Home › Brake › BRAKE (FRONT) › FRONT BRAKE(for 4WD and Pre-Runner)
RM33J0E _54 Brake _038479 BRAKE (FRONT) _0193990 FRONT BRAKE(for 4WD and Pre-Runner) A

BRAKE (FRONT)  FRONT BRAKE(for 4WD and Pre-Runner)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 43512 1.INSTALL FRONT DISC

a.
C321911C01
1.719,1.208 1.708,0.854 1.708,0.854 2.833,0.854 true 1.729,1.292 2.375,1.292 2.375,1.292 2.375,0.865 true 2.927,0.781 3.125,0.948 0.198,0.167 10 false *a
*a Matchmark


Align the matchmarks and install the front disc.

HINT:

When replacing the disc with a new one, select the installation position where the front disc has the smallest runout.



Hide 47750 2.INSTALL DISC BRAKE CYLINDER ASSEMBLY LH

a.

Install the disc brake cylinder assembly LH with the 2 bolts.

Torque:
197 N*m (2009 kgf*cm, 145 ft.*lbf)


Hide 47343A 3.CONNECT FRONT NO. 1 WHEEL CYLINDER TUBE LH

a.
A329093C03
1.719,0.542 2.031,0.698 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a union nut wrench, connect the front No. 1 wheel cylinder tube LH to the disc brake cylinder assembly LH.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.8661 in.)) + torque wrench (fulcrum length of 162 mm (6.3779 in.)): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)




Hide 04945 4.INSTALL FRONT ANTI-SQUEAL SHIM KIT

C321920C01
0.219,0.552 0.219,0.25 0.219,0.25 0.594,0.25 false 0.906,1.729 0.906,2.333 false 2.594,2.698 2.594,3.052 false 3.063,2.208 3.063,1.302 3.063,1.302 2.813,1.302 false 1.365,1.198 1.365,0.594 1.365,0.594 2.094,0.594 false 1.854,1.521 1.854,0.594 false 0.844,2.396 1.156,2.552 0.313,0.156 10 false *2 2.531,3.083 2.729,3.24 0.198,0.156 10 false *2 2.167,0.531 2.354,0.688 0.188,0.156 10 false *1 0.635,0.188 0.833,0.344 0.198,0.156 10 false *3 2.583,1.25 2.781,1.406 0.198,0.156 10 false *3
*1 Front Disc Brake Pad
*2 No. 1 Anti-squeal Shim
*3 No. 2 Anti-squeal Shim
V100135

Disc brake grease


a.

except 16 inch Front Disc Brake (Type B):

i.

Apply disc brake grease to both sides of each No. 1 anti-squeal shim.

NOTICE:

For 16 inch Front Disc Brake (Type B), do not apply disc brake grease.




b.

Install the No. 1 anti-squeal shims and No. 2 anti-squeal shims to each pad.

NOTICE:
·

When replacing worn front disc brake pads, the anti-squeal shims must be replaced together with the front disc brake pads.

·

Install the anti-squeal shims in the correct positions and directions as shown in the illustration.




Hide 04465 5.INSTALL DISC BRAKE PAD KIT FRONT

a.

Install the 2 front disc brake pads to the disc brake cylinder assembly LH.

NOTICE:

Make sure there is no oil or grease on the friction surface of the front disc brake pads and front disc.



Hide 04947 6.INSTALL FRONT DISC BRAKE ANTI-RATTLE SPRING

a.

for 15 inch Front Disc Brake (Type A):

i.

Install the 2 disc brake pad guide pins and front disc brake anti-rattle spring.

HINT:

Install the front disc brake anti-rattle spring together with the disc brake pad guide pin on the bottom side.



ii.

Install the pin hold clip.



b.

for 15 inch Front Disc Brake (Type B):

i.

Install the front disc brake anti-rattle spring.


ii.

Hold down the front disc brake anti-rattle spring and insert the 2 disc brake pad guide pins.


iii.

Install the pin hold clip.



c.

for 16 inch Front Disc Brake (Type A):

i.

Install the 2 disc brake pad guide pins and front disc brake anti-rattle spring.

HINT:

Install the front disc brake anti-rattle spring together with the disc brake pad guide pin on the bottom side.



ii.

Install the 2 pin hold clips.

NOTICE:

When installing the pin hold clip, be sure to install the pin hold clip with the handle facing the center of the vehicle.




d.

for 16 inch Front Disc Brake (Type B):

i.

Install the front disc brake anti-rattle spring.


ii.

Hold down the front disc brake anti-rattle spring and insert the 2 disc brake pad guide pins.


iii.

Install the 2 clips.

NOTICE:

When installing the pin hold clip, be sure to install the pin hold clip with the handle facing the center of the vehicle.




Hide 7.BLEED BRAKE LINE (w/ VSC)

Hide 8.BLEED BRAKE LINE (w/o VSC)

Hide 9.BLEED CLUTCH LINE (for Manual Transmission)

Hide 10.INSTALL FRONT WHEEL