Home › Brake › BRAKE (FRONT) › FRONT BRAKE(for 16 inch Front Disc Brake 2WD)
RM33J0E _54 Brake _038479 BRAKE (FRONT) _0193992 FRONT BRAKE(for 16 inch Front Disc Brake 2WD) A

BRAKE (FRONT)  FRONT BRAKE(for 16 inch Front Disc Brake 2WD)  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.REMOVE FRONT WHEEL

Hide 2.DRAIN BRAKE FLUID

NOTICE:

Wash off brake fluid immediately if it comes in contact with any painted surface.


Hide 47313A 3.DISCONNECT FRONT FLEXIBLE HOSE

a.
C321895

Remove the union bolt and gasket.


b.

Disconnect the front flexible hose from the disc brake cylinder assembly LH.


Hide 47750 4.REMOVE DISC BRAKE CYLINDER ASSEMBLY LH

a.
C321904C01
1.979,2.135 2.104,2.01 2.104,2.01 2.26,2.01 true 1.333,2.125 0.958,2.406 0.958,2.406 0.74,2.406 true 0.542,2.323 0.74,2.521 0.198,0.198 10 false *a 2.271,1.927 2.469,2.094 0.198,0.167 10 true *b
*a Hold
*b Turn


Hold the front disc brake cylinder slide pin and remove the 2 bolts and disc brake cylinder assembly LH.


Hide 04465 5.REMOVE FRONT DISC BRAKE PAD

a.
C321897

Remove the 2 anti-squeal springs from the front disc brake pads.


b.

Remove the 2 front disc brake pads from the front disc brake cylinder mounting LH.


Hide 04945 6.REMOVE FRONT ANTI-SQUEAL SHIM KIT

a.

Remove the 2 No. 1 anti-squeal shims from each pad.


Hide 7.REMOVE PAD WEAR INDICATOR PLATE

a.
C306284

Using a screwdriver, remove the pad wear indicator plates from the front disc brake pads as shown in the illustration.


Hide 8.REMOVE NO. 1 PAD SUPPORT PLATE

a.
C321870C01
1.479,0.49 1.479,0.615 1.479,0.615 0.875,0.615 true 1.333,1.563 1.333,1.344 1.333,1.344 0.677,1.344 true 2.073,0.479 2.396,0.479 true 1.906,1.792 2.333,1.792 true 0.677,0.542 0.865,0.729 0.188,0.188 10 false *1 0.469,1.281 0.656,1.458 0.188,0.177 10 false *2 2.354,1.698 2.542,1.885 0.188,0.188 10 true *1 2.417,0.385 2.604,0.563 0.188,0.177 10 true *2
*1 No. 1 Pad Support Plate
*2 No. 2 Pad Support Plate


Remove the 2 No. 1 pad support plates from the front disc brake cylinder mounting LH.

NOTICE:

Each pad support plate has a different shape. Be sure to put an identification mark on each pad support plate so that they can be reinstalled to their original positions.



Hide 9.REMOVE NO. 2 PAD SUPPORT PLATE

a.

Remove the 2 No. 2 pad support plates from the front disc brake cylinder mounting LH.

NOTICE:

Each pad support plate has a different shape. Be sure to put an identification mark on each pad support plate so that they can be reinstalled to their original positions.



Hide 47722 10.REMOVE FRONT DISC BRAKE CYLINDER MOUNTING LH

a.
C321871

Remove the 2 bolts and front disc brake cylinder mounting LH.


Hide 11.REMOVE FRONT DISC BRAKE CYLINDER SLIDE PIN

a.
C321872

Remove the front disc brake cylinder slide pin from the front disc brake cylinder mounting LH.


Hide 12.REMOVE NO. 2 FRONT DISC BRAKE CYLINDER SLIDE PIN

a.
C321873

Remove the No. 2 front disc brake cylinder slide pin from the front disc brake cylinder mounting LH.


Hide 13.REMOVE FRONT DISC BRAKE CYLINDER SLIDE BUSH

a.
C321874C01
2.073,1.552 2.313,0.906 2.313,0.906 2.583,0.906 false 2.625,0.813 2.833,1.01 0.208,0.198 10 false *a
*a Protective Tape


Using a screwdriver, remove the front disc brake cylinder slide bush from the No. 2 front disc brake cylinder slide pin.

HINT:

Tape the screwdriver tip before use.


NOTICE:

Be careful not to damage the pin.



Hide 14.REMOVE FRONT DISC BRAKE BUSH DUST BOOT

a.
C321875

Remove the 2 front disc brake bush dust boots from the front disc brake cylinder mounting LH.


Hide 43512 15.REMOVE FRONT DISC

a.
C321876C01
1.708,1.271 1.698,1.094 1.698,1.094 2.865,1.094 true 1.719,1.333 2.385,1.333 2.385,1.333 2.385,1.104 true 2.938,1.01 3.25,1.167 0.313,0.156 10 false *a
*a Matchmark


Put matchmarks on the front disc and axle hub.


b.

Remove the front disc.