Home › Drivetrain › CLUTCH › CLUTCH UNIT(for R151)
RM33J0E _52 Drivetrain _038465 CLUTCH _0193976 CLUTCH UNIT(for R151) A

CLUTCH  CLUTCH UNIT(for R151)  INSTALLATION  


PROCEDURE

Hide 31250 1.INSTALL CLUTCH DISC ASSEMBLY

C226320C02
1.75,1.396 1.5,1.104 false 1.688,1.438 2.146,1.635 0.458,0.198 10 false SST 2.229,0.729 2.542,0.885 0.313,0.156 10 false *a
*a Flywheel side


a.

Insert SST into the clutch disc assembly. Then insert SST (together with the clutch disc) into the flywheel.

SST
09301-00110  

NOTICE:

Be sure to install the clutch disc so that it is facing in the correct direction.



Hide 31210 2.INSTALL CLUTCH COVER ASSEMBLY

a.
C322151C01
1.177,1.479 1.063,1.948 1.063,1.948 1.094,1.542 true 2.344,0.667 2.802,0.833 true 0.938,1.938 1.25,2.135 0.313,0.198 10 false *a 2,0.198 2.156,0.396 0.156,0.198 10 false 1 0.542,1.177 0.698,1.375 0.156,0.198 10 false 2 2.583,1.781 2.74,1.979 0.156,0.198 10 false 3 0.854,0.073 1.01,0.271 0.156,0.198 10 false 4 1.156,1.979 1.354,2.156 0.198,0.177 10 false 5 2.635,1.083 2.833,1.26 0.198,0.177 10 false 6 2.875,0.781 3.26,1.021 0.385,0.24 10 false SST
*a Matchmark


Align the matchmarks on the clutch cover assembly and flywheel.


b.

Tighten the 6 bolts as described below.

i.

Determine the first bolt to be tightened by choosing the bolt closest to the knock pin.


ii.

Uniformly tighten the 6 bolts in diametrically opposite pairs relative to the position of the first bolt. Use the illustration as a reference.



c.

Lightly move SST up and down, and right and left.

SST
09301-00110  


d.

Check that the disc is in the center, and then tighten the bolts.

Torque:
19.1 N*m (195 kgf*cm, 14 ft.*lbf)


Hide 31210 3.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY

a.
C322152

Using a dial indicator with a roller instrument, measure the diaphragm spring tip alignment.

Maximum misalignment:

0.5 mm (0.020 in.)


C322153N01
2.51,1.76 1.906,0.802 true 2.49,1.844 2.948,2.042 0.458,0.198 10 false SST

If the misalignment is more than the maximum, use SST to adjust the diaphragm spring tip alignment.


SST
09333-00013  


Hide 31236B 4.INSTALL RELEASE FORK SUPPORT

a.

Install the release fork support to the manual transmission unit.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)


Hide 31237 5.INSTALL CLUTCH RELEASE FORK SUPPORT BOOT (for TR Engine)

a.

Install the clutch release fork support boot to the clutch release fork sub-assembly.


b.

Install the release fork support spring to the clutch release fork sub-assembly.


Hide 31241 6.INSTALL CLUTCH RELEASE FORK DUST SEAL (for KD Engine)

a.

Install the clutch release fork dust seal to the clutch release fork sub-assembly.


b.

Install the clutch release fork collar to the clutch release fork sub-assembly.


Hide 31230 7.INSTALL CLUTCH RELEASE BEARING ASSEMBLY

a.
C327838C01
0,0 0,0 false
V100135

Multemp 8158 grease or equivalent


Apply grease to the clutch release bearing assembly.

Grease:

Multemp 8158 grease or equivalent


Amount of Grease:

0.3 to 0.5 g (0.011 to 0.018 oz)


HINT:

When replacing the clutch release bearing assembly with a new one, do not apply grease.



b.

Install the release bearing hub clip to the clutch release bearing assembly.


c.
C322142C02
0.177,0.198 0.49,0.396 0.313,0.198 10 false *A 0.198,2.24 0.51,2.438 0.313,0.198 10 false *B 0.667,0.406 0.979,0.604 0.313,0.198 10 false *a 1.75,1.354 2.063,1.552 0.313,0.198 10 false *c 2.365,0.552 2.677,0.75 0.313,0.198 10 false *b 1.083,0.24 1.396,0.438 0.313,0.198 10 false *a 0.719,2.365 1.031,2.563 0.313,0.198 10 false *a 1.083,2.25 1.396,2.448 0.313,0.198 10 false *a 2.438,2.521 2.75,2.719 0.313,0.198 10 false *b 1.771,3.406 2.083,3.604 0.313,0.198 10 false *c
*A for TR Engine
*B for KD Engine
*a The surfaces of the release fork that contact the release bearing
*b The surfaces of the release fork that contact the release fork support
*c The surfaces of the release fork that contact the push rod of the release cylinder
V100135

Multemp 8158 grease or equivalent


Apply grease or equivalent to the following areas.

Grease:

Multemp 8158 grease or equivalent


Amount of Grease:
The surfaces of the release fork that contact the release bearing 1.0 to 1.3 g (0.04 to 0.05 oz)
The surfaces of the release fork that contact the release fork support 1.3 to 1.8 g (0.05 to 0.06 oz)
The surfaces of the release fork that contact the push rod of the release cylinder 0.5 to 0.9 g (0.02 to 0.03 oz)



d.

Install the release fork sub-assembly to the clutch release bearing assembly.


e.

Install the clutch release bearing assembly together with the clutch release fork sub-assembly to the clutch housing.

NOTICE:

After the installation, move the fork forward and backward to check that the release bearing slides smoothly.



f.
C324337C01
1.667,3.344 2.083,2.927 true 1.719,1.104 2.135,0.688 true 0.083,0.125 0.417,0.438 0.333,0.313 10 true *A 0.125,2.469 0.385,2.708 0.26,0.24 10 true *B 2.167,0.573 2.375,0.823 0.208,0.25 10 true *a 2.115,2.802 2.375,3.021 0.26,0.219 10 true *a
*A for TR Engine
*B for KD Engine
*a Contact surface of the bearing
V100135

Toyota Genuine Clutch Spline Grease or equivalent


Apply the clutch spline grease to the spline of the input shaft.

Grease:

Toyota Genuine Clutch Spline Grease or equivalent


NOTICE:

Make sure that no grease adheres to the contact surface of the bearing.



Hide 31126 8.INSTALL CLUTCH RELEASE FORK BOOT