 Ω
11 (AU1) - 8 (EAU) No switch pushed 95 to 105 kΩ
11 (AU1) - 8 (EAU) Volume+ switch pushed 950 to 1050 Ω
11 (AU1) - 8 (EAU) Volume- switch pushed 2954.5 to 3265.5 Ω
11 (AU1) - 8 (EAU) Seek+ switch pushed Below 2.5 Ω
11 (AU1) - 8 (EAU) Seek- switch pushed 312.6 to 345.5 Ω
1 (HO) - Horn Wire Always Below 2.5 Ω


If the result is not as specified, replace the steering pad switch assembly.


b.

Check the switch illumination.

i.

Connect the battery positive (+) lead to terminal IL+2 and the negative (-) lead to terminal EAU of the steering pad switch assembly connector.


ii.

Check that the switch illumination comes on.

OK:

Steering pad switch illumination comes on.


If the result is not as specified, replace the steering pad switch assembly.



Hide 84250A 2.INSPECT STEERING PAD SWITCH ASSEMBLY (w/ Multi-information Display)

a.

Type A:

i.

Measure the resistance according to the value(s) in the table below.

C322174C01
1,2.073 1.427,1.885 true 1.188,2.656 1.604,2.24 true 1.792,2.885 2,2.271 true 2.021,1.531 1.74,0.781 true 1.76,1.542 1.375,0.958 true 1.438,1.604 1.042,1.333 true 1.063,2.344 1.76,1.938 true 5.771,2.75 5.333,2.26 true 3.281,0.667 3.01,0.448 true 3.406,0.646 3.115,0.281 true 3.75,0.646 4.01,0.313 true 3.865,1.156 3.635,0.865 true 4.083,1.083 3.76,0.854 true 3.219,1.188 3.417,0.865 true 1.375,2.938 2.031,1.948 true 3.969,0.146 4.344,0.344 0.375,0.198 10 false IL+2 2.865,0.135 3.24,0.333 0.375,0.198 10 false +DP 2.781,0.365 3.156,0.563 0.375,0.198 10 false HO 2.99,1.198 3.365,1.396 0.375,0.198 10 false EAU 3.813,1.177 4.188,1.375 0.375,0.198 10 false AU2 4.115,1.01 4.49,1.208 0.375,0.198 10 false AU1 0.854,1.229 1.167,1.385 0.313,0.156 10 false *1 0.823,2.01 1.135,2.167 0.313,0.156 10 false *2 1.24,0.823 1.552,0.979 0.313,0.156 10 false *3 0.865,2.302 1.177,2.458 0.313,0.156 10 false *4 1.625,0.615 1.938,0.771 0.313,0.156 10 false *5 1.635,2.917 1.948,3.073 0.313,0.156 10 false *6 1.01,2.615 1.323,2.771 0.313,0.156 10 false *7 5.854,2.76 6.167,2.917 0.313,0.156 10 false *9 1.208,2.938 1.521,3.094 0.313,0.156 10 false *8 2.677,1.677 2.99,1.833 0.313,0.156 10 false *10
*1 Volume+ Switch *2 Volume- Switch
*3 Seek+ Switch *4 Seek- Switch
*5 MODE Switch *6 On Hook Switch
*7 Off Hook Switch *8 Voice Switch
*9 DISP Switch *10 Horn Wire


Standard Resistance:
Tester Connection Switch Condition Specified Condition
10 (AU2) - 8 (EAU) No switch pushed 95 to 105 kΩ
10 (AU2) - 8 (EAU) MODE switch pushed Below 2.5 Ω
10 (AU2) - 8 (EAU) Voice switch pushed 2954.5 to 3265.5 Ω
10 (AU2) - 8 (EAU) Off hook switch pushed 950 to 1050 Ω
10 (AU2) - 8 (EAU) On hook switch pushed 312.6 to 345.5 Ω
11 (AU1) - 8 (EAU) No switch pushed 95 to 105 kΩ
11 (AU1) - 8 (EAU) Volume+ switch pushed 950 to 1050 Ω
11 (AU1) - 8 (EAU) Volume- switch pushed 2954.5 to 3265.5 Ω
11 (AU1) - 8 (EAU) Seek+ switch pushed Below 2.5 Ω
11 (AU1) - 8 (EAU) Seek- switch pushed 312.6 to 345.5 Ω
2 (+DP) - 8 (EAU) DISP switch pushed Below 2.5 Ω
1 (HO) - Horn Wire Always Below 2.5 Ω


If the result is not as specified, replace the steering pad switch assembly.



b.

Type B:

i.

Measure the resistance according to the value(s) in the table below.

