Home › Brake › BRAKE (FRONT) › FRONT BRAKE(for 16 inch Front Disc Brake 2WD)
RM33J0E _54 Brake _038479 BRAKE (FRONT) _0193992 FRONT BRAKE(for 16 inch Front Disc Brake 2WD) A

BRAKE (FRONT)  FRONT BRAKE(for 16 inch Front Disc Brake 2WD)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 43512 1.INSTALL FRONT DISC

a.
C321876C01
1.708,1.271 1.698,1.094 1.698,1.094 2.865,1.094 true 1.719,1.333 2.385,1.333 2.385,1.333 2.385,1.104 true 2.938,1.01 3.25,1.167 0.313,0.156 10 false *a
*a Matchmark


Align the matchmarks and install the front disc.

HINT:

When replacing the front disc with a new one, select the installation position where the front disc has the smallest runout.



Hide 2.INSTALL FRONT DISC BRAKE BUSH DUST BOOT

a.
C321886C01
0,0 0,0 false
V100155

Lithium soap base glycol grease


Apply a light coat of lithium soap base glycol grease to the entire circumference of a new front disc brake bush dust boot, and the entire inner circumference of both ends.

HINT:

Apply at least 0.3 g (0.01 oz.) of lithium soap base glycol grease to the front disc brake bush dust boot.


NOTICE:

Apply a sufficient amount of lithium soap base glycol grease to the entire circumference of the front disc brake bush dust boot and front disc brake cylinder mounting LH contact surfaces.



b.

Install the 2 front disc brake bush dust boots to the front disc brake cylinder mounting LH.


Hide 3.INSTALL FRONT DISC BRAKE CYLINDER SLIDE BUSH

a.
C321887C01
0,0 0,0 false
V100155

Lithium soap base glycol grease


Apply a light coat of lithium soap base glycol grease to the contact surface of the No. 2 front disc brake cylinder slide pin where it contacts the front disc brake cylinder slide bush.


b.

Install a new front disc brake cylinder slide bush to the No. 2 front disc brake cylinder slide pin.


Hide 4.INSTALL FRONT DISC BRAKE CYLINDER SLIDE PIN

a.
C321889C01
0,0 0,0 false
V100155

Lithium soap base glycol grease


Apply a light coat of lithium soap base glycol grease to the sliding part and the seal surface of the front disc brake cylinder slide pin.


b.

Install the front disc brake cylinder slide pin to the front disc brake cylinder mounting LH.


c.

Push the front disc brake cylinder slide pin into the front disc brake bush dust boot to align them.


Hide 5.INSTALL NO. 2 FRONT DISC BRAKE CYLINDER SLIDE PIN

a.
C321888C01
0,0 0,0 false
V100155

Lithium soap base glycol grease


Apply a light coat of lithium soap base glycol grease to the sliding part and the seal surface of the No. 2 disc brake cylinder slide pin.


b.

Install the No. 2 disc brake cylinder slide pin to the front disc brake cylinder mounting LH.


c.

Push the No. 2 disc brake cylinder slide pin into the front disc brake bush dust boot to align them.


Hide 47722 6.INSTALL FRONT DISC BRAKE CYLINDER MOUNTING LH

a.

Install the front disc brake cylinder mounting LH with the 2 bolts.

Torque:
160 N*m (1632 kgf*cm, 118 ft.*lbf)


Hide 7.INSTALL NO. 1 PAD SUPPORT PLATE

a.
C321891C01
0.823,0.833 0.635,0.833 false 2.625,0.833 2.833,0.833 false 0.813,3.813 0.615,3.813 false 2.625,3.813 2.813,3.813 false 0.427,0.771 0.625,0.938 0.198,0.167 10 false *1 2.885,0.76 3.063,0.927 0.177,0.167 10 false *2 0.417,3.75 0.594,3.917 0.177,0.167 10 false *2 2.865,3.75 3.063,3.917 0.198,0.167 10 false *1
*1 No. 1 Pad Support Plate
*2 No. 2 Pad Support Plate


Install the 2 No. 1 pad support plates to the front disc brake cylinder mounting LH.

NOTICE:
·

The shapes of the pad support plates differ. Therefore, when replacing a pad support plate with a new plate, make sure to check the part number and shape for the installation position prior to installation.

·

When reusing a pad support plate, make sure to check the installation position using the matchmark placed during removal prior to installation.




Hide 8.INSTALL NO. 2 PAD SUPPORT PLATE

a.

Install the 2 No. 2 pad support plates to the front disc brake cylinder mounting LH.

NOTICE:
·

The shapes of the pad support plates differ. Therefore, when replacing a pad support plate with a new plate, make sure to check the part number and shape for the installation position prior to installation.

·

When reusing a pad support plate, make sure to check the installation position using the matchmark placed during removal prior to installation.




Hide 9.INSTALL PAD WEAR INDICATOR PLATE

a.

Install the pad wear indicator plate to the inner lower side of the front disc brake pad.

NOTICE:

Install the pad wear indicator plate in the correct position and direction.



Hide 04945 10.INSTALL FRONT ANTI-SQUEAL SHIM KIT

a.
C323743C01
0.542,1.469 0.542,1.948 false 3.01,2.625 3.01,3.031 3.01,3.031 2.719,3.031 false 1.198,1.094 1.198,0.802 1.198,0.802 2.375,0.802 false 2.052,1.5 2.052,0.813 false 2.438,0.74 2.677,0.917 0.24,0.177 10 false *1 0.458,2.01 0.656,2.167 0.198,0.156 10 false *2 2.51,2.979 2.688,3.135 0.177,0.156 10 false *2
*1 Front Disc Brake Pad
*2 No. 1 Anti-squeal Shim


Install the 2 No. 1 anti-squeal shims to the front disc brake pads.

NOTICE:

When replacing a worn pad, the shims must be replaced together with the pads.



Hide 04465 11.INSTALL FRONT DISC BRAKE PAD

a.

Install the 2 front disc brake pads with the 2 No. 1 anti-squeal shims to the disc brake cylinder mounting LH.

NOTICE:

Make sure there is no oil or grease on the friction surfaces of the front disc brake pads and front disc.



b.
C321903

Install the 2 anti-squeal springs to the front disc brake pads.

NOTICE:
·

When replacing the front disc brake pads with new ones, make sure to replace the anti-squeal springs at the same time.

·

Be sure to install the anti-squeal springs into the front disc brake pad installation holes as far as they will go.




Hide 47750 12.INSTALL DISC BRAKE CYLINDER ASSEMBLY LH

a.
C321896C01
1.948,2.063 2.031,1.885 2.031,1.885 2.146,1.885 true 1.333,2.208 0.948,2.438 0.948,2.438 0.74,2.438 true 0.51,2.354 0.729,2.521 0.219,0.167 10 false *a 2.188,1.802 2.375,1.969 0.188,0.167 10 true *b
*a Hold
*b Turn


Hold the front disc brake cylinder slide pin and install the disc brake cylinder assembly LH to the disc brake cylinder mounting LH with the 2 bolts.

Torque:
34.3 N*m (350 kgf*cm, 25 ft.*lbf)

NOTICE:
·

Install the disc brake cylinder assembly LH while holding both of the front disc brake pads because the anti-squeal springs may fall off the front disc brake pads.

·

Be sure that the anti-squeal springs are installed to the front disc brake pads.




Hide 47313A 13.CONNECT FRONT FLEXIBLE HOSE

a.

Connect the front flexible hose to the disc brake cylinder assembly LH with a new gasket and a new union bolt.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)

HINT:

Install the front flexible lock securely in the lock hole in the disc brake cylinder assembly LH.



Hide 14.BLEED BRAKE LINE (w/ VSC)

Hide 15.BLEED BRAKE LINE (w/o VSC)

Hide 16.BLEED CLUTCH LINE (for Manual Transmission)

Hide 17.INSTALL FRONT WHEEL