Home › Brake › BRAKE (FRONT) › FRONT DISC BRAKE PAD(for 4WD and Pre-Runner)
RM33J0E _54 Brake _038479 BRAKE (FRONT) _0193993 FRONT DISC BRAKE PAD(for 4WD and Pre-Runner) A

BRAKE (FRONT)  FRONT DISC BRAKE PAD(for 4WD and Pre-Runner)  REPLACEMENT  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



NOTICE:

After replacing the disc brake pads, the clearance between the disc brake pads and front discs becomes larger and the brake pedal feel becomes softer. Therefore, after replacing the disc brake pads, depress the brake pedal several times and check the clearance and brake pedal feel.


PROCEDURE

Hide 1.REMOVE FRONT WHEEL

Hide 2.DRAIN BRAKE FLUID

NOTICE:

Wash off brake fluid immediately if it comes in contact with any painted surface.


Hide 04947 3.REMOVE FRONT DISC BRAKE ANTI-RATTLE SPRING

a.

for 15 inch Front Disc Brake (Type A):

i.
C321907C01
1.042,0.438 0.75,0.438 true 1.771,1.615 1.458,1.188 1.458,1.188 1,1.188 true 1.25,1.948 0.635,1.948 true 2.323,1.24 2.667,1.396 2.667,1.396 2.896,1.396 true 0.542,0.375 0.75,0.542 0.208,0.167 10 true *1 2.938,1.323 3.177,1.49 0.24,0.167 10 true *2 0.771,1.125 0.99,1.281 0.219,0.156 10 true *3 0.406,1.885 0.615,2.052 0.208,0.167 10 true *1
*1 Disc Brake Pad Guide Pin
*2 Pin Hold Clip
*3 Front Disc Brake Anti-rattle Spring


Remove the pin hold clip and 2 disc brake pad guide pins.


ii.

Remove the front disc brake anti-rattle spring.

NOTICE:

The front disc brake anti-rattle spring can be reused if it has sufficient rebound; no deformation, cracks or wear; and has all rust, dirt and foreign matter cleaned off.




b.

for 15 inch Front Disc Brake (Type B):

i.
C334251C01
2.333,1.219 2.583,1.333 2.583,1.333 2.76,1.333 true 1.135,0.469 0.833,0.469 true 1.323,1.115 0.865,1.115 true 1.344,1.969 0.979,1.969 true 0.604,0.406 0.813,0.573 0.208,0.167 10 true *1 2.865,1.229 3.083,1.385 0.219,0.156 10 true *2 0.625,1.042 0.854,1.208 0.229,0.167 10 true *3 0.74,1.906 0.948,2.073 0.208,0.167 10 true *1
*1 Disc Brake Pad Guide Pin
*2 Pin Hold Clip
*3 Front Disc Brake Anti-rattle Spring


Remove the pin hold clip.


ii.

Hold down the anti-rattle spring and remove the 2 disc brake pad guide pins.


iii.

Remove the anti-rattle spring.

CAUTION:

Do not remove the 2 disc brake pad guide pins without holding down the anti-rattle spring. The anti-rattle spring will eject with a force capable of causing injury.




c.

for 16 inch Front Disc Brake (Type A):

i.
C321908C01
1.063,0.479 0.698,0.479 true 1.271,2.021 0.896,1.781 0.896,1.781 0.656,1.781 true 1.698,1.635 1.385,1.292 1.385,1.292 1.188,1.292 true 2.302,0.25 2.5,0.49 2.5,0.49 2.74,0.49 true 2.438,1.646 2.771,1.646 true 0.49,0.417 0.677,0.594 0.188,0.177 10 true *1 2.76,0.406 2.969,0.583 0.208,0.177 10 true *2 0.979,1.229 1.167,1.396 0.188,0.167 10 true *3 0.469,1.708 0.656,1.885 0.188,0.177 10 true *1 2.813,1.573 3.021,1.75 0.208,0.177 10 true *2
*1 Disc Brake Pad Guide Pin
*2 Pin Hold Clip
*3 Front Disc Brake Anti-rattle Spring


Remove the 2 pin hold clips and 2 disc brake pad guide pins.


ii.

Remove the front disc brake anti-rattle spring.

NOTICE:

The front disc brake anti-rattle spring can be reused if it has sufficient rebound; no deformation, cracks or wear; and has all rust, dirt and foreign matter cleaned off.




d.

for 16 inch Front Disc Brake (Type B):

i.
C334252C01
1.104,0.427 0.76,0.427 true 1.323,2.021 0.885,2.021 true 1.302,1.125 0.885,1.125 true 2.438,1.688 2.781,1.688 false 2.292,0.229 2.49,0.406 2.49,0.406 2.688,0.406 true 0.51,0.365 0.76,0.521 0.25,0.156 10 true *1 2.719,0.344 2.917,0.531 0.198,0.188 10 true *2 0.677,1.031 0.875,1.188 0.198,0.156 10 true *3 0.688,1.948 0.875,2.104 0.188,0.156 10 true *1 2.833,1.615 3.104,1.781 0.271,0.167 10 true *2
*1 Disc Brake Pad Guide Pin
*2 Pin Hold Clip
*3 Front Disc Brake Anti-rattle Spring


Remove the 2 pin hold clips.


ii.

Hold down the anti-rattle spring and remove the 2 disc brake pad guide pins.


iii.

Remove the anti-rattle spring.

CAUTION:

Do not remove the 2 disc brake pad guide pins without holding down the anti-rattle spring. The anti-rattle spring will eject with a force capable of causing injury.




Hide 04465 4.REMOVE FRONT DISC BRAKE PAD

a.

Remove the 2 front disc brake pads from the disc brake cylinder assembly LH.


Hide 04945 5.REMOVE FRONT ANTI-SQUEAL SHIM KIT

a.

Remove the 2 No. 1 anti-squeal shims and 2 No. 2 anti-squeal shims from each pad.


Hide 04945 6.INSTALL FRONT ANTI-SQUEAL SHIM KIT

a.
C321920C01
0.219,0.552 0.219,0.25 0.219,0.25 0.594,0.25 false 0.906,1.729 0.906,2.333 false 2.594,2.698 2.594,3.052 false 3.063,2.208 3.063,1.302 3.063,1.302 2.813,1.302 false 1.365,1.198 1.365,0.594 1.365,0.594 2.094,0.594 false 1.854,1.521 1.854,0.594 false 0.844,2.396 1.156,2.552 0.313,0.156 10 false *2 2.531,3.083 2.729,3.24 0.198,0.156 10 false *2 2.167,0.531 2.354,0.688 0.188,0.156 10 false *1 0.635,0.188 0.833,0.344 0.198,0.156 10 false *3 2.583,1.25 2.781,1.406 0.198,0.156 10 false *3
*1 Front Disc Brake Pad
*2 No. 1 Anti-squeal Shim
*3 No. 2 Anti-squeal Shim
V100135

Disc Brake Grease


except 16 inch Front Disc Brake (Type B):

i.

Apply disc brake grease to both sides of each No. 1 anti-squeal shim.

NOTICE:

For 16 inch Front Disc Brake (type B), do not apply disc brake grease.




b.

Install the No. 1 anti-squeal shims and No. 2 anti-squeal shims to each pad.

NOTICE:
·

When replacing worn front disc brake pads, the anti-squeal shims must be replaced together with the front disc brake pads.

·

Install the anti-squeal shims in the correct positions and directions as shown in the illustration.




Hide 04465 7.INSTALL FRONT DISC BRAKE PAD

a.
C323347C01
2,1.719 2,1.917 2,1.917 1.792,1.917 false 1.469,1.844 1.802,2.031 0.333,0.188 10 false SST
V113147

Expand


Using SST, push back the front disc brake piston.

NOTICE:

Do not forcibly install the piston into the disc brake cylinder assembly LH.


SST
09719-77020  


b.

Install the 2 front disc brake pads to the disc brake cylinder assembly LH.

NOTICE:

Make sure there is no oil or grease on the friction surface of the front disc brake pads and front disc.



Hide 04947 8.INSTALL FRONT DISC BRAKE ANTI-RATTLE SPRING

a.

for 15 inch Front Disc Brake(Type A):

i.

Install the 2 disc brake pad guide pins and front disc brake anti-rattle spring.

HINT:

Install the front disc brake anti-rattle spring together with the disc brake pad guide pin on the bottom side.



ii.

Install the pin hold clip.



b.

for 15 inch Front Disc Brake (Type B):

i.

Install the front disc brake anti-rattle spring.


ii.

Hold down the front disc brake anti-rattle spring and insert the 2 disc brake pad guide pins.


iii.

Install the pin hold clip.



c.

for 16 inch Front Disc Brake (Type A):

i.

Install the 2 disc brake pad guide pins and front disc brake anti-rattle spring.

HINT:

Install the front disc brake anti-rattle spring together with the disc brake pad guide pin on the bottom side.



ii.

Install the 2 pin hold clips.

NOTICE:

When installing the pin hold clip, be sure to install the pin hold clip with the handle facing the center of the vehicle.




d.

for 16 inch Front Disc Brake (Type B):

i.

Install the front disc brake anti-rattle spring.


ii.

Hold down the front disc brake anti-rattle spring and insert the 2 disc brake pad guide pins.


iii.

Install the 2 clips.

NOTICE:

When installing the pin hold clip, be sure to install the pin hold clip with the handle facing the center of the vehicle.




e.

Depress the brake pedal several times.


Hide 10.INSTALL FRONT WHEEL