C322175C01
1.198,2.74 1.583,2.354 true 1.813,3.052 2,2.396 true 5.229,1.646 5.417,0.938 true 5.698,2.604 5.26,2.083 true 6.167,2.24 5.729,2.01 true 2.052,1.656 1.813,0.979 true 1.74,1.677 1.427,1.135 true 1.438,1.698 1.073,1.406 true 1.448,2.042 1.01,2.25 true 1.76,2.073 1.094,2.5 true 5.26,2.771 5.063,1.938 true 6.208,1.479 5.74,1.75 true 5.927,1.208 5.438,1.823 true 3.406,0.813 3.115,0.469 true 3.292,0.833 3.021,0.698 true 3.531,0.813 3.302,0.313 true 3.792,0.813 4.063,0.385 true 4,1.438 3.635,1.021 true 4.135,1.313 3.771,1 true 3.167,1.344 3.417,1.021 true 5.688,1.052 5.26,1.844 true 1.448,2.958 2.031,2.083 true 4.115,0.271 4.51,0.448 0.396,0.177 10 false IL+2 4.167,1.25 4.563,1.427 0.396,0.177 10 false AU1 3.917,1.458 4.313,1.635 0.396,0.177 10 false AU2 2.948,1.365 3.344,1.542 0.396,0.177 10 false EAU 2.792,0.604 3.188,0.781 0.396,0.177 10 false HO 2.844,0.333 3.24,0.51 0.396,0.177 10 false +DP 3.083,0.135 3.479,0.313 0.396,0.177 10 false +DP2 0.906,1.292 1.219,1.448 0.313,0.156 10 false *1 0.844,2.188 1.156,2.344 0.313,0.156 10 false *2 1.281,0.969 1.594,1.125 0.313,0.156 10 false *3 0.927,2.427 1.24,2.583 0.313,0.156 10 false *4 1.698,0.833 2.01,0.99 0.313,0.156 10 false *5 1.719,3.094 2.031,3.25 0.313,0.156 10 false *6 1.042,2.698 1.354,2.854 0.313,0.156 10 false *7 1.292,2.948 1.604,3.104 0.313,0.156 10 false *8 5.354,0.74 5.667,0.896 0.313,0.156 10 false *9 2.677,1.823 3.146,1.979 0.469,0.156 10 false *16 5.75,2.604 6.219,2.76 0.469,0.156 10 false *10 5.177,2.833 5.646,2.99 0.469,0.156 10 false *11 5.885,1.063 6.354,1.219 0.469,0.156 10 false *12 5.625,0.854 6.094,1.01 0.469,0.156 10 false *13 6.24,1.406 6.708,1.563 0.469,0.156 10 false *14 6.219,2.188 6.688,2.344 0.469,0.156 10 false *15
*1 Volume+ Switch *2 Volume- Switch
*3 Seek+ Switch *4 Seek- Switch
*5 MODE Switch *6 On Hook Switch
*7 Off Hook Switch *8 Voice Switch
*9 UP *10 DOWN
*11 LEFT *12 RIGHT
*13 ENTER Switch *14 BACK Switch
*15 TOP Switch *16 Horn Wire


Standard Resistance:
Tester Connection Switch Condition Specified Condition
10 (AU2) - 8 (EAU) No switch pushed 95 to 105 kΩ
10 (AU2) - 8 (EAU) MODE switch pushed Below 2.5 Ω
10 (AU2) - 8 (EAU) Voice switch pushed 2954.5 to 3265.5 Ω
10 (AU2) - 8 (EAU) Off hook switch pushed 950 to 1050 Ω
10 (AU2) - 8 (EAU) On hook switch pushed 312.6 to 345.5 Ω
11 (AU1) - 8 (EAU) No switch pushed 95 to 105 kΩ
11 (AU1) - 8 (EAU) Volume+ switch pushed 950 to 1050 Ω
11 (AU1) - 8 (EAU) Volume- switch pushed 2954.5 to 3265.5 Ω
11 (AU1) - 8 (EAU) Seek+ switch pushed Below 2.5 Ω
11 (AU1) - 8 (EAU) Seek- switch pushed 312.6 to 345.5 Ω
3 (+DP2) - 8 (EAU) No switch pushed 95 to 105 kΩ
3 (+DP2) - 8 (EAU) UP 312.6 to 345.5 Ω
3 (+DP2) - 8 (EAU) DOWN 950 to 1050 Ω
3 (+DP2) - 8 (EAU) LEFT Below 2.5 Ω
3 (+DP2) - 8 (EAU) RIGHT 2954.5 to 3265.5 Ω
2 (+DP) - 8 (EAU) No switch pushed 95 to 105 kΩ
2 (+DP) - 8 (EAU) ENTER switch pushed Below 2.5 Ω
2 (+DP) - 8 (EAU) BACK switch pushed 950 to 1050 Ω
2 (+DP) - 8 (EAU) TOP switch pushed 312.6 to 345.5 Ω
1 (HO) - Horn Wire Always Below 2.5 Ω


If the result is not as specified, replace the steering pad switch assembly.



c.

Check the switch illumination.

i.

Connect the battery positive (+) lead to terminal IL+2 and the negative (-) lead to terminal EAU of the steering pad switch assembly connector.


ii.

Check that the switch illumination comes on.

OK:

Steering pad switch illumination comes on.


If the result is not as specified, replace the steering pad switch assembly